International Research Journal of Engineering and Technology (IRJET)
e-ISSN: 2395 -0056
Volume: 04 Issue: 03 | Mar -2017
p-ISSN: 2395-0072
www.irjet.net
Excavator Monitoring And Auto Reporting Using GSM Swati M. Nagargoje1, Priyanka D. Kantak2, Priyanka N. Tupe3 Professor Mr. Akshay Bhosale 4
Department of Electronics and Telecommunication Engineering Sanjay Ghodawat Institute, Atigre, Maharashtra, India ---------------------------------------------------------------------***---------------------------------------------------------------------
Abstract - Excavator monitoring system combines the
installation of electronics devices in a poclains, tractors, bulldozer excavator with the purpose design to enable the owner to know status of working machine. In the excavator monitoring system Arduino is used as central processing unit for storing the data and then all data send to the owner. Global position system(GPS) technology used for locating the machine. It will track the location of the machine and then this information can be viewed on electronic maps via the internet or specialized software. In this system sensors are used for detecting the exact fuel filling and working hours and Global system for mobile(GSM) is used for sending the information of machine to the owner cell phone. The owner may not get the real information from the operator about the work location, exact fuel filling, work hours etc. several time with wrong input of the work hours given by the operators, because of this the owners are not getting the accurate output in teams of money . So considering these problem the system is to be design for the owner of the machine. Key Words: Global Positioning System module(GPS), Global system for moile module (GSM), Arduino board , Fuel level sensor and Accelerometer Sensor.
1.INTRODUCTION Now a days for the owners having several number of excavator machines. In case of constructions, mining, transportation and agricultural work the earth movers like bulldozer, excavator, tractors and poclains plays very important roles. For each machine there is one operator allocated. The major problem faced by the owners is there is no any direct control on the operators of the poclains machines. The owner may not get the real information from the operators about the work location, the exact fuel filling, work hours etc. several times with the wrong input of the work hours is told by the operator, because of the owners are not getting the adequate output in terms of money. Also several time the operator may not take care of the condition of the machine. Also the owner can not keep watch on their excavator machine, when it moves in different places, therefore malfunctioning with them takes place. If this machine controller by remotely, then owner can catch the Š 2017, IRJET
|
Impact Factor value: 5.181
|
every movements of the machines. Like work location, working hours, ignition status etc. So considering this problem the system is to be designed for the owner of the machine. This system will monitor the machine and display information like start time, fuel level, work location etc. On the mobile of the owner by sending message using GSM.[1]
2. DESIGN OF HARDWARE SYSTEM 2.1) System structure In proposed work the system consist of arduino, GSM module, GPS module, LCD and the sensors. The sensor interfaces can be connected to the earthmovers unities for the detection of a variety of status data. The block diagram of terminal board is shown in figure. The hardware structure of the system is dominated by arduino, GPS module and GSM module and other components. This design adapts the current leading GPS technology and the integrated positioning. A GPS receiver module with the high sensitivity, low power consumption and 20 channels solution to help users gain and continuously track GPS signal at a very low signal intensity, which means can be used in the environment where it has never been thought to accessible, such as buildings in the city, dense forest and many indoor environment, with positioning accuracy less than 10 meters. GSM module is used for wireless communication having gained domestic network card of radio equipment, it operates in dual band GSM 900 with a power consumption of 2W and 1W respectively. Through this interface, system can have real time monitoring of earthmovers information, in order to make response timely. The GPS tracks latitude and longitude of earthmover. With the help of multimedia cell phone or PC with internet, we can find exact location of the earthmover equipper with the system. In case of power failure transaction details are retained or stored on to the arduino and available for use when the power supply is resume, and this includes transaction in process at the time of the power failure which are automatically saved. This system is not only useful for control and stop the fuel theft
ISO 9001:2008 Certified Journal
|
Page 313