Industrial Technology
Final Exam
Course Introduction
Industrial Technology is an interdisciplinary course that explores the application of engineering principles and technological advancements in manufacturing and production environments. Students learn about materials science, industrial processes, quality control, automation, and systems management. The course emphasizes problem-solving, innovation, and the integration of emerging technologies, such as robotics and digital manufacturing, to improve efficiency and productivity. Through a combination of theoretical learning and practical projects, students gain the skills necessary to address challenges in modern industrial operations and prepare for careers in various technological fields.
Recommended Textbook
Print Reading for Engineering and Manufacturing Technology 3rd Edition by David A Madsen
Available Study Resources on Quizplus
17 Chapters
1502 Verified Questions
1502 Flashcards
Source URL: https://quizplus.com/study-set/259
Page 2
Chapter 1: Introduction to Engineering and Manufacturing
Technology Print Reading
Available Study Resources on Quizplus for this Chatper
63 Verified Questions
63 Flashcards
Source URL: https://quizplus.com/quiz/4257
Sample Questions
Q1) A scale that reads 1:2 is a(n):
A) architect's scale
B) metric scale
C) civil engineer's scale
D) full scale
E) half scale
Answer: E
Q2) A scale is an instrument with a system of ordered marks at fixed intervals used as a reference standard in measurement.
A)True
B)False
Answer: True
Q3) The _________________________ is a five number code assigned by the Defense Logistic Service Center to all Department of Defense Contractors.
Answer: CAGE Code
Q4) The civil engineer's scales are calibrated in multiples of ten.
A)True
B)False
Answer: True
Page 3
To view all questions and flashcards with answers, click on the resource link above.
Chapter 2: Communicating with a Sketch
Available Study Resources on Quizplus for this Chatper
84 Verified Questions
84 Flashcards
Source URL: https://quizplus.com/quiz/4258
Sample Questions
Q1) What are some of the things you can ask yourself when sketching that will help keep the sketch in proportion?
A) Is this next line longer than the previous line I drew?
B) Is this next line perpendicular to my previous line?
C) Should this line be darker than the previous line?
D) all of the above
E) both a and b
Answer: E
Q2) Sketching and aligning the proportional rectangles for a multiview sketch is an important first step.
A)True
B)False
Answer: True
Q3) Lines that are not parallel to one of the three isometric axes lines are called ____________________.
Answer: non-isometric
Q4) Why is it best to keep the sketching paper free to move?
Answer: The best sketches are made when you are able to move the paper to the most comfortable drawing position.
To view all questions and flashcards with answers, click on the resource link above. Page 4
Chapter 3: Scales and Precision Measurement
Available Study Resources on Quizplus for this Chatper
32 Verified Questions
32 Flashcards
Source URL: https://quizplus.com/quiz/4259
Sample Questions
Q1) Briefly describe a dial caliper and indicate how the caliper range is determined.
Answer: The dial caliper, like the vernier caliper, has a movable slide assembly and a stationary bar. The caliper range is determined by the length of slide travel, such as 0 to 6 inches.
Q2) The scale of a drawing is usually noted in the title block or below the view or elevation of the object being drawn. What are the factors that control the selection of a scale?
Answer: The actual size of the part
The amount of detail to be shown
The paper size selected
The amount of dimensioning and notes required on the part
Q3) The ____________________ is the most commonly used linear unit of measure for engineering drawings in the United States. Answer: inch (IN)
IN (inch)
Inch IN
To view all questions and flashcards with answers, click on the resource link above.
5
Chapter 4: Reading Lines and Lettering on a Print
Available Study Resources on Quizplus for this Chatper
45 Verified Questions
45 Flashcards
Source URL: https://quizplus.com/quiz/4260
Sample Questions
Q1) A "bolt circle" is a pattern of holes arranged in a circle.
A)True
B)False
Q2) The arrowhead is omitted when a leader line points to a dimension line. This is done when there is not enough space for text to be inserted at the dimension line, and the text is connected to the leader.
A)True
B)False
Q3) A hidden line is ____.
A) dashed
B) thick
C) dotted
D) straight
E) none of the above
Q4) The American Society of Mechanical Engineers (ASME) recommends two-line thickness, which are thick and thin lines.
A)True
B)False
Q5) Define font.
Q6) What are centerlines used to show and locate?
Page 6
To view all questions and flashcards with answers, click on the resource link above.
Chapter 5: Reading Multiviews
Available Study Resources on Quizplus for this Chatper
94 Verified Questions
94 Flashcards
Source URL: https://quizplus.com/quiz/4261
Sample Questions
Q1) When the glass box is unfolded, how many views are created and what are the names for these views?
Q2) Fillets are slightly rounded outside curves at corners.
A)True
B)False
Q3) Rotating views from their normal alignment with the six principal views should be avoided, but it is possible if necessary. Describe when rotating views is necessary, and explain how the rotating view method is established.
Q4) The _________________________ is perpendicular to the plane of projection.
Q5) The depth of an object shown in a multiview print is common between ____.
A) the front view and the top view
B) the front view and the right side view
C) the top view and the right side view
D) the rear view and the left side view
E) the rear view and the bottom view
Q6) A pictorial view shows three sides of an object.
A)True
B)False
Q7) What is a chamfer and why is it used?
Page 7
To view all questions and flashcards with answers, click on the resource link above.
Chapter 6: Reading Auxiliary Views
Available Study Resources on Quizplus for this Chatper
32 Verified Questions
32 Flashcards
Source URL: https://quizplus.com/quiz/4262
Sample Questions
Q1) What is it called when a surface feature is not perpendicular to the line of sight?
Q2) The full auxiliary view shows the true size and shape of the inclined surface.
A)True
B)False
Q3) This auxiliary view shows only the true size and shape of the inclined surface.
A) full
B) surface
C) partial
D) incomplete
E) none of the above
Q4) When a surface feature is perpendicular to the line of sight, the feature is said to be foreshortened, or shorter than true length.
A)True
B)False
Q5) Define secondary auxiliary view.
Q6) An auxiliary view allows you to look directly at the inclined surface.
A)True
B)False
Q7) Describe the use of a removed auxiliary view application.
Page 8
To view all questions and flashcards with answers, click on the resource link above.
Chapter 7: Manufacturing Materials and Processes
Available Study Resources on Quizplus for this Chatper
188 Verified Questions
188 Flashcards
Source URL: https://quizplus.com/quiz/4263
Sample Questions
Q1) ____ is a process of shaping malleable metals by hammering or pressing between dies that duplicate the desired shape.
A) Adhesion
B) Fusion
C) Ductility
D) Forging
E) none of the above
Q2) Name the material that uses additional forming of steel after initial hot rolling, and where the process is used to clean up hot-formed steel, provide a smooth, clean surface, ensure dimensional accuracy, and increase the tensile strength of the finished product.
Q3) The process of blow molding works by blowing hot polymer against the internal surfaces of a hollow mold.
A)True
B)False
Q4) Define forging
Q5) Define core.
Q6) Name a method of monitoring a process quantitatively and using statistical signals to either leave the process alone, or change the process.
Page 9
To view all questions and flashcards with answers, click on the resource link above.
Chapter 8: Reading Dimensions
Available Study Resources on Quizplus for this Chatper
125 Verified Questions
125 Flashcards
Source URL: https://quizplus.com/quiz/4264
Sample Questions
Q1) ____ usually show draft.
A) Machining prints
B) Casting prints
C) Investment casting prints
D) Forging detail prints
E) none of the above
Q2) The standard for the control of metric limits and fits is governed by the document ANSI B4.2 ____.
A) Dimensioning and Tolerancing
B) Metric Print Sheet Size and Format
C) Preferred Metric Limits and Fits
D) Dimensioning and Tolerance Fits
E) none of the above
Q3) Describe how a leader line is displayed on a print.
Q4) This term means the limits of the radius tolerance zone must be tangent to the adjacent surfaces, and there can be no reversals in the contour.
Q5) Describe unidirectional dimensioning.
Q6) Give another name for flag note and completely describe how a flag note is used.
Q7) Describe and give another name for chain dimensioning.
Page 10
To view all questions and flashcards with answers, click on the resource link above.
Chapter 9: Reading Prints With Fasteners and Springs
Available Study Resources on Quizplus for this Chatper
141 Verified Questions
141 Flashcards
Source URL: https://quizplus.com/quiz/4265
Sample Questions
Q1) Which of the following is not a set screw point style?
A) dog point
B) quarter dog point
C) oval point
D) cone point
E) none of the above
Q2) A self-clinching fastener is any device, usually threaded, that displaces the material around a mounting hole when pressed into a properly sized drilled or punched hole.
A)True
B)False
Q3) Rivets are classified by ____.
A) length
B) head type
C) body diameter
D) all of the above
E) none of the above
Q4) Specify the three methods of thread representations, and which is most commonly used on prints?
Q5) Define pitch as used in spring terminology.
To view all questions and flashcards with answers, click on the resource link above. Page 11
Chapter 10: Reading Sections, Revolutions, and
Conventional Breaks
Available Study Resources on Quizplus for this Chatper
112 Verified Questions
112 Flashcards
Source URL: https://quizplus.com/quiz/4266
Sample Questions
Q1) Very thin features, less than .06 in. (4 mm) thick, can be shown on the print ____________ section lines.
Q2) Multiple removed sections ____.
A) must all have a line of sight that points the same direction
B) must be the same scale as the part from which they were taken
C) do not generally show hidden lines
D) do not generally need to be labeled
E) none of the above
Q3) Which of the following objects are usually sectioned?
A) gaskets
B) bolts
C) gear teeth
D) webs
E) none of the above
Q4) A half section is used typically for symmetrical objects; the cutting-plane line actually cuts through one quarter of the part. The sectional view shows half of the interior and half of the exterior at the same time.
A)True
B)False
12
To view all questions and flashcards with answers, click on the resource link above.
Chapter 11: Reading Geometric Dimensioning and Tolerancing
Available Study Resources on Quizplus for this Chatper
129 Verified Questions
129 Flashcards
Source URL: https://quizplus.com/quiz/4267
Sample Questions
Q1) The primary, secondary, and tertiary datum planes are equally important.
A)True
B)False
Q2) A ____ geometric tolerance requires that a given feature be located between two parallel planes or lines at ninety degrees to a datum.
A) parallelism
B) perpendicularity
C) angularity
D) circularity
E) none of the above
Q3) A cylinder is given the dimension Ø 18.2/17.8. The feature control frame has one horizontal line as the first element, and Ø 0.1 as the second element. What does this mean?
A) The straightness tolerance is applied to the axis of the cylinder.
B) The MMC is 18.3.
C) The LMC is 17.8.
D) both a and c
E) all of the above
Q4) List the five types of geometric tolerances.
Q5) How is a datum target line indicated on a drawing?
To view all questions and flashcards with answers, click on the resource link above. Page 13
Chapter
Available Study Resources on Quizplus for this Chatper
80 Verified Questions
80 Flashcards
Source URL: https://quizplus.com/quiz/4268
Sample Questions
Q1) The elements of the gear structure include the face, hub, bore, keyway, and outside diameter.
A)True
B)False
Q2) A "lead" is one of the terms used for ____.
A) rack and pinion gears
B) worm gears
C) sleeve bearings
D) hypoid gears
E) none of the above
Q3) Circular pitch is the distance from a point on one tooth to the corresponding point on the adjacent tooth, measured on the pitch circle.
A)True
B)False
Q4) What is a cam?
Q5) The base circle, which surrounds the cam shaft, is a member of a cam mechanism.
A)True
B)False
Q6) Define dwell related to cam terminology.
Q7) Describe the A, B, and C gear hubs.
To view all questions and flashcards with answers, click on the resource link above. Page 14
Chapter 13: Reading Precision Sheet Metal Prints
Available Study Resources on Quizplus for this Chatper
66 Verified Questions
66 Flashcards
Source URL: https://quizplus.com/quiz/4269
Sample Questions
Q1) Bend radius is typically added to a sheet metal part to relieve stress, or the tear that occurs when a portion of a piece of material is bent.
A)True
B)False
Q2) Describe the practice for representing a sheet metal part using a flat pattern with manufacturing information extracted to a table.
Q3) IML is identify middle line of bend.
A)True
B)False
Q4) This is a stamping press operation that forms a single-line cut partway across the sheet without removing material.
Q5) A flange is a feature added to a sheet metal part to reinforce or stiffen a part edge or to provide a surface for fastening or welding.
A)True
B)False
Q6) This is a sheet metal feature that creates a curved sheet metal feature in a linear application on flat material or around an axis.
To view all questions and flashcards with answers, click on the resource link above.
Page 15
Chapter 14: Reading Prints of Working Drawings
Available Study Resources on Quizplus for this Chatper
87 Verified Questions
87 Flashcards
Source URL: https://quizplus.com/quiz/4270
Sample Questions
Q1) Associated with the assembly print and coordinated to the detail prints is ____.
A) the parts list
B) the monodetail print
C) outside supplier of parts
D) the multidetail print
E) none of the above
Q2) What is a detail drawing?
Q3) ____ are parts that are manufactured and available for purchase from an outside vendor.
A) Purchase parts
B) Prototype parts
C) Standard parts
D) both a and c
E) none of the above
Q4) When making a change to a part, it is preferable to leave the part drawn as is and change the dimension instead, noting that the part is "not to scale."
A)True
B)False
Q5) Which branch of a company can request engineering changes to prints?
Q6) What is an assembly print?
To view all questions and flashcards with answers, click on the resource link above. Page 16
Chapter 15: Welding Processes and Reading Welding
Representations
Available Study Resources on Quizplus for this Chatper
93 Verified Questions
93 Flashcards
Source URL: https://quizplus.com/quiz/4271
Sample Questions
Q1) Oxygen gas welding can only be performed with natural gas fuel.
A)True
B)False
Q2) The weld symbol in which a small circle is drawn with its center at the intersection of the leader line and the reference line means ____.
A) it is a field weld
B) it is a plug and slot weld
C) to weld all around
D) to spot weld
E) none of the above
Q3) Welding is a more permanent fastening application than screw threads or pins.
A)True
B)False
Q4) The continuity of a weld is when the desired characteristics of the weld exist throughout the weld length.
A)True
B)False
Q5) Gas tungsten welding is sometimes called?
Q6) What are some of the advantages of welding?
To view all questions and flashcards with answers, click on the resource link above. Page 17
Chapter 16: Reading Prints of Pictorial Drawings
Available Study Resources on Quizplus for this Chatper
61 Verified Questions
61 Flashcards
Source URL: https://quizplus.com/quiz/4272
Sample Questions
Q1) The most basic form of shading is called straightline shading.
A)True
B)False
Q2) Centerlines in an exploded assembly drawing are parallel to the axis lines of the drawing.
A)True
B)False
Q3) One-point perspective is also known as parallel perspective.
A)True
B)False
Q4) Thin solid extension lines are used to connect between non-cylindrical features, parts, and subassemblies. These lines are called connection lines or trails.
A)True
B)False
Q5) Depending on the purpose of the exploded isometric assembly, the parts can be shown without identification, or they can be identified with balloons.
A)True
B)False
Q6) Completely describe an explode assembly and its use.
Page 18
To view all questions and flashcards with answers, click on the resource link above.
Chapter 17: Reading Electrical Diagrams and Schematics
Available Study Resources on Quizplus for this Chatper
70 Verified Questions
70 Flashcards
Source URL: https://quizplus.com/quiz/4273
Sample Questions
Q1) All electronic component values are extremely large (2,500,000,000,000).
A)True
B)False
Q2) Symbols exhibit a minimum of detail of the component and generally no connections at individual terminals
A)pictorial
B)schematic
C)block
D)wiring
E)schematic wiring
F)highway wiring
G)wireless
H)cable
Q3) Printed circuit boards do not need to have separate mounting holes for each component lead or terminal.
A)True
B)False
Q4) ____________________ are drawn as a series of lines and symbols representing the electrical current path and the components of the circuit.
To view all questions and flashcards with answers, click on the resource link above. Page 19