Course Introduction
Industrial
Technology
Exam Questions
Industrial Technology explores the practical applications of science, engineering, and management principles in the manufacturing and service industries. This course examines topics such as production processes, quality control, materials science, industrial safety, project management, and systems optimization. Students will learn how to utilize modern tools and techniques to improve efficiency, ensure sustainability, and maintain competitiveness in todays fast-evolving industrial landscape. Through both theoretical study and hands-on projects, the course prepares students for careers in industrial operations, technical management, and technology innovation.
Recommended Textbook
Print Reading for Engineering and Manufacturing Technology 3rd Edition by David A Madsen
Available Study Resources on Quizplus
17 Chapters
1502 Verified Questions
1502 Flashcards
Source URL: https://quizplus.com/study-set/259
Page 2
Chapter 1: Introduction to Engineering and Manufacturing
Technology Print Reading
Available Study Resources on Quizplus for this Chatper
63 Verified Questions
63 Flashcards
Source URL: https://quizplus.com/quiz/4257
Sample Questions
Q1) Describe and give the function of the dimensioning and tolerancing block.
Answer: The dimensioning and tolerancing block is used to specify the general dimensioning and tolerancing specifications found on the drawing. Typically, the upper portion of the dimensioning and tolerancing block provides a note indicating that all dimensions are in millimeters (mm) or inches (IN), unless otherwise specified, such as UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES (IN). The compartment continues with information about unspecified tolerances.
Q2) Millimeter
A)cm
B)hm
C)darn
D)km
E)dm
F)mm
G)m
Answer: F
Q3) Define border.
Answer: The border is the format margin of a sheet, usually between the edges of the sheet to borderlines.
To view all questions and flashcards with answers, click on the resource link above. Page 3
Chapter 2: Communicating with a Sketch
Available Study Resources on Quizplus for this Chatper
84 Verified Questions
84 Flashcards
Source URL: https://quizplus.com/quiz/4258
Sample Questions
Q1) A good sketch can assist the drafter by allowing which of the following?
A) the determination of how big to make the drawing
B) the determination of how the drawing should appear when finished
C) the determination of sheet size or screen limit for the drawing
D) all of the above
E) none of the above
Answer: D
Q2) Sketching equipment is not elaborate. All you need are these three items
Answer: paper, pencil and an eraser paper, an eraser and a pencil pencil, paper and an eraser pencil, an eraser and paper
An eraser, pencil and paper
An eraser, paper and a pencil
Q3) Sketching and aligning the proportional rectangles for a multiview sketch is an important first step.
A)True
B)False
Answer: True
To view all questions and flashcards with answers, click on the resource link above. Page 4
Chapter 3: Scales and Precision Measurement
Available Study Resources on Quizplus for this Chatper
32 Verified Questions
32 Flashcards
Source URL: https://quizplus.com/quiz/4259
Sample Questions
Q1) Decimeter
A)cm
B)hm
C)dam
D)km
E)dm
F)mm
G)m
Answer: E
Q2) A scale establishes a proportion used in determining the dimensional relationship of an actual object to the representation of the same object on a drawing.
A)True
B)False
Answer: True
Q3) A mechanical engineer's scale is commonly used when drawings are in:
A) fractional or decimal inches
B) decimal inches
C) miles
D) all of the above
Answer: A
To view all questions and flashcards with answers, click on the resource link above. Page 5
Chapter 4: Reading Lines and Lettering on a Print
Available Study Resources on Quizplus for this Chatper
45 Verified Questions
45 Flashcards
Source URL: https://quizplus.com/quiz/4260
Sample Questions
Q1) A section line is similar to a visible object line, except it is ____.
A) dashed
B) thicker
C) dotted
D) straighter
E) none of the above
Q2) Thick lines used to show where a section view is taken.
A)chain line
B)object line
C)stitch line
D)hidden line
E)phantom line
F)section line
G)break line
H)leader line
I)cutting-plane line
J)construction line
K)dimension line
L)extension line
Q3) Define font.
To view all questions and flashcards with answers, click on the resource link above. Page 6
Chapter 5: Reading Multiviews
Available Study Resources on Quizplus for this Chatper
94 Verified Questions
94 Flashcards
Source URL: https://quizplus.com/quiz/4261
Sample Questions
Q1) A view enlargement ____.
A) is used primarily when a detail that needs to be dimensioned is too small to show the dimensions clearly
B) is a view with a larger scale than that used on the regular multiviews
C) has a thick phantom line circle around the area to be enlarged with a detail view identification letter
D) both a and c
E) all of the above
Q2) Partial views can be used when symmetrical objects are drawn in limited space or when there is a desire to simplify complex views.
A)True
B)False
Q3) Cylindrical shapes appear round in one view and ____________________ in another view.
Q4) An enlarged view is shown directly above the portion of view from which it came. A)True
B)False
Q5) Which view of a multiview drawing is usually most important and why?
Q6) The _________________________ is perpendicular to the plane of projection.
Page 7
To view all questions and flashcards with answers, click on the resource link above.
Chapter 6: Reading Auxiliary Views
Available Study Resources on Quizplus for this Chatper
32 Verified Questions
32 Flashcards
Source URL: https://quizplus.com/quiz/4262
Sample Questions
Q1) When it is not possible to align the auxiliary view directly from the inclined surface, then a viewing-plane line can be used and the view placed in a convenient location on the sheet.
A)True
B)False
Q2) Describe the use of a removed auxiliary view application.
Q3) When a surface feature is not perpendicular to the line of sight, the feature is said to be:
A) parallel
B) foreshortened
C) at right angles
D) True length
E) none of the above
Q4) Describe the method called cross-reference zoning used to indicate the location of a view back to the viewing location on a previous page.
Q5) Primary auxiliary views are views that take the place of a principal view.
A)True
B)False
Q6) Describe the use of an auxiliary view enlargement application.
Page 8
To view all questions and flashcards with answers, click on the resource link above.
Chapter 7: Manufacturing Materials and Processes
Available Study Resources on Quizplus for this Chatper
188 Verified Questions
188 Flashcards
Source URL: https://quizplus.com/quiz/4263
Sample Questions
Q1) An alloy of iron containing 0.8% to 1.5% carbon
A)Gray Cast Iron
B)White Cast Iron
C)Chilled Cast Iron
D)Steel
E)Stainless Steel
F)Aluminum
G)Copper Alloy
H)Brass
I)Bronze
J)Titanium
Q2) Define and give a use for countersink.
Q3) Identify the process of heating the steel to a specified temperature and then allowing the material to cool slowly by air.
Q4) Select a process used to make manufactured composites.
A) layering process
B) lamination
C) vacuum bag forming
D) both a and c
Q5) Explain the difference between a drill and a ream.
Page 9
To view all questions and flashcards with answers, click on the resource link above.
Chapter 8: Reading Dimensions
Available Study Resources on Quizplus for this Chatper
125 Verified Questions
125 Flashcards
Source URL: https://quizplus.com/quiz/4264
Sample Questions
Q1) What are specifications?
Q2) The application of fillets and rounds to forging dies is to ____. A) rejection of the metal from the die B) improve the retention of the metal by the die C) improve the ejection of the metal from the die D) both a and b E) none of the above
Q3) Describe tabular dimensioning.
Q4) Describe how arcs are dimensioned.
Q5) A slash is used at the end of a dimension line on a manufactured part print.
A)True
B)False
Q6) Angular surfaces are never dimensioned as coordinates, as angles and degrees, or as a flat taper.
A)True
B)False
Q7) A complete detail print includes multiviews and dimensions that provide neither shape nor size description.
A)True
B)False
To view all questions and flashcards with answers, click on the resource link above. Page 10
Chapter 9: Reading Prints With Fasteners and Springs
Available Study Resources on Quizplus for this Chatper
141 Verified Questions
141 Flashcards
Source URL: https://quizplus.com/quiz/4265
Sample Questions
Q1) The top of external and the bottom of internal threads is the ____.
A) pitch
B) root
C) crest
D) fit
E) none of the above
Q2) Name the type of springs that are designed to provide resistance or to exert a turning force in a plane at 90° to the axis of the coil.
Q3) List and describe the components of this thread note by specifying A through D: 1/2-13 UNC-2A [1/2=A, 13=B, UNC=C, 2A=D].
Q4) ____ is defined as a twisting action that tends to turn one part or end around a longitudinal axis while the other part or end remains fixed.
A) Compression
B) Extension
C) Tortion
D) Expansion
E) none of the above
Q5) Define pitch as related to thread terminology.
Q6) Define blind hole.
To view all questions and flashcards with answers, click on the resource link above. Page 11
Chapter 10: Reading Sections, Revolutions, and
Conventional Breaks
Available Study Resources on Quizplus for this Chatper
112 Verified Questions
112 Flashcards
Source URL: https://quizplus.com/quiz/4266
Sample Questions
Q1) The cutting plane line for an offset section is generally shown using ________ where it offsets through the staggered features.
Q2) Section lines are shown on all parts of a section, especially thin parts.
A)True
B)False
Q3) Describe how very thin features, less than .06 in. (4 mm) thick, are shown in a sectional view.
Q4) Name and describe the method used to locate sectional views on a sheet other than where the cutting plane lines appear.
Q5) A sectional view established by revolving 90 degrees, in place, into a plane perpendicular to the line of sight, generally used to show the cross section of a part or feature that has consistent shape throughout the length.
A) Removed section
B) Revolved section
C) Aligned section
D) Offset section
E) none of the above
Q6) What are section lines and what are they used for?
Page 12
To view all questions and flashcards with answers, click on the resource link above.
Chapter 11: Reading Geometric Dimensioning and Tolerancing
Available Study Resources on Quizplus for this Chatper
129 Verified Questions
129 Flashcards
Source URL: https://quizplus.com/quiz/4267
Sample Questions
Q1) A feature control frame can include ____.
A) geometric characteristic
B) tolerance zone
C) geometric characteristic tolerance
D) material conditions symbol
E) all of the above
Q2) When the axis of the hole at an extreme angle inside the positional tolerance zone. This is referred to as _________________________.
Q3) When the position tolerance is at MMC, the related datum feature can be ____.
A) RFS
B) MMC
C) LMC
D) all of the above
E) none of the above
Q4) This is the actual feature of the part that is used to establish the datum.
Q5) In form tolerance, circularity is a blanket tolerance that results in a feature lying between two cylinders.
A)True
B)False
To view all questions and flashcards with answers, click on the resource link above. Page 13
Chapter
Available Study Resources on Quizplus for this Chatper
80 Verified Questions
80 Flashcards
Source URL: https://quizplus.com/quiz/4268
Sample Questions
Q1) Which of the following is not a basic type of cam?
A) knife-edge cam
B) plate cam
C) face cam
D) drum cam
E) none of the above
Q2) A cam, a cam shaft, and a hub are all basic components of a cam mechanism.
A)True
B)False
Q3) Some gears have nonintersecting shafts that are at right angles. Which of the following is not in this category?
A) worm gears
B) crossed helical gears
C) bevel gears
D) hypoid gears
E) none of the above
Q4) A complete cam cycle has taken place when the cam has rotated 360°.
A)True
B)False
Q5) What is a cam?
To view all questions and flashcards with answers, click on the resource link above. Page 14
Chapter 13: Reading Precision Sheet Metal Prints
Available Study Resources on Quizplus for this Chatper
66 Verified Questions
66 Flashcards
Source URL: https://quizplus.com/quiz/4269
Sample Questions
Q1) Describe the practice of showing the part in its bent form and in flat pattern on a print.
Q2) Bend transition refers to the change made between the adjacent surfaces at a bend when the edge of one surface extends beyond the edge of the other surface.
A)True
B)False
Q3) The principal plane is the surface from which the bend is formed.
A)True
B)False
Q4) Describe a bend table.
Q5) Bend relief is typically added to a sheet metal part to relieve stress, or the tear, that occurs when a portion of a piece of material is bent.
A)True
B)False
Q6) Sheet metal thickness generally ranges between .03 in. (0.75 mm) and .5 in. (12 mm).
A)True
B)False
Q7) What factors influence the amount of bend allowance?
Page 15
To view all questions and flashcards with answers, click on the resource link above.
Chapter 14: Reading Prints of Working Drawings
Available Study Resources on Quizplus for this Chatper
87 Verified Questions
87 Flashcards
Source URL: https://quizplus.com/quiz/4270
Sample Questions
Q1) What is an engineering change notice?
Q2) The general engineering change elements, terminology, and techniques are similar among companies where the ASME standards are followed.
A)True
B)False
Q3) What is an assembly print?
Q4) Identify the ASME term that is a tabulation of all engineering prints, associated lists, specifications, standards, and sub-data lists related to the item for which the data list applies.
Q5) Each balloon needs to have its own leader line to avoid confusion.
A)True
B)False
Q6) What are standard parts?
Q7) These assemblies can be made from photographs or artistic renderings.
A) pictorial assembly
B) general assembly
C) subassembly
D) detail assembly
E) none of the above
To view all questions and flashcards with answers, click on the resource link above.
Chapter 15: Welding Processes and Reading Welding
Representations
Available Study Resources on Quizplus for this Chatper
93 Verified Questions
93 Flashcards
Source URL: https://quizplus.com/quiz/4271
Sample Questions
Q1) When a weld penetration is specified, the depth of penetration is placed in parentheses and placed to the right of the weld symbol.
A)True
B)False
Q2) Welding sizes are given in either inches or centimeters.
A)True
B)False
Q3) The ____ has a list of materials that generally provides a key to the assembly.
A) welding symbol
B) welding reference
C) welding assembly
D) welding equipment
E) none of the above
Q4) Soldering is done above 450° C and brazing is done below 450° C.
A)True
B)False
Q5) Unless otherwise specified, a weld ___________________________________ the thickness of the parts at the joint.
To view all questions and flashcards with answers, click on the resource link above. Page 17
Q6) ____________________ is a trademark of the Union Carbine Corporation.
Chapter 16: Reading Prints of Pictorial Drawings
Available Study Resources on Quizplus for this Chatper
61 Verified Questions
61 Flashcards
Source URL: https://quizplus.com/quiz/4272
Sample Questions
Q1) Pictorial drawing a form of drawing that shows an object's depth. Three sides of the object can be seen in one view.
A)True
B)False
Q2) Two principal components of a perspective drawing are ____.
A) the location of the station point, and the location of the vanishing point
B) the picture plane, and the vanishing point vertical
C) the horizon line, and the location of the picture plane
D) the eye of the person viewing the object, and the location of the person in relation to the object
E) none of the above
Q3) Only isometric projections are used to create exploded assemblies.
A)True
B)False
Q4) The most realistic type of pictorial illustration is perspective drawing. A)True B)False
Q5) Completely describe an explode assembly and its use.
Q6) What are the most common forms of pictorial drawing used on engineering prints?
Q7) Name the ASME standard for pictorial drawings.
To view all questions and flashcards with answers, click on the resource link above. Page 18
Chapter 17: Reading Electrical Diagrams and Schematics
Available Study Resources on Quizplus for this Chatper
70 Verified Questions
70 Flashcards
Source URL: https://quizplus.com/quiz/4273
Sample Questions
Q1) If A = 3 times 10 to the power of negative 6, and B = 2 times 10 to the power of 5, what is the product of A times B?
A) 6 times 10 to the power of negative 1
B) 6 times 10 to the power of 1
C) 6 times 10 to the power of 11
D) 6 times 10 to the power of 30
E) none of the above
Q2) A ____ is a group of insulated wires put together in one sealed assembly.
A) truck line
B) feed line
C) Multi-conductor
D) substation
E) none of the above
Q3) The placement of identification numbers of electronic components is variable.
A)True
B)False
Q4) A coil is a conductor wound on a form or in a spiral that has inductive properties.
A)True
B)False
To view all questions and flashcards with answers, click on the resource link above. Page 19