Product: MOTOR GRADER
Model: 12M 2 MOTOR GRADER F9M
Configuration: 12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3
Engines for Caterpillar Built Machines Media
Air Cleaner Housing - Remove and Install
Removal Procedure
i06652088
Installation Procedure
This is the sample of the manual
Click on the download link for complete Manual
Product: MOTOR GRADER
Model: 12M 2 MOTOR GRADER F9M
Configuration: 12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3
Engines for Caterpillar Built Machines
Air Compressor - Remove and Install
Removal Procedure
Do not disconnect the air lines until the air pressure in the system is at zero. If hose is disconnected under pressure it can cause personal injury.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.
i06653108
Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.
Dispose of all fluids according to local regulations and mandates.
Note:
Product: MOTOR GRADER
Model: 12M 2 MOTOR GRADER F9M
Configuration: 12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3
Engines for Caterpillar Built Machines Media
i06653681
Air Control Valve - Remove and Install - Control Module, Clean Emissions Module SMCS
Removal Procedure
Installation Procedure
Product: MOTOR GRADER
Model: 12M 2 MOTOR GRADER F9M
Configuration: 12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3
Engines for Caterpillar Built Machines
Media Number -KENR8149-07
Date -01/05/2014
Air Control Valve - Remove and Install
Removal Procedure
Updated -29/05/2014
i05295284
Installation Procedure
Product: MOTOR GRADER
Model: 12M 2 MOTOR GRADER F9M
Configuration: 12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3
Engines for Caterpillar Built Machines
Atmospheric Pressure Sensor - Remove and Install
Removal Procedure
i06653729
Product: MOTOR GRADER
Model: 12M 2 MOTOR GRADER F9M
Configuration: 12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3
Engines for Caterpillar Built Machines Media
Bearing Clearance - Check
Measurement Procedure
i05977048
Note:
Contaminants may cause rapid wear and shortened component life.
Note:
NOTICE
Lead wire, shim stock or a dial bore gauge can damage the bearing surfaces.
Note:
Note:
Note:
Product: MOTOR GRADER
Model: 12M 2 MOTOR GRADER F9M
Configuration: 12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3
Engines for Caterpillar Built Machines Media
Belt Tensioner - Remove and Install
Removal Procedure
i06653775
Product: MOTOR GRADER
Model: 12M 2 MOTOR GRADER F9M
Configuration: 12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3
Engines for Caterpillar Built Machines
Camshaft - Install
Installation Procedure
Required Tools
Tool
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
i07946375
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed or installed.
Note:
This is the sample of the manual
Click on the download link for complete Manual
NOTICE
When installing the camshaft, make sure the number one cylinder is at top center of the compression stroke with the timing bolt installed in the flywheel. The camshaft timing is very important. The timing mark on the camshaft drive gear must line up with the timing mark on the idler gear. Refer to the Specifications Manual for more information.