OVALE / OVALE WIFI AMBIENT TEMPERATURE & POWER REGULATOR CONTROL
Smart Life
INSTALLATION, OPERATING AND USER MANUAL MAY ONLY BE PERFORMED BY QUALIFIED PERSONS
Prior to installing and using the temperature controller, please carefully read this manual and keep it for future reference
1
TABLE OF CONTENTS
1
2
General warnings
......................................................................................................................... 4
1.1
Disclaimer ...............................................................................................................4
1.2
Warranty .................................................................................................................4
1.3
Product compliance ................................................................................................4
1.4
General Warnings ...................................................................................................4
1.5
Safety Warnings
...........................................................................................5
Product presentation ............................................................................................................................... 6 2.1
Functions Description .............................................................................................6
3
Symbols And Glossary ............................................................................................................................ 7
4
Technical Specification Tables .............................................................................................................. 9
5
Installation – Qualified technicians only
.................................................................................. 10
5.1
Before you start ....................................................................................................10
5.2
Towel Rail Warnings .............................................................................................11
5.3
Power supply Warnings ........................................................................................12
5.4
OVALE / OVALE WIFI position ...................................................................................... 12
5.4.1
TOWEL RAIL POSITION .................................................................................................................................... 12
5.4.2
SUPPLY CORD POSITION................................................................................................................................ 14
5.4.3
OVALE / OVALE WIFI REGULATING BOX POSITION ................................................................................ 14
5.5
OVALE / OVALE WIFI installation ........................................................................15
5.5.1
IF OVALE / OVALE WIFI IS NOT CONNECTED TO THE HEATING ELEMENT ..................................... 15
5.5.2
IF OVALE / OVALE WIFI INCL. HEAT. ELEMENT IS NOT CONNECTED TO THE TOWEL RAIL ....... 16
5.6
Cleaning................................................................................................................18
5.7
Uninstalling OVALE / OVALE WIFI .......................................................................18
5.8
Notes for disposal of OVALE / OVALE WIFI valid for the European Union...........18
6
Use and functioning ............................................................................................................................... 19
7
Controller Functions .............................................................................................................................. 20 7.1
OVALE / OVALE WIFI buttons maps ....................................................................20
7.2
First start ...............................................................................................................21
7.3
Standard functions ON-OFF ........................................................................................... 22
7.4
Mode selection ......................................................................................................23
7.5
Mode editing .........................................................................................................23
7.6
Boost mode (OVALE) ...........................................................................................24
7.7
Boost mode (OVALE WIFI) ...................................................................................25
7.8
Weekly program edit (OVALE)..............................................................................26
7.9
Weekly program edit (OVALE WIFI) .....................................................................27 2
7.10 Weekly program view............................................................................................28 7.11 Secondary functions (OVALE) ..............................................................................28 7.11.1
Open window ........................................................................................................................................................ 29
7.11.2
Timing .................................................................................................................................................................... 30
7.11.3
Factory reset ......................................................................................................................................................... 31
7.12 Secondary functions (OVALE WIFI)......................................................................31 7.12.1
Open window ........................................................................................................................................................ 32
7.12.2
Timing .................................................................................................................................................................... 33
7.12.3
Beep mode to enable sound on any button pressure ..................................................................................... 34
7.12.4
OFS (Menu for Temperature Compensation Offset) ...................................................................................... 34
7.12.5
Selecting the unit of measurement (°C/°F)....................................................................................................... 34
7.12.6
Pairing the WIFI control with the device. WIFI Menu...................................................................................... 35
7.12.7
Factory reset ......................................................................................................................................................... 35
7.12.8
Firmware release ................................................................................................................................................. 36
7.13
Lock ....................................................................................................................36
7.14 WIFI pairing Procedure (only for OVALE WIFI) ....................................................36 7.15 SMART LIFE APP LAYOUT .................................................................................41 7.15.1
Overview................................................................................................................................................................ 41
7.15.2
Mode ...................................................................................................................................................................... 41
7.15.3
Boost ...................................................................................................................................................................... 42
7.15.4
Settings – Week Program Mode ........................................................................................................................ 42
8
Maintenance ........................................................................................................................................... 43
9
Diagnostics.............................................................................................................................................. 43
10 Supplied accessories, consumables and spare parts...................................................................... 44 11 Power cable reduction........................................................................................................................... 44
3
1 GENERAL WARNINGS 1.1 Disclaimer The manufacturer declines all responsibility for any inaccuracies in this document due to printing or transcription errors. It reserves the right to make any alterations to its products deemed necessary or useful. The manufacturer will not be held responsible for faults due to incorrect installation.
1.2 Warranty OVALE / OVALE WIFI is guaranteed against defects in materials and/or workmanship for a period of twenty-four (24) months from the date of purchase. The guarantee will not be effective if the faults found are ascribable to the Buyer’s carelessness and/or if the Products have not been used according to their technical specifications and in the event of wrong maintenance by non-authorized engineers, cleaning with unsuitable procedures or materials, improper storage, handling and transport, or any other circumstances that cannot be ascribed to manufacturing defects for which manufacturer is responsible. The guarantee of OVALE / OVALE WIFI is not valid in case of improper use or wrong installation.
1.3 Product compliance APPLICABLE EUROPEAN DIRECTIVES AND STANDARDS Applicable Directives 2014/53/EU Radio Equipment Directive (RED) 2014/35/EU Low Voltage Directive (LVD) 2014/30/EU Electromagnetic Compatibility Directive (EMC) 2011/65/EU RoHS II Directive, Regulation REACH (EC 1907/2006) 2012/19/EU WEEE Directive 2024/1103/EU EcoDesign Electric radiator operation is in full compliance with EN 60335-2-30 The seasonal energy efficiency (ηs) of fixed electric heaters with OVALE / OVALE WIFI, per EU Ecodesign Regulation 2024/1103, is 50.53 %.
1.4 General Warnings •
Read the instructions carefully before installing and using the electronic control (hereinafter referred to as OVALE / OVALE WIFI or appliance) and retain the instructions for future reference.
4
•
•
Installation of OVALE / OVALE WIFI must be performed only by qualified technicians which assume complete responsibility for the definitive installation and consequent good functioning of the product installed. Installation must be compliant with all applicable safety regulations and laws, national, regional, provincial and town council Standards present in force in the Country in which the final product has been installed, as well as the instructions contained in this manual. The Manufacturer cannot be held responsible for the failure to comply with such precautions.
1.5 Safety Warnings • •
• •
•
•
•
• •
•
Children of less than 3 years must be kept away unless continuously supervised. This appliance can be used by children aged from 8 years or over and by persons with reducedphysical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and they understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance. CAUTION — Some parts of this appliance can become hot and may cause burns. Precautions should be taken to ensure that prolonged contact with the el. towel rail cannot occur. Particular care should be taken in confined areas where accidental prolonged contact with the el. towel rail could be more likely to occur. Particular attention has to be given where children and vulnerable people are present. IMPORTANT: In order to disconnect the incoming supply for the purpose of isolation during installation and maintenance it is recommended for the distributor’s service fuse to be withdrawn or the circuit breaker at the distribution board to be switched off whilst work is in progress. Do not install OVALE / OVALE WIFI with an electric heating element not equipped with preset protection devices designed to prevent over-heating of the el. towel rail in abnormal conditions. Do not power OVALE / OVALE WIFI on before it has been completely installed in a properly filled towel rail with the electric heating element recommended by the manufacturer Check that the electricity supply system is connected through an MCB (Magnetothermic Circuit Breaker) and a high sensitivity current differential and overcurrent relay of 30 mA RCCB (Residual Current Circuit Breaker) connected directly to the socket or connection box in use. If OVALE / OVALE WIFI is not fitted with a supply cord with a plug, an omni-pole disconnection from the supply is required, incorporated in the fixed wiring, in accordance with the wiring rules. Switches intended to ensure all-pole disconnection must be directly connected with the supply terminals and must have a contacts distance of at least 3 mm in each pole. The switch intended to ensure all-pole disconnection must be dedicated exclusively to the appliance. 5
• • •
OVALE / OVALE WIFI is suitable for use on an A.C.~ electrical supply. Before installation check that the supply voltage corresponds with that marked on the electronic control. Do not insert metal objects or fingers or any other objects, even temporarily, into the connection areas where OVALE / OVALE WIFI is connected to the towel rail. Avoid direct contact of OVALE / OVALE WIFI with any chemical product or alcohol, including the liquid contained in the towel rail.
2 PRODUCT PRESENTATION OVALE / OVALE WIFI is an electronic ambient temperature controller designed for regulating the thermal power (according to the ambient temperature) of an electric heating element installed in a towel rail configured for drying towels washed in water. Any other use is strictly forbidden. The type of regulation is PI temperature regulation. The controller can be without connectivity (OVALE version) or with WIFI connectivity (OVALE WIFI version). OVALE WIFI use can be remote controlled by Smart Life App to be installed in a smartphone with Apple IOS or Android OS. OVALE / OVALE WIFI has a graphical LCD display with white led backlight that allow a clear information communication to end user.
2.1 Functions Description Main Functions
Description
Comfort
Heating element is drived in order to regulate ambient temperature according to configured set point
Boost
Heating element at full power for a configured limited time
Eco
Heating element is drived in order to regulate ambient temperature according to configured set point
Antifreeze
Heating element is ON when ambient temperature is lower than temperature set value in order to avoid liquid freeze
Weekly Program
Heating element is drived in order to regulate ambient temperature according to configured set point and configured time slot (it is possible configure all the day of the week with up to 1 hour of resolution). Factory Configuration: Heating function is OFF for every time slot of the week..
Aux functions
Description
Open Window
When this option is enabled heating function is stopped if there is a ambient temperature degree with rate higher than 0,4°C / min (2°C within 5 minutes). The heating function is restored if ambient temperature stops to decrease for at least 2 minutes.
Beep selection (WIFI version only)
When this option is enabled, a beep sound is produced at every button pressure.
6
Child Lock
Buttons are disabled. If ON-OFF and Mode Buttons are pressed, buttons are enabled.
Temperature Compensation (WIFI version only)
Temperature Compensation Offset to adjust temperature regulation according to room dimension. Range: -8 to 8°C
Reset
Total reset
Diagnostic functions
Description
Temperature Sensor broken or disconnected
If Temperature Sensor broken or disconnected a warning icon is displayed on LCD display and heating is always OFF.
3 SYMBOLS AND GLOSSARY
Figure 1: Components of OVALE / OVALE WIFI regulating box (front and back view)
Component
Description
Touchscreen interface
Capacitive touchscreen interface displaying current system status (in black or white)
7
Grub screw seat
Position of the grub screw in order to fix OVALE / OVALE WIFI to the Electric heating element connection
Power supply cable
230 V power supply cable with plug or without plug
Figure 2: Electric heating element components
Electric Heating Element Component
Description
Cartridge
Heating part of the electric heating element
Thread
Connection part to be fitted into the towel rail
Fixing part
Necessary part to tighten the electric heating element into the towel rail with a 25 mm wrench
Gasket
O-ring gasket designed to be compressed between the electric heating element connection and the upper plastic part of the OVALE / OVALE WIFI in order to prevent water leakage
Electric heating element connection – Nexus connector
part necessary for coupling with OVALE / OVALE WIFI (and other compatible controllers with Nexus Easy Connect)
8
STANDARD PROVIDED KIT Element O-Ring gasket
Grub screw Allen key
Description 22mm x 1mm gasket designed to allow OVALE / OVALE WIFI coupling with the electric heating element connection part A headless screw having a socket for a hexagon Allen key used to secure the plastic housings of the OVALE / OVALE WIFI onto the electric heating element connection, into the grub screw seat (Figure 1)
4 TECHNICAL SPECIFICATION TABLES OVALE / OVALE WIFI and the electric heating element power must be carefully selected in proportion to towel rail size and thermal output. To select OVALE / OVALE WIFI and the heating element electrical power, please refer to the towel rail manufacturer instructions, when a certification related to the complete system (according to EN 60335-2-30) issued by an European recognized institute (like SEMKO, VDE, IMQ…) is available. The installer shall verify that OVALE / OVALE WIFI System operates in conformity with Table 2. Electric heating element Power (W)
400
600
800
1000
1200
Length (mm)
480
680
820
980
1150
Table 1
OVALE / OVALE WIFI Power supply
230 V / 50 Hz
Electric Heating element power
400 ÷ 1200 W
Insulation class
Class I
Colours and finishing
White or chrome
Touch interface display
White or black
Dimensions
140 x 68 x 64 mm 9
Water protection rating
IPX4
Maximum altitude above sea level
2000m
Operating ambient temperature
0°C ÷ 40°C
Storage temperature
-20°C ÷ 70°C
Max Humidity Level
RH 85% at 25°C (without condensation) Table 2
5 INSTALLATION – QUALIFIED TECHNICIANS ONLY ALL ELECTRICAL INSTALLATION WORK MUST BE CARRIED OUT BY A QUALIFIED ELECTRICIAN Read the general warnings and safety warnings before installation. IMPORTANT: Always disconnect the electricity supply from the mains during installation and maintenance. It is recommended that the fuse is withdrawn, or circuit breaker switched off at the distribution board while work is in progress (turning off the switch is not sufficient). During installation, de-installation and maintenance, ensure working place safety until the operation is completed.
5.1 Before you start • • • •
•
•
Avoid collisions during the handling. Do not deform OVALE / OVALE WIFI. Avoid the contact of cables and of parts of the OVALE / OVALE WIFI with sharping corners and do not cause squashing. Do not subject the cables to traction. Do not apply concentrated pressures on the OVALE / OVALE WIFI surface. Any contact between plastic parts of OVALE / OVALE WIFI and chemical products or alcohol (including the water or the mixture water+ glycol inside the tower rail) must be avoided. Check the pack to ensure you have all of the parts listed at paragraph 3 with no visible signs of damage. Make sure that OVALE / OVALE WIFI parts are completely dry and have no defects. If any of the part is missing or appears damaged, you should return the device to the point of purchase. Check that you have the correct size of electric heating element and of OVALE / OVALE WIFI for your towel rail. It is essential that the correct sized electric heating element and OVALE are installed in line with the recommendation stated on the packaging or instruction of your towel rail CERTIFIED BY A EUROPEAN 10
• • • •
RECOGNISED APPROVAL INSTITUTE. IF YOU ARE NOT SURE OF THAT, PLEASE REFER TO CONTACTS SECTION. When you are ready to start, make sure that you have the right tools at hand, plenty of space and a clean dry area for assembly. Installation must be carried out in accordance with current standards and laws in force in the country in which the system is installed. Before installation, never switch the OVALE / OVALE WIFI on to verify functioning effectiveness. Don’t use the OVALE / OVALE WIFI regulating box to lean the electrical towel rail on the floor as you can damage the plastic housing and water can penetrate inside with a risk of electrical shock.
5.2 Towel Rail Warnings • • • •
•
• •
•
The electric radiator with regulator use is intended only for heating rooms in the home. Any other use is forbidden. The heating element must be fitted in the towel rail before mounting the rail to the wall. The towel rail has to be mounted parallel to the wall using the brackets recommended by the towel rail manufacturer. It is recommended to use in any installation (Electric only and Dual fuel) a self relief pressure valve (like a 3 Bar valve) on the top part of the rail in the opposite side where the OVALE / OVALE WIFI is installed. In case of valve intervention, it is quite normal for liquid relief and water excess to possibly reach the floor. Please, take this aspect into consideration. In Electric only OVALE / OVALE WIFI installation, fill the towel rail with certain percentage of water according to the towel rail manufacturer instructions. In case of missing instructions, we recommend to fill the towel rail approximately 90% with approximately 90% pure water and glycol mixture. In Electric only OVALE / OVALE WIFI installation the towel rail must have a sufficient air gap to allow for water expansion. Making sure that the OVALE / OVALE WIFI heating element is completely immersed in water.In case of Dual fuel installation, a T-piece of 40mm maximum length (male thread excluded) is required: we recommend to wrap a small quantity of PTFE tape around the heating element thread and the T-piece thread. All metallic parts of the electrical towel rail fitted with OVALE / OVALE WIFI and powered must not exceed the temperature limits according to the applicable standard also in case of OVALE / OVALE WIFI continuously powering the electric heating element. For all other aspects, refer to EN 60335-1 and EN 60335-2-30.
11
5.3 Power supply Warnings • • •
• •
Do not connect OVALE / OVALE WIFI to the power supply until the installation into a properly filled towel rail is completed. Make sure that the power lines are appropriate for the load required according to technical specification tables (see part 4). Class I OVALE / OVALE WIFI (with yellow-green wire or earthed plug) must ONLY be connected to sockets or connector blocks with earthed contacts according to national standards and wiring regulations in force Protect the electricity supply with an RCCB (Residual Current Circuit Breaker) device. The electrical heating element must be connected to a suitable electricity supply by way of the cable provided. This should be via a fused spur in accordance with the IEE Wiring Regulations. If sited in the bathroom, the Fused Connection Unit must be located out of reach of persons using the basin, shower or bath. If in doubt, consult a qualified electrician.
OVALE / OVALE WIFI supply cord WITH plug The socket and electricity supply must be appropriate for the required power. Do not use extensions. The socket must be compatible with the OVALE / OVALE WIFI supply cord plug. Do not use adapters.
5.4 OVALE / OVALE WIFI position OVALE / OVALE WIFI must be fitted into the towel rail BEFORE mounting the towel rail to the wall.
5.4.1 TOWEL RAIL POSITION • • • •
The towel rail must be installed in a completely vertical wall. The towel rail has to be mounted parallel to the wall using the brackets recommended by the towel rail manufacturer. OVALE / OVALE WIFI must not be within reach of people using the basin, shower or bath. The radiator equipped with the OVALE / OVALE WIFI controller must be located at least in bathroom zone 2 in accordance with the IP protection level and applicable electrical regulations (Zone definition according to IEC 60364-7-701 – see Figure 3). In 12
• • •
case of doubt about the correct installation zone, refer to the relevant public institution. Do not install OVALE / OVALE WIFI into a towel rail fitted in ZONE 0 or ZONE 1. Other locations are the responsibility of the installer and must be properly tested. The IPX4 protection level for the controller + heating element assembly is only ensured in the case of complete and professional installation.
Figure 3
13
5.4.2 SUPPLY CORD POSITION The supply cord must be connected to a proper socket or to a non-switched fused spur (without an intermediate plug for OVALE / OVALE WIFI supplied without plug) which must be at least 25 cm from the floor according to the wiring regulations in force in the country where the installation is carried out. Figure 4 shows examples of positioning of the system.
Figure 4 OVALE / OVALE WIFI positioning
5.4.3 OVALE / OVALE WIFI REGULATING BOX POSITION • •
•
OVALE / OVALE WIFI must only be fitted vertically in the bottom part of the towel rail. Electrical towel rail must NOT be installed with the OVALE / OVALE WIFI regulating box located at the top. This can seriously damage the control box and create a dangerous situation with a risk of fire. OVALE / OVALE WIFI must be installed at distance of 40 mm (minimum) and 80 mm (maximum) from the wall. Figure 5 shows the optimal positions for the OVALE / OVALE WIFI.
Figure 5 OVALE / OVALE WIFI positioning
14
5.5 OVALE / OVALE WIFI installation ATTENTION! Be careful when handling the regulator, especially when putting it on! 5.5.1 IF OVALE / OVALE WIFI IS NOT CONNECTED TO THE HEATING ELEMENT ELECTRIC ONLY 1. OVALE / OVALE WIFI’S CONNECTION AND COUPLING a. Insert OVALE / OVALE WIFI into the electric heating element connection, applying slight pressure until OVALE / OVALE WIFI is fully inserted. b. Keep OVALE / OVALE WIFI pressed against the heating element in the towel rail and insert the provided grub screw into its spot; make sure there is no room between the device and the electric heating element fixing part (see part 3).
2. GRUB SCREW INSERTION a. Keeping OVALE / OVALE WIFI pressed against the heating element in the towel rail, make sure the grub screw is in its right positioning spot (grub screw seat) as shown in figure below. b. Using the provided Allen key tighten the grub screw until it comes into contact and it is fully inserted in its spot, so that the OVALE / OVALE WIFI is securely fixed to the electric heating element and the O-ring gasket is well in contact with both surfaces c. Make sure the grub screw is NOT in other wrong positions by checking the alignment with the back of OVALE / OVALE WIFI, as shown in figure below.
15
3. TOWEL RAIL INSTALLATION
If the display is facing the wall after tightening the heater, always adjust the heating element by turning it anti-clockwise with the 25mm spanner. The seal is designed to adjust to a certain amount of releasing without starting to leak. •
Install properly the electrified towel rail with the OVALE / OVALE WIFI into the wall according to towel rail manufacturer instructions (See part 5.2).
4. CONNECTION TO THE MAINS a. Connect the OVALE / OVALE WIFI cable to the mains power according to current wiring regulations in force in the country where the product is installed. Make sure that the power lines are appropriate for the load required. b. Check electric strength on the appliance after fitting OVALE / OVALE WIFI to the electric towel rail according to the instructions in Appendix A of EN60335-1: “Routine tests”. c. In case of Class I controls, check earthing continuity on the appliance after fitting OVALE / OVALE WIFI to the electric towel rail according to the instructions in Appendix A of EN60335-1: “Routine tests”.
5.5.2 IF OVALE / OVALE WIFI INCL. HEAT. ELEMENT IS NOT CONNECTED TO THE TOWEL RAIL DUEL-FUEL
16
VERIFICATIONS BEFORE INSTALLATION • Check the package delivery. • The delivery includes a radiator, a heating element with a protected Nexus connector and a OVALE / OVALE WIFI controller. • The heating element is pre-prepared in the radiator bus, it is not properly installed. • Carefully unscrew it and prepare it for proper installation. • Switch off the mains. • Do not connect OVALE / OVALE WIFI to the power supply until the installation into a properly filled towel rail is completed. • Make sure that the towel rail can have the OVALE / OVALE WIFI on the bottom side (Figure 5). • If the heating element or the controller is damaged, do not continue with the installation, please contact the seller.
INSTALLING THE HEATING ELEMENT IN THE TOWEL RAIL a. Unscrew the heating element from the towel rail with a light rotary movement. Remove the Nexus connector cover. b. Insert the supplied OVALE / OVALE WIFI O-ring gasket from the bottom over the heating element in the reserved space. In order to minimize the risk for leakage it is recommended to use a PTFE tape or similar product to prevent leakage. c. Insert the tip of the heating element into the bottom hole of the towel rail and make sure to select the female ½” GAS thread.). d. Insert the heating element all the way in the upside down radiator and screw in the heating element using a 25 mm wrench (not included). In case of ‘Dual fuel’ installation, a T-piece of 40 mm maximum length (male thread excluded) is sometimes required. Insert the T-piece in the heating element, screw and tighten it firmly. Do not use tools.
17
Ventil 3 bar
WHEN THE HEATING ELEMENT IS CONNECTED TO THE TOWEL RAIL, GO TO 5.5.1
5.6 Cleaning To clean OVALE / OVALE WIFI, use only a dry and clean soft cloth. Make small locally round movements. Apply a light pressure especially to the chrome plastic surfaces to avoid potential scratches. Do not clean OVALE / OVALE WIFI with aggressive products. Do not wet OVALE / OVALE WIFI in an attempt to clean it. Do not immerse in water. When cleaning OVALE / OVALE WIFI, it must be disconnected from the power supply.
5.7 Uninstalling OVALE / OVALE WIFI ALL ELECTRICAL WORK SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN. Do not touch the metallic parts of OVALE / OVALE WIFI if it is powered; before maintenance and de-installation operation wait the necessary time to ensure it is cold after it is switched off. During installation, de-installation and maintenance, ensure working place safety until the operation is completed.
5.8 Notes for disposal of OVALE / OVALE WIFI valid for the European Union The crossed-out wheeled-bin symbol on the towel rail to which OVALE / OVALE WIFI is installed, reminds you that in the European Union all electrical and electronic products and batteries must be taken to separate collection at the end of their working life. Do not dispose of these products as unsorted municipal waste. Return the products to collection to prevent possible harm to the 18
environment or human health from uncontrolled waste disposal and to promote the sustainable reuse of material resources. Collection information is available from the product retailer, local waste authorities or national producer responsibility organizations. For more information, see product country-specific information.
6 USE AND FUNCTIONING All uses different from the ones described in this section are to be intended as improper usage. In case of doubts refer to the seller. • The electrical towel rail with regulator is intended only for heating rooms in the home. Any other use is forbidden • OVALE / OVALE WIFI is intended to be used and installed into a towel rail. Any other use is strictly forbidden and potentially dangerous. • do not switch on OVALE / OVALE WIFI unless the heating element is properly immersed in the liquid inside the towel rail. • OVALE / OVALE WIFI is intended to work only if the electric heating element connected to OVALE / OVALE WIFI and fitted into the towel rail - is completely immersed in the liquid (water) inside the towel rail. • OVALE / OVALE WIFI is designed for use with water or water+glycol filled towel rails. • Do not use OVALE / OVALE WIFI before it has been completely and correctly installed. If OVALE / OVALE WIFI is not firmly fixed to the towel rail, disconnect the mains turning off the circuit breaker switch and contact the manufacturer in order to avoid hazard. • Do not cut the power supply cable to stop regulation or to switch OVALE / OVALE WIFI OFF. • Once connected to the heating element, OVALE / OVALE WIFI regulating box MUST NOT be disconnected from the heating element. • Do not cover OVALE / OVALE WIFI, even partially, even temporarily.
19
7 CONTROLLER FUNCTIONS 7.1 OVALE / OVALE WIFI buttons maps
Short press Long press
20
7.2 First start First start
Set Hour, Minute and Day.
21
Note: For OVALE WIFI version, if the device is just paired with APP after this procedure time and date will be automatically updated with time and date from internet.
7.3 Standard functions ON-OFF Display backlight
Tap any button one time to turn on the display from the stand-by mode (display off). Display will light on.
Backlight for the display: off after 5 second and on when a button is touched.
ON
Backlight on: Tap ON-OFF button to switch on the controller. Backlight off: Tap any button to switch on the backlight then tap ON-OFF button to switch on the controller.
OFF
Backlight on: Tap ON-OFF button to switch off the controller. Backlight off: Tap any button to switch on the backlight then tap ON-OFF button to switch off the controller.
22
7.4 Mode selection Display backlight
Tap any button one time to turn on the display from the stand-by mode (display off). Display will light on.
ON
Tap ON-OFF button to switch on the controller
Mode button
To switch between the operating modes.
Mode
Temperature setting (OVALE)
Temperature setting (OVALE WIFI)
Comfort
17-30 °C
15-28 °C
ECO
14-19 °C
12-22 °C
Antifreeze
7-15 °C
4-15 °C
7.5 Mode editing Display backlight
Tap any button one time to turn on the display from the stand-by mode (display off). Display will light on.
ON
Tap ON-OFF button to switch on the controller
23
Mode button
To switch between the operating modes.
SELECT the mode (comfort / eco / antifreeze) you want to edit as shown in mode selection
7.6 Boost mode (OVALE) Display backlight
Tap any button one time to turn on the display from the stand-by mode (display off). Display will light on.
ON
Tap ON-OFF button to switch on the controller
Boost / Dryer
Select Boost in order to work at maximum heating level. Tap > or < to customize the time. After the time selected the controller will automatically stop heating and continue to the previous mode.
Time setting: From 60 minutes to 240 minutes
24
7.7 Boost mode (OVALE WIFI) Display backlight
Tap any button one time to turn on the display from the stand-by mode (display off). Display will light on.
ON
Tap ON-OFF button to switch on the controller
Boost / Dryer
Select Boost in order to work at maximum heating level. Tap Boost mode to customize the time. After the time selected the controller will automatically stop heating and continue to the previous mode.
Time setting: From 30 minutes to 3 hours (0:30 – 1:00 – 2:00 – 3:00)
25
7.8 Weekly program edit (OVALE) Display backlight
Tap any button one time to turn on the display from the stand-by mode (display off). Display will light on.
ON
Tap ON-OFF button to switch on the controller
Mode button
Tap mode button to reach the operating modes Weekly Program
If you don't press any button for 3 minutes the timing process program will exit without saving. Temperature range: 17–30 °C. To save your changes please follow the steps until the last day of the week with the 24 complete hours.
26
Note: IIn the event of a 230 V power failure lasting <1 second, the set values are retained in memory. Otherwise, the time must be reset, and the controller will switch to standby mode.
7.9 Weekly program edit (OVALE WIFI) Display backlight
Tap any button one time to turn on the display from the stand-by mode (display off). Display will light on.
ON
Tap ON-OFF button to switch on the controller
Mode button
Tap mode button to reach the operating modes Weekly Program
If you don't press any button for 3 minutes the timing process program will exit without saving. At first program, after 3 seconds noP appears to indicate no weekly program is set. Settings using modes: Comfort /Eco / Anti-freeze/ Off. To save your changes please follow the steps until the last day of the week with the 24 complete hours. NOTE: To have the same program for more days tap the button Increase day.
27
Note: In the event of a 230 V power failure, the controller switches to standby mode. The set values, including the time, are retained in memory..
7.10 Weekly program view Display backlight
Tap any button one time to turn on the display from the stand-by mode (display off). Display will light on.
ON
Tap ON-OFF button to switch on the controller
Mode button
Tap mode button to reach the operating modes Weekly Program
7.11 Secondary functions (OVALE) Display backlight
Mode button
Tap any button one time to turn ON the display from the stand-by mode (display off). Display will light ON. To switch between the secondary functions.
Long press the mode (Open window / Timing / Application / Temperature display / Factory reset) you want to edit as shown in next points
28
7.11.1
Open window
29
7.11.2
Timing
30
7.11.3
Factory reset
7.12 Secondary functions (OVALE WIFI) Display backlight
Mode button
Tap any button one time to turn ON the display from the stand-by mode (display off). Display will light ON. To switch between the secondary functions.
Long press the mode (Open Window / Timing / Beep / Offset / App / Factory reset/ Firmware release) you want to edit as shown in next points
31
7.12.1
Open window
32
7.12.2
Timing
33
7.12.3
Beep mode to enable sound on any button pressure
7.12.4
OFS (Menu for Temperature Compensation Offset)
7.12.5
Selecting the unit of measurement (°C/°F) (Not displayed if OVALE WIFI is paired with App)
34
7.12.6
Pairing the WIFI control with the device. WIFI Menu.
7.12.7
Factory reset
35
7.12.8
Firmware release To show the current software release (Only for SL+OTA label)
7.13 Lock Lock function
Disable all the buttons.
Long press the ON/OFF button while in Comfort / Eco / Antifreeze / Weekly Pr. mode to activate the lock function. In the case of the OVALE WIFI version, also in On/Off mode.
7.14 WIFI pairing Procedure (only for OVALE WIFI) WIFI function
OVALE WIFI product can be remote controlled using the App through the WIFI connection.
Connection with smart device via 2.4 GHz WIFI
36
1. Assure your smartphone Operating System (OS) is updated to last OS release available by store. 2. Scan the QR code to download the APP “SMART LIFE” in your smartphone with iOS or Android OS.
3. Create your own Smart Life Account with email and password. 4. Allow Smart Life App to access to the following functions:
37
5. In the OVALE WIFI select to APP submenu and press the “confirm” button to starts countdown
6. Open Smart Life App and click on “+” to add device
38
7. Wait until the device is found (OVALE WIFI icon appears when the device is found)
OVALE WIFI
8. Click on OVALE WIFI icon and then enter select WIFI network and insert selected WIFI password
39
9. Wait until the device is added
10. Click on Done Button to go directly in the OVALE WIFI App
40
7.15 SMART LIFE APP LAYOUT 7.15.1
Overview
Note: to enter in the main menu press “switch” button.
7.15.2
Mode
41
7.15.3
Boost
7.15.4
Settings – Week Program Mode
42
NOTE: In the Week Program Mode scheduling after having selected the timing on the menu assignment please don’t’ use Manual or Weekly Program. If you accidentally use them the regulation is identical to Comfort Mode.
8 MAINTENANCE Switch off the mains before any installation, de-installation or maintenance operation on OVALE / OVALE WIFI. • •
•
.
During installation, de-installation and maintenance, ensure working place safety until the operation is completed. Do not touch the metallic parts of OVALE / OVALE WIFI if it is powered; before maintenance and de-installation operation wait the necessary time to ensure it is cold after it is switched off. IMPORTANT: Always disconnect the electricity supply from the mains during installation and maintenance. It is recommended that the fuse is withdrawn or circuit breaker switched off at the distribution board while work is in progress (turning off the switch is not sufficient). Never try to modify or repair the OVALE / OVALE WIFI in any of its parts by yourself. Never try to remove any part of the OVALE / OVALE WIFI as water can penetrate inside the regulation box resulting in a risk of electrical shock. Never knock the OVALE / OVALE WIFI against anything. Handle with extreme care during every operation and never leave it in wet areas.
9 DIAGNOSTICS Description of fault
Operations
OVALE / OVALE WIFI regulation mode is selected
The product must be replaced, please contact seller.
LEDs are ON but the towel rail doesn’t heat
Wait for 2 hours If the situation doesn’t change, contact the seller
In case of anomalous or strange working condition or if OVALE / OVALE WIFI has visible signs of damage
Disconnect the OVALE / OVALE WIFI from the mains switch off the omnipolar switch immediately
at maximum power level and the towel rail doesn’t heat at all
43
send OVALE / OVALE WIFI to the seller for investigation or replacement.
10 SUPPLIED ACCESSORIES, CONSUMABLES AND SPARE PARTS In the event of malfunctioning or damage, the whole OVALE / OVALE WIFI must be replaced. No spare parts are available. If the OVALE / OVALE WIFI regulating box shows some plastic cracks, please contact the seller for replacement. OVALE / OVALE WIFI power supply cable cannot be repaired. If it is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. Never try to modify or repair the OVALE / OVALE WIFI in any of its parts by yourself. Never try to remove any part of the OVALE / OVALE WIFI as water can penetrate inside the regulation box resulting in a risk of electrical shock. Never knock the OVALE / OVALE WIFI against anything. Handle with extreme care during every operation and never leave it in wet areas.
11 POWER CABLE REDUCTION The length of the power supply cable OVALE / OVALE WIFI can be reduced to allow its direct installation in a wall box or connection to a terminal designed for the cable, i.e. it is certified and rated for the given type of installation (e.g. an electric plug with an integrated switch). CAUTION! The cable must extend at least 300 mm from the inlet to the heating unit, the thermostat receiver or regulator (according to the equipment installed) after it has been cut. No warranty claim or repair will be accepted, including defects not related to the shortening of the cable, if the length of the cable is less than 300 mm. The reduction may only be carried out by a person with the appropriate electrical expertise! The external insulation of the cable and the insulation of individual conductors must remain intact. Avoid using cables with broken insulation. All connections/wiring must be in compliance with the legislation of the country where the installation is performed, as well as with the rules for use in specific environments (e.g. bathrooms), the IEC 60364-7-701 standard in particular. In this case, the rated degree of protection, IPX4, as declared by the manufacturer of the product, will not apply to the reduced end of the cable and/or any terminal.
44
The wiring of Class I equipment is as follows: Brown (black): Blue: Yellow-green:
L N PE
phase 230 V / 50 Hz neutral conductor protective conductor (earth)
The manufacturer assumes no responsibility for any damage to the equipment or personal injury caused by improper installation of the cable, reversed polarity, insulation damage or any other intervention, connection or wiring that is not in compliance with the applicable regulations.
CONTACT DETAILS Plieger B.V. Koxampseweg 6 Zaltbommel www.plieger.nl
06/26 800341381_EN_QR 45