Compatibility Overview
3D PRINTER
SOL, DENTIQ, Freeshape 120 G3
CURING UNIT
OtoFlash by NK-Optik
2 x 2000 Flashes
HiLite Power by Kulzer 2 x 180 s
SEGA
MAX UV, PRO 4K D4K, Micro Plus XL
3Delite, 3Demax
CURIE by Ackuretta
2 x 3 min | T:6 P:16 D:10 B:ON
Cure by DentaFab 1 x 10 min
Photopol by Dentalfarm 2 x 4 min with vacuum
BB Compact by Meccatronicore
1 x 6 min | Power 100% | Temp 20°C / 68°F | Plate on top rail
Alpha Prime
NextDent 5100, LCD1
Distributed by NextDent resellers (barcode necessary)
LC-3DPrint Box by NextDent 1 x 30 min NextDent Cure by NextDent 1 x 10 min
Medical One
Shape 1+ Dental
AccuFab-L4D/L4K, AccuFab-D1s
NBEE
SF150, SF350, SF650
UltraCraft Chairside, UltraCraft A2D, UltraCraft A2D 4K : 07/2023 |
D600242 |
RS cure by Rapidshape 1 x 6 min
Fab Cure by Shining 2 x 10 min
Fab Cure 2 by Shining 2 x 5 min (without heater)
UltraCraft PCU 3.0 by HeyGears 2 x 3 min 40% power UltraCraft AirCure by HeyGears 2 x 3 min 10% power
Medical CW One by Prusa
2 x 10 min
ShapeCure by RayShape 2 x 10 min (no heat necessary)
U Cure by UNIZ 2 x 2 min
1/2
Class
Medical
Sonic 4K 2022, Sonic 4K XL 2022 D20 II, D30 II, D40 II, D10+, D20+ cartridge, D20+, D30+, D50+ | Class II Medical
IIa
Device (EU)
Device (US)
Cure by Phrozen 2 x 5 min
™
More information at saremco.ch/en/downloads/instruction-for-use/ Edited 1 1 1 6 1 1 1 4 8 3 2 2 2 7 14 13 12 11 10 9 9 5 4 8 6 9 5 3 2 10 14 7 13 12 1 11
Officially Validated Devices
saremco print
Good to Know
saremco print
WAYS OF CLEANING
REACH THE FINAL COLOR
RECOMMENDED AUTOCLAVE
RECOMMENDED | EASIEST WAY SAREMCO PRINT CLEANING CONCENTRATE
Mix the concentrate to obtain a cleaning liquid. Cleaning in ultrasonic bath (2 x 3 minutes) More product information about saremco print CLEANING CONCENTRATE can be found on our website.
5 minutes Autoclave (134°C / 276 2°F), to accelerate color finalization. or
RECOMMENDED WATER BATH
at least 2 minutes in boiling water (100°C / 212°F), to accelerate color finalization
OPTIONAL | BEST RESULTS CLEANING BY HAND
Remove excess resin from print object using a brush and cloths with a small amount of IPA (96%). Dry the surface and inside of the print object with compressed clean air
RECOMMENDED POLIMERIZATION LAMP
Expose each side of the print object for 2 x 20 seconds at full power
Recommended polimerization devices for light-curing materials such as OtoFlash and HiLite Power reach a wavelength range of 320 - 500nm Other LED polimerization devices mentioned before, may do not reach the upper wavelength range and do not completely finish the esthetic color finalization process (no influence on the physical properties of the material)
To accelerate the color finalization, it is recommended to place the print object for 5 minutes into an autoclave (134°C / 276 8°F) or in boiling water (100°C / 212°F) for at least 2 minutes A polimerization lamp such as a Bluephase® G2 from Ivoclar Vivadent can be used optionally (2 x 20 s full power on the print object per side) to cover the higher wavelength ranges (up to 500nm) Please note: This compatibility overview does not replace the instructions for use Please read the instructions for use carefully
*Data Protection Disclaimer
By scanning the QR code, you acknowledge and agree that you will be redirected to YouTube and will be subject to their privacy policy Please review YouTube‘s privacy policy before proceeding
: 07/2023 | D600242 | Class IIa Medical Device (EU) | Class II Medical Device (US)
2/2
™
*
More information at saremco.ch/en/downloads/instruction-for-use/ Edited Scan for Youtube Demo Scan for Youtube Demo Scan for Youtube Demo* Scan for Youtube Demo* Mixing Protocol Cleaning Protocol Available from Q32023 2‘ D E NTAL E X PERIE N C E D E NTAL E X PERIE N C E over 30 YEARS