Let’s build the
Celeste Wall Light 5
35
SEMBL
Y
A
S
M I N UT E
3
SKU 16201
Scan me! Free Lifetime Warranty 25-0906-CN
Ok, let’s get rolling
What’s included Description
Qty
1
Fixture Assembly
1
2
Lamp Shade
1
3
Stem (6”)
1
4
Stem with threaded extension (12”)
1
Estimated time for assembly
5
Stem (12”)
1
35:00
A
Mounting Plate
1
B
M4*15mm Fixture Screws
4
C
M4*25mm Junction Box Screws
2
D
Wire Connectors
1
This should be easy, just follow our instructions and you will be back to Netflix in no time.
What you need •
Your favorite snack or energy bar (Save the bubbly for once your fixture is safely installed!)
E
M3.5x35mm Screws
3
•
Use the packaging carton as a working surface to prevent product damage during assembly
F
Non-Dry Wall Anchors
3
G
Mounting Unit
1
H
Dry Wall Anchors
3
•
Phillips head screwdriver
•
Pencil
I
Plastic Plug
1
•
Electric Drill
J
Cord Sleeve
1
•
1/4” Drill bit (for non-drywall)
K
M3.5X50mm Screws
3
•
5/16” Drill bit (for drywall)
•
Mallet or hammer (for plug-in installation)
L
M10*25mm Thread Insert
2
M
Allen Key
1 3
Scan me!
Toll-free at 1-866-619-1004 Help@nathanjames.com Nathanjames.com/help
Free Lifetime Warranty
2
Safety first, fun later Safe use of this product starts with you.
Do not modify the structure of this product in any way.
Use this light fixture responsibly with the primary concern for your safety. Follow assembly instructions carefully and inspect product upon receipt and each use.
Our products have been tested to meet specific safety measures as they were originally intended to be sold. Any modifications will present the risk of creating significant safety issues which Nathan James will not be responsible for.
Nathan James and its parent companies cannot be held legally responsible for any injuries or death resulted from failure to follow instructions or improper use of this product.
Proper use DO NOT
use for commercial purposes
DO NOT
leave spilled liquid on fixture
DO NOT
use light fixture if damaged
DO NOT
make temporary repairs
DO NOT
use outdoors
WARNING: RISK OF ELECTRIC SHOCK
WARNING Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have occurred during shipping. If there is a defect in the wire, do not attempt installation. Please reach out to our Customer Happiness team at help@nathanjames.com or 1-866-619-1004
Before starting the installation, disconnect the power by turning off the circuit breaker or by removing the appropriate fuse at the fuse box. Turning the power off at the switch is NOT SUFFICIENT to prevent electrical shock. PLEASE CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL QUESTIONS.
3
The goods
1
3
4
5
IMPORTANT 1. Do not tighten bolts / screws completely until all bolts / screws are lined up and inserted into holes. 2. Do not over tighten screws and bolts to avoid stripping. 3. Please use hand tools to assemble this product. Do not use power tools.
4
2
The goods cont.
A
B
E
H
D
C
G
F
J
I
L
K
5
M
Pre-Installation •
Read all instructions prior to beginning assembly.
•
To avoid damaging this product, assemble it on a soft, non-abrasive surface such as carpet or cardboard.
•
Keep the receipt and these instructions for proof of purchase.
•
Suggested Bulb: A19 LED 60 Watt Equivalent | E26 Medium Base | Dimmable
•
Fixture Max Wattage: 60W
Plug-in option
The following steps 1–16 are intended for wall mounted plug-in use only. Skip ahead to page 18 for directions on how to hardwire this light into your existing electrical box.
Step 1 It’s as easy as it looks! Separate the Fixture Assembly (1) from the Mounting Unit (G) by removing the Fixture Screws (B).
1
G
B
B
B B
B
B
6
B
B
Step 2 You’ve successfully cleared the path by removing the mounting unit. Now, behold the wire compartment!
1 ST
1
2ND L
Clear with “L”(Hot)
Carefully raise the flap on the wire connector to release the clear wire. Repeat this step on the second connect so that both clear wires have been removed and the black and white wires remain attached to the Fixture Assembly (1). Once the wires have been disconnected, prepare yourself for the grand unraveling! Untie the knot that has kept the two clear wires intertwined.
Black 1
1 ST 2ND Clear(Neutral)
2
White
3
7
Step 3 Voila! With the knot untied, it’s time for you to take charge. Carefully pull the cord through the bottom hole of the Fixture Assembly (1), giving it a gentle tug to guide it. Watch as it follows your lead, making its way out.
1
7
Step 4 Now comes the fun part: deciding how tall your fixture should be. You have the power to choose the perfect length by mixing and matching various Stem lengths or leaving some out completely.
L
Once you’ve settled on the ideal length, start by placing the Cord Sleeve (J) onto cord. After that, twist on the Stems without connecting them just yet. Once you’ve got all the Stems in place, add the Thread Insert (L) to the end of the tubes.
Helpful Tip: Braiding the wire cores together then rotating the tube while threading the cord through will make things go a little more smoothly.
3
L
3
J
12” cord sleeve:
L
5
J
18” cord sleeve:
L
3
5
J
24” cord sleeve:
L
4
5
J
30” cord sleeve:
L
3
L
4
L
3
3
L
J
5
J
5
J
4
5
J
4
5
J
L
L
J
5
6” cord sleeve:
L
L
4
L
3
8
5
J
Step 5 Take the wires and guide them back through the hole at the bottom of the Fixture Assembly (1) - it’s like threading a needle.
1
Step 6 Time to tie a knot and secure those wires like a pro! Inside the electrical compartment create a knot that will hold the wires securely in place. Leave about 70 mm of wire from the knot to the end. This clever maneuver ensures you’ll have enough space to reconnect the wires to their initial spot under the flaps.
1
1
70M
M
2
It’s all about keeping things organized and making sure your wires feel right at home!
3
9
7
Step 7 To proceed, open the flaps once again. Insert the clear neutral wire alongside the white wire. Place the hot wire (marked with an L) next to the black wire.
2ND 1ST
1
L Clear with “L”(Hot) Black
2ND
1ST
Clear(Neutral) White
10
Step 8 Attach the M10*25mm Thread Insert (L) to the first Stem over the cord. Turn it in a counterclockwise direction until it is securely fastened.
L
1
L L
L
11
Step 9 Now, it’s time to bring all the Stems together in perfect harmony! Let’s start from the top.
1
Hold onto the first tube that’s already connected and get ready to attach the second one. Carefully rotate the second Stem counterclockwise onto the first one, just like fitting puzzle pieces together. Repeat this process for the rest of the tubes, linking them in the same way.
3 4
5 J
12
Step 10 With the Mounting Unit (G) as a guide, use a level and pencil to mark within the holes where you want it on the wall.
G
Step 11 Using a drill, the paper drill bit, and the reference marks from the previous step, drill 3 holes into the wall. Important note: Non-drywall = 1/4” Drill bit Drywall = 5/16” Drill bit
x3
Step 12 Tap the Wall Anchors (F) or (H) into place in the new holes you just drilled. You may be able to push them into place with your thumbs.
F H
Important note: Non-drywall = 1/4” Drill bit Drywall = 5/16” Drill bit
x3
13
Step 13 To attach the Mounting Unit (G) to the wall, you can either use the (K) or (E) Screws, depending on the type of wall. Important note: E for Non-drywall anchors K for Drywall anchors
G K E
14
Step 14 Attach Fixture Assembly (1) to Mounting Unit (G). Align the holes on the fixture with the exposed screws. Tighten them securely using the Fixture Screws (B). Turn the Fixture Screws (B) in a counterclockwise direction. Unscrew the collar fitting from the Fixture Assembly (1) by turning it clockwise until it comes off.
1
B
B
B
B
G
15
Step 15 Install the Lamp Shade (2) by setting it in place with the shade collar fitting that you removed in step 14. Thread the collar fitting back onto the socket with the shade sandwiched between the collar fitting and socket.
We recommend using 1 Type A19 light bulb. 120V 60Hz AC only.
Next, screw in your light bulb. We recommend using one Type A19 light bulb. 120V 60Hz AC only.
2
Bulb (not included)
16
Step 16 Finally, set the Fixture Assembly (1) to the desired orientation by adjusting each component with the Allen Key (M) at the set swivel points.
M
Adjust tightness as needed
90˚
1. Loosen the decorative thumb screws
your desired angle
17
3. Re-tighten the decorative thumb screws
Hardwired option assembly Step 1 Let’s get this thing fired up! Or should we say, lit? Separate the Fixture Assembly (1) from the Mounting Unit (G) by removing the Fixture Screws (B).
1
G B
B
B B
B
B
B
B
18
Step 2 Carefully raise the flap on the wire connector to release the clear wire. Repeat this step on the second connect so that both clear wires have been removed and the black and white wires remain attached to the Fixture Assembly (1). Once the wires have been disconnected, prepare yourself for the grand unraveling! Untie the knot that has kept the two clear wires intertwined.
1ST 2 ND
1
L
Clear with “L”(Hot)
Black 1
1ST 2ND
2
3
Clear(Neutral)
7
White
Step 3 Voila! With the knot untied, carefully pull the cord through the bottom hole of the Fixture Assembly (1), giving it a gentle tug to guide it.
1
19
Step 4 Insert the Plastic Cap (I) into the bottom of the Fixture to cap off the hole. Twist on the Decorative the bottom of the Fixture.
I
Step 5 Mount the Mounting Plate (A) to the electrical box using the Junction Box Screws M4*25mm (C).
A C
Note: Be sure that you are only making the connections to a 120V 60Hz AC circuit. If you do not have a pre-existing electrical box, we strongly advise using a certified electrician.
20
Step 6 First, wrap the ground wire from the Fixture Assembly (1) around the grounding screw on the Mounting Plate (A) and then secure it in place by tightening the grounding screw. Next, use the Wire Connectors (D) to join the ground wires from the Fixture Assembly (1) and from the electrical box.
D
D
A
21
Step 7 Feed the designated wires into their respective wire connectors, as shown below.
2 ND 1 ST
White (Neutral)
Black (Hot)
2
ND
1
22
ST
Step 8 Attach Fixture Assembly (1) to the Mounting Plate (A). Align the holes on the Fixture with the exposed screws. Tighten them securely using the Fixture Screws (B). Turn the Fixture Screws (B) in a counter-clockwise direction. Unscrew the collar fitting from the Fixture Assembly (1) by turning it clockwise until it comes off.
1
A
B
B
B
B
23
Step 9 Install the Lamp Shade (2) by setting it in place with the shade collar fitting. Thread the collar fitting back onto the socket with the shade sandwiched between the collar fitting and socket. Next, screw in your light bulb. We recommend using one Type A19 light bulb. 120V 60Hz AC only.
2
We recommend using 1 Type A19 light bulb. 120V 60Hz AC only.
Bulb (not included)
24
Step 10 Finally, set the Fixture Assembly (1) to the desired orientation by adjusting each component with the Allen Key (M) at the set swivel points.
M
Adjust tightness as needed
90°
1. Loosen the decorative thumb screws
your desired angle
25
3. Re-tighten the decorative thumb screws
Questions? Don’t worry, we’ve got the answers What other light bulbs can fit in this light?
Is this light compatible outside North America?
The bulb must not be greater than the max wattage for the fixture. It must match the base size, and the diameter of any area of the bulb should be less than diameter of any area of shade, so that it can fit.
Our lighting is only warranted in Canada and the United States.
What do I do if the product is not working?
Can I use an LED light bulb?
Try a different light bulb and confirm proper installation.
Yes, so long that the base size matches and the diameter of any area of bulb is less than diameter of any area of shade, so that it can fit.
Can these lights work on a dimmer? Dimmability is related to the light bulb and the wall switch, not the light fixture. All our hardwire fixtures are compatible with dimmable light bulbs. We recommend using a dimmer switch, as it extends the life of the bulb and allows for energy saving and great ambiance. If using a LED bulb, please ensure both your LED bulb and dimmer switch are compatible.
Is this UL/ETL certified? Yes, all our products are either UL or ETL.
Do I need an electrician to set up the hardwire? We recommend using a certified electrician for all hardwiring, although all of our fixtures can be set up without an electrician, as long as you are replacing an existing fixture or have an existing junction box ready for a fixture installation. ENSURE POWER IS OFF WHEN INSTALLING. For all new constructions, please use a certified electrician.
Can I use the fixture outdoors? No, this product was not designed to be used outdoors.
Can I retrofit this hard-wired to a plug-in or vice-versa? Yes, a plug-in fixture can be turned into a hardwire fixture and a hardwire fixture can become a plug-in fixture. For many products we will provide all the necessary hardware to make these changes, if not, you will need to purchase the necessary hardware.
26
No heartburn, when we handle the return Give us a call 1-866-619-1004 or shoot us a message at help@nathanjames.com we will issue you a free replacement with zero hassle.
Our way
Their way
Give us a call
Re-package item
Replacement
Schedule pick up
You
Track package Replacement You
We really don’t want you to go through the hassle of re-packaging your item and sending it back, because let’s be honest…nobody has time for that.
27
We are only in business if you’re happy For starters, thanks for being you. Toll-free at 1-866-619-1004 Help@nathanjames.com NathanJames.com/help
We do our best to ensure your product arrives without any problems, but occasionally mistakes happen—as humans we are imperfect beings. In the event that a part is damaged or missing, we will be more than happy to provide you with replacement part(s) for free.
Warranty This product comes with a lifetime warranty from the date of purchase. Please use your phone to scan the QR code to register your product or visit https://goo.gl/i9dk3q
Did we do alright? Please spread the love! If you are happy with your product, tell your friends and family about us or even better leave us a review online. Spreading the word gives us the opportunity to make more people happy and keep our prices low for your next purchase.
Brooke Burdon Founder, Nathan James
28