1/4
73 509
eduard
Su-27SM Flanker B S.A.
73 509
1/72 scale detail set for Zvezda 7295 kit • sada detailů pro model 1/72 Zvezda 7295
APPLY EXPRESS MASK AND PAINT BEFORE GLUING POUŽÍT EXPRESS MASK NABARVIT PRED SLEPENÍM SYMETRICAL ASSEMBLY SYMETRICKÁ MONTÁŽ REMOVE ODSTRANIT
BEND OHNOUT
GRIND OBROUSIT
?
REPLACE NAHRADIT
DRILL HOLE VRTAT OTVOR
ORIGINAL KIT PARTS PŮVODNÍ DÍLY STAVEBNICE
OPTION VOLBA
1
COLORED ETCHED PARTS LEPTANÉ BAREVNÉ DÍLY
1
ETCHED PARTS LEPTANÉ NEBAREVNÉ DÍLY
1
ORIGINAL KIT PARTS PŮVODNÍ DÍLY STAVEBNICE
PARTS TO BE REMOVED DÍLY K ODSTRANĚNÍ
PHOTO-ETCHED PARTS LEPTANÉ DÍLY
FILL TMELIT
B3
37
39
40
34
D2 11 7
A19
18
1
2
B56
14
15 B22
67
D11, D12 A19
9 8
10 55 12
B39 + B13, B41 + B12 5
3 B45
13
8
6
2/4
73 509
36
51
D7
19
D8
57
plastic = 0,8mm l = 2mm
60 27
E6
58 30 38 56
Film
D3 21
D3
22
25 35
C10
Fuselage 4 28 29 33 53
66
57 20
D10
58 16 46
B61 32
26
66
A1, B33
D9 54
Fuselage 24
23
Fill E2
61
3 pcs. 66 41
B25
61
2 pcs. 17
D17
B24
3/4
73 509
B32 B30, B31
64
B17 31
B18 70
49
65 47 72
B7
B8
75 47 79
B34, B60, B11, B26
31
52
B32 D1 44
33
20
A1
Fuselage
73
74
63 48
45
68
63
69
A1 77
78 71 Fuselage
A1
4/4
73 509
76
42
59
C6
C14, B42, B43
C18 ? C13 2 pcs. 62
43
C5
50
C7, C8 2 pcs. 62
C16 ? C15
PARTS WITH GLUE
DÍLY OPATŘENÉ LEPIDLEM 3. Do not touch the adhesive areas of the etched components.
3. Nesahejte na části dílů, na kterých je naneseno lepidlo.
1. Separate the etched components from their frames on the protective paper. Removal from the paper is done only after separation of the parts from the frames.
1.Samolepící díly oddělujte od rámečku na podkladovém papíře. Po oddělení je sejměte z krycího papíru.
4. Hold the parts by the edges, or at areas free of adhesive. 4. Samolepící díly berte za hrany nebo za části, na kterých není nanesené lepidlo.
5. Lightly place the component in the desired location and position. Adjust as required. The component will be permanently affixed when pressed onto its intended location, its location can be adjusted.
2. Do not inadvertently place etched componets on an unwanted surface. Attempts to remove will result in damage to your part. 2. Nepokládejte samolepící díly na volné plochy. Pokud je omylem přilepíte, při pokusu o odlepení dojde k poškození dílu.
© EDUARD M.A. 2014
5. Díl lehce položte do pozice, ve které má být nalepen. Upravte přesnou pozici a přimáčkněte. Díl dokonale přilne až po přimáčknutí, před přimáčknutím lze dílem opatrně manipulovat.
www.eduard.com
Made in Czech Republic