49 427
1/4
eduard
LaGG-3 S.A.
49 427
1/48 scale detail set for ICM kit • sada detailů pro model 1/48 ICM
APPLY EXPRESS MASK AND PAINT BEFORE GLUING POUŽÍT EXPRESS MASK NABARVIT PRED SLEPENÍM SYMETRICAL ASSEMBLY SYMETRICKÁ MONTÁŽ REMOVE ODSTRANIT
BEND OHNOUT
?
GRIND OBROUSIT
OPTION VOLBA REPLACE NAHRADIT
DRILL HOLE VRTAT OTVOR
FILM
ORIGINAL KIT PARTS PŮVODNÍ DÍLY STAVEBNICE
PARTS TO BE REMOVED DÍLY K ODSTRANĚNÍ
PHOTO-ETCHED PARTS LEPTANÉ DÍLY
16
B16
17
A
B
FILL TMELIT
15 17
17
15A
18
17 23 13
B9
11
11
B8
2 3 20
A16
A
22 22
56 B2
A1
B A9
B16
1 =
D3
9
10
8 24
A13
25 7
49 427
2/4
14 4 A1
B2
12
6 40 14
14 33
5
14
B45
19 21
36
29
B15
62
B3
A11
?
35
B6
A12
14
59 B4
ball pen
61
plastic - 0,6mm l - 0,5mm
58, 57
64
50 58
49 51 55 B21
B20
44
A1, B2
plastic - 0,1mm l - 0,8mm
45
44
53 32
ball pen B37
31, 30
28
26
B44
B43
B14, B13
31
30
46
57
49 427
3/4
film
B11
6 pcs.
A3 A21
A2
41
C1
D6
63
65
A1, B2
38 B18
54
43
60 60
48
A1, B2, A9
A1, B2
34 5 pcs.
34 5 pcs.
62
A14
2 pcs. 39
52
B19
60 A1, B2
37 27
47
42
60 2 pcs.
C1 C2
C3
60 5 pcs.
For futher detail sets look for eduard 48 608 LaGG-3 Landing Flaps (not included in this set) © EDUARD M.A. 2008
www.eduard.com
Made in Czech Republic
5/5
49 427
49 427
LaGG-3 S.A. 1/48 scale detail set for ICM kit • sada detailů pro model 1/48 ICM
3. Do not touch the adhesive areas of the etched components. 1. Separate the etched components from their frames on the 3. Nesahejte na části dílů, na kterých je naneseno lepidlo. protective paper. Removal from the paper is done only after separation of the parts from the frames.
1.Samolepící díly oddělujte od rámečku na podkladovém papíře. Po oddělení je sejměte z krycího papíru.
4. Hold the parts by the edges, or at areas free of adhesive.
4. Samolepící díly berte za hrany nebo za části, na kterých není nanesené lepidlo.
5. Lightly place the component in the desired location and position. Adjust as required. The component will by permanently affixed when pressed onto its intended location, its location can be adjusted.
2. Do not inadvertently place etched componets on an 5. Díl lehce položte do pozice, ve které má být nalepen. unwanted surface. Attempts to remove will result in Upravte přesnou pozici a přimáčkněte. Díl dokonale přilne damage to your part. až po přimáčknutí, před přimáčknutím lze dílem opatrně 2. Nepokládejte samolepící díly na volné plochy. Pokud je omylem přilepíte, při pokusu o odlepení dojde k poškození dílu.
manipulovat.