House ARCH 5101 6 Sasa A Ass The Seamless House Lawson St ARCH 5101 - PB! deadline description 2022.05.02 10% schematic design (SD) Dina Lin (15.5', 57.5', -3') Ø<2.5ft, 13.5°> Sasa Zivkovic Assistant Professor Lawson Spencer 5 Studio Consultant deadline description 2022.05.02 10% schematic design (SD) (9.7', 50.3', -3') Ø<2.5ft, 15°> (30.8', 50.5', -6') (19', 50', -3') Ø<4.5ft> Ø<2.5ft, 14°> drawing notes ## write all drawing notes here drawing notes ## write all drawing notes here (12.7', 37.5', -7') Ø<6.2ft, (34.6', 34.4', -5') 4.4ft> Ø<2.5ft> ft, 5 .5 ft> 4 additional notes:-- Ø< Ø<4.8ft, 3.7ft> ft, 5 .6 ft> (19.2', 20.6', -8') Ø<5.6ft, 3ft> 5.7 3 Ø< (35.7', 17.5', -5') (11', 6', -3') date last revised: February 14, 2023 4:36 PM A 6.4 (34.3', 24.7', -5') (11.8', 22.9', -8') Ø<2.5ft, 15°> (22.6', 8.5', -3') tN Project Address 42°26'58.83"N, 76°29'4.92"W Ø<2.5ft, 13.5°> (15.3', 4.4', -3') (project location) Ø<3ft, 13.5°> Elevations 2 A1.03 F E D C B A The S H ARC 6 Foundation Plan Roof Plan tN Project Address 2023-02-15 3:00 AM 1 42°26'58.83"N, 76°29'4.92"W (project location) Roof Plan and Foundation Plan (15 .5', date: (9.7', F E 50.3', 57.5', (15 .5', -3') (9.7', -3') (19 ', 50 D .7', .8', 37.5', -7') 50.5', 57.5', A1.04 -3') -3') C ', -3') (30 (12 50.3', (19 B ', 50 (30 (12 -6') ', -3') .7', .8', 37.5', 50.5', -7') deadline descript 2022.05.02 10% sch A -6') 5 (11 .8', 22.9', (34 .6', -8') (19 (11 ', 6', .2', -3') 20.6', -8') .3', .3', .7', 4.4', -3') (22 .6', 8.5', (11 .8', -5') 17.5', 24.7', 22.9', (34 .6', -8') (19 (11 (34 (35 (15 34.4', ', 6', .2', -3') 20.6', -8') (34 .3', -5') (35 (15 -5') .3', -3') .7', 4.4', -3') (22 .6', 8.5', 17.5', 24.7', 34.4', -5') -5') -5') drawing notes -3') ## date last revised: February 14, 2023 4:36 PM additional notes:-- 4 Step One: Step Two: Step Three: Step Four: - Set up the printer - Put dirt on the site (All Covered) - Use the 3d printer to excavate the dirt on the exact locations of fooings - Put the foundation piers set in the designated locations as shown above - (X, Y, Z) from the site origin point - Print the foundations - Cast the floors between the 3d printed walls - Keep Printing - Print the walls - Put insulation between the double layer walls - Put steel reinforcement along the printing process Step Five: Step Six: Step Seven: Step Eight: - Print the walls and openings - Cast the Floors - Keep prining until the house if finished - Wait until the concrete is cured - Add roof structures and base layer of insulation - Add window frames and glazings - Add roof insulation and metal covering write all drawing n 3 2 -15 3:00 AM tN 1 Project Address 42°26'58.83"N, 76°29'4.9 Construction Se