Skip to main content

MMP_3999 31julio2026

Page 1


DOOR INSTALLATION

AJUSTE DE PROFUNDIDAD / DEPTH ADJUSTMENT

AJUSTE LATERAL / LATERAL ADJUSTMENT

AJUSTE DEALTURA / HEIGHT ADJUSTMENT B I J L H G H A A K

Alto/ 104,1cm / Height: 40,98 in

Ancho/ 32 cm / Width: 12,59 in Fondo/ 25 cm / Depth: 9,84 in

Al finalizar el ajuste, cubra las cajas con las tapas adhesivas/ After tightening all the panels, cover the minifix camswiththeadhesivecaps.

LOTE No:

Al terminar de armar, desprenda los adhesivos (en caso de que queden residuos de pegamento, limpie la superficie con alcohol) / After finishing the assembly, take off the adhesives. (In case of glue residues,wipethemwithalcohol)

(572) 691 17 00

(572) 695 91 81

RECOMENDACIONES IMPORTANTES KEY RECOMMENDATIONS

NO pinte el mueble / Do not paint the furniture.

NO lavar las manijas o tiraderas con jabones o elementos abrasivos / Do not wash handles or dumps with soap or abrasives.

NO mojar o ubicar a la intemperie / Do not expose to rain or direct sun.

NO sobrecargue el mueble. no exceda el peso de 30 kilos para gabinetes de cocina / Do not overload the cabinet. Weight max. 66lbs for kitchen cabinets. O O O O O

NO golpear ni martillar el mueble (hágalo sólo donde se indique) / Do not hit or hammer the furniture (just do it where is indicated).

NO permita que los niños manipulen el mueble, puede voltearse y lastimarlos / Do not allow children to handle the cabinets or drawers, they could get hurt.

SIEMPRE levante el mueble entre dos personas, NO lo arrastre / Do not drag thefurniture Lift it between two people.

Limpie con paño seco , / Clean with a dry cloth.

HERRAJES BÁSICOS PARA MUEBLES RTA BASIC HARDWARE FOR RTA FURNITURE

1.Abrir la caja del mueble y buscar la bolsa con los herrajes / Open the box and look for the hardware bag.

P2.Abrir el paquete y comprobar que el contenido de las piezas es correcto / Open the package and verify that the content of the pieces is correct.

3. Separe los herrajes para facilitar su identificación durante el armado / Separate hardware for easy identification during assembly.

4.Arme el mueble en un lugar limpio y en una superficie plana / RTAfurniture must be assembled in a clean place and on a flat surface.

INSTALACIÓN A LA PARED

* Herramientas NO incluidas/ Tools not included

Utilizar una broca de 5/16" para hacer las perforaciones en el muro/ Use a 5/16" drill bit to drill the wall.

El buen funcionamiento del mueble depende de un adecuado ensamblaje An excellent furniture´s performance relies on a solid and a suitable assembly. RECOMENDACIONES DE ENSAMBLE / ASSEMBLYRECOMENDATIONS

MINIFIX / CONNECTOR - DOWELS

180°

Tornillo 2" + Chazo Mariposa/ Drywall Screw+ Wall Anchor

DEFINA EL LADO DE APERTURA DE LAS PUERTAS GIRANDO EL MUEBLE 180° / IDEFINE THE OPENING SIDE OF THE DOORS TURNING THE 180 ° FURNITURE VOLTEAR/ TURN OVER

Sistemadeunióncompuestoporunperno(A)yunacajaminifix(B).

(1)Seinsertalacajaminifixdentrodelaperforaciónubicadaenlacaradelapieza,laflechadebeapuntarsiemprea ladireccióndelaperforaciónpordondeentraráelperno.

(2)Sedebeinsertarelpernoporsuparteplásticaenlasperforacionesqueseindiquen,luegoseinsertalapunta metálicaenlaperforaciónparaquesucabezaquedealinteriordelacajaminifix.

(3)Girarlacajaminifix180°paraapretarlasdospiezas.

It´safittingsystemmadeofaspreadingbolt(A)andaminifixcam(B).

(1)Inserttheminifixcamintheholeplacedinthefaceofthepanelwiththearrowpontingtowardstheholewheretheboltwill fit.

(2)Inserttheboltwithitsplasticbaseintheshownholes,theninsertthemetallicboltheadintheholessoitfitsinsidethe minifixcam.

(3)Tightthepanelsbyturningtheminifixcam180°.

TARUGOS O TAQUETES / FLUTED DOWELPIN

caja minifix / dowels hole

Esunpedazodemaderacortoygrueso,deaproximadamente3a10cmdelargo,quesirveparaamarrarelmuebley darleresistencia.

It´s ashortandthickpieceofwood,1,18to3,9inchesaproximately,whichisusedtotiethecabinetandgiveitresistence.

Anchor

VOLTEAR TURN OVER

Se recomienda armar el mueble sobre la caja o una superficie lisa para no rayarlo. It is recommended to assemble the product on the box or on a flat surface to not scratch it.

Voltear el mueble cuidadosamente para ensamblar los fondos. Carefully turn over the cabinet to assemble the back panels.

PESO MAX. SUGERIDO EN MUEBLE (Kg) / MAX SUGGESTED LOAD (Kg)

NOTA: La resistencia a las cargas puede variar dependiendo si es una carga distribuida o una carga puntual, las grácas corresponden a cargas puntuales, NO exceder los pesos sugeridos / NOTE: The load capacity depends if it is a point load or if it is an uniform distributed load, do not exceed the suggested loads. 1 1/8"

Tarugo/ Fluted Dowel Pin

HERRAJES PARAARMADO ASSEMBLY

HARDWARE

Tornillo de Ensamble 1 1/8"/ 1 1/8" Drywall Screw x2 Manija/ Handle L L K K G H H A

Adhesiva Minifix COLOR 2/ Cover Caps

Chazo Plástico + Tornillo de Ensamble/ Plastic Wall Anchor + Drywall Screw x2

Perno minifix/ Spreading Bolt

Minifix/ Minifix Cams

Lámina/ Sheet Screw

x4

INSERTE EL MODULO DENTRO DEL MUEBLE / INSERT THE MODULE INSIDE THE CABINET

TENER PRECAUCIÓN AL ABRIR LA BOLSA DE HERRAJES PARA NO EXTRAVIAR NINGUNO. COMPRUEBE QUE EL CONTENIDO DE LAS PIEZAS SEA EL CORRECTO. EN CASO QUE FALTE ALGUNA PIEZA O ESTE DEFECTUOSA DEVUELVA LAS PIEZAS AL ALMACÉN CON SU FACTURA PARA EFECTUAR EL CAMBIO DE LAS PIEZAS Y/O LOS HERRAJES LO MÁS PRONTO POSIBLE./ PLEASE BE CAUTIOUS WHEN OPENING THE HARDWARE BAG TO NOT LOSE ANY CHECK THE CONTENTS OF THE PARTS ARE CORRECT. IF ANY PART IS MISSING OR IMPERFECT PLEASE RETURN THE PARTS TO THE STORE WITH THE PRODUCT INVOICE ATTACHED TO MAKE EFECTIVE THE REPLACEMENT OF THE IMPERFECTPIECESORHARDWAREASSOONASPOSSIBLE.

x28
Tornillo
x24
Tapa Adhesiva Minifix COLOR 1/ Cover Caps
x4
Tapa
x4
Bisagra Interior/ Half Overlay Hinge

PIEZAS DEARMADO ASSEMBLY PARTS

X 2 G X 2 H X 2 I J K X 2 LX 2 M X 2

ANTES DE EMPEZAR A ARMAR EL MUEBLE LEA DETENIDAMENTE LAS INSTRUCCIONES. SE RECOMIENDA ARMAR EL MUEBLE SOBRE LA CAJA O SOBRE UNA SUPERFICIE LISA Y CUBIERTA, PARA NO RAYARLO / BEFORE STARTING TO ASSEMBLE THE CABINET, CAREFULLY READ THE INSTRUCTIONS. IT IS RECOMMENDED TO ASSEMBLE THE FURNITURE ON THE BOX OR ON A FLAT AND COVERED SURFACE IN ORDER TO NOT SCRATCH THE PRODUCT

Girar 180° / Rotate 180°
Girar 180° / Rotate 180°

AX 2

D X 2

AX 2

B A H G G H A M M

Girar 180° / Rotate 180°

VOLTEAR/ TURN OVER

DESLICE LOS FONDOS DENTRO DEL MUEBLE / SLIDE THE FUNDS INSIDE THE CABINET

Girar 180° / Rotate 180°

G X 2

G X 2

VOLTEAR/ TURN OVER

Girar 180° / Rotate 180°
Girar 180° / Rotate 180°

Turn static files into dynamic content formats.

Create a flipbook