CLC_5363

The plastic stop should be placed on the rear

Revisar que el tope plástico del riel quede en la PARTETRASERA/

Rotate Voltear

The plastic stop should be placed on the rear. Revisar que el tope plástico del riel quede en la PARTETRASERA/

Rotate Voltear

Rotate to tighten.

Gire para apretar

Rotate to tighten.

Gire para apretar

Rotate to tighten.

Gire para apretar.

G H I I K J J

Rotate to tighten.

Gire para apretar.

Rotate to tighten.

Gire para apretar.

Rotate to tighten.

Gire para apretar

When placing the slide on the side of the drawer, the metallic stop should be placed on the front.

Para poner el riel en el lateral del cajón revisar que el tope metálico quede en la PARTE DELANTERA

Rotate to tighten.

Gire para apretar.

BEFORE YOU CONTINUE THE ASSEMBLY, MEASURE THE SPACE WHERE YOU ARE GOING TO PUT THE CLOSET AND CUT PIECES A AND B, AND OVAL TUBES IF NECESSARY, FOR THIS TAKE AS A GUIDE THE FIGURE BELOW ANTES DE CONTINUAR CON EL ENSAMBLE, MIDA EL ESPACIO DONDE VA A PONER EL CLÓSET Y CORTE

LAS PIEZAS A Y B, Y LOS TUBOS OVALADOS SI ES NECESARIO, PARA ESTO TOME COMO GUIA LA FIGURA DE ABAJO/

* Tools not included/ Herramientas no incluidas

* Inches / Centímetros

Use a pencil to mark the cutting of pieces A and B, then use the appropriate tools for cutting / Utilizar lapiz para marcar el corte de las piezas A y B, luego utilizar herramientas apropiadas para realizar el corte

* Total Measures/ Medidas Totales

/ Pared

SIDE WALL/ Pared lateral

,71 184,7 1,25 3,2

DRILL HOLES ON THE WALL TO ANCHOR THE ROD SUPPORTS AND THE WIDE BRACES / TALADRE LOS AGUJEROS EN LA PARED PARA ANCLAR EL SOPORTE DEL TUBO Y LAS CANTONERAS

Mark with a pencil the holes of the Wide Bracers on the wall (Wall Anchor not included/ Marque con un lapiz los agujeros de las cantoneras en la pared (Chazos no incluidos)

* Inches / Centímetros

Drywall Screw+ Wall Anchor/ Tornillo 2 1/2" + Chazo Mariposa

WALL / Pared

* Tools not included/ Herramientas NO incluidas

After you finish the adjustment of the cams, cover them with the cover caps.

Después de ajustar todas las cajas minifix, cúbralas con las tapas adhesivas.

AUse a 5/16" drill bit to drill the wall/ Utilizar una broca de 5/16" para hacer las perforaciones en el muro

After you finish assembling the cabinet, take off the adhesive letters.

Al terminar de armar, desprenda las letras adhesivas.

Wall Anchoring / Anclaje a la pared

A/B 1

A/B 2

Slide the drawer into the cabinet / Deslice el cajón dentro del mueble

WARRANTY POLICY

Furniture has a 1 year warranty coverage in wooden parts and hardware pieces since its manufacturing date, which you can see in the lot number printed on the product box and the assembly instructions leaflet.

Warranty covers materials and workmanship imperfections which impair the assembly or correct functioning of the cabinet.

This warranty is not valid if the defects or imperfections are caused by the incorrect following of the assembly instructions, warnings and recommendations, misuse, intentional damage, fire or flood, or after modifications or any kind of alteration, or repaired by someone not authorized, when it´s been assembled 3 months after the date of purchase These defects MUST be reported before the warranty coverage period ends. Once the product has been assembled, the company will not be responsible for defective and/or damaged parts.

This warranty is ONLY valid for the ORIGINAL PURCHASER, it doesn’t apply if the product has been resold, rented, etc.

Furniture will take no liability for incidental or consequential damages caused to or by the product (This may not apply in your state).

To make this warranty valid you must write to our customer service email describing the product defect, lot number and submitting your sales reciept or proof of purchase, or contact us at our customer service line. Replaced parts will be under the product´s original warranty coverage period. Damaged parts will become property of the company

There are no other warranties applicable to this product.