Deslice los cajones dentro del mueble/ Slide the drawers inside the cabinet
Al finalizar el ajuste, cubra las cajas con las tapas adhesivas/ After tightening all the panels, cover the minifix camswiththeadhesivecaps.
Alto/ 180 cm / Height: 70,86 in
Ancho/ 40 cm / Width: 15,75 in
Fondo/ 40 cm / Depth: 15,75 in
LOTE No:
Al terminar de armar, desprenda los adhesivos (en caso de que queden residuos de pegamento, limpie la superficie con alcohol) / After finishing the assembly, take off the adhesives. (In case of glue residues,wipethemwithalcohol)
By: TEL (572) 691 17 00 PBX (572) 695 91 81 CALI - COLOMBIA www.rta.com.co
RECOMENDACIONES IMPORTANTES KEY RECOMMENDATIONS
NO pinte el mueble / Do not paint the furniture.
NO lavar las manijas o tiraderas con jabones o elementos abrasivos / Do not wash handles or dumps with soap or abrasives.
NO mojar o ubicar a la intemperie / Do not expose to rain or direct sun.
NO sobrecargue el mueble. no exceda el peso de 30 kilos para gabinetes de cocina / Do not overload the cabinet. Weight max. 66lbs for kitchen cabinets. O O O O O O
NO golpear ni martillar el mueble (hágalo sólo donde se indique) / Do not hit or hammer the furniture (just do it where is indicated).
NO permita que los niños manipulen el mueble, puede voltearse y lastimarlos / Do not allow children to handle the cabinets or drawers, they could get hurt.
Limpie con paño seco , / Clean with a dry cloth. P P
SIEMPRE levante el mueble entre dos personas, NO lo arrastre / Do not drag thefurniture Lift it between two people.
HERRAJES BÁSICOS PARA MUEBLES RTA
BASIC HARDWARE FOR RTA FURNITURE
1.Abrir la caja del mueble y buscar la bolsa con los herrajes / Open the box and look for the hardware bag.
2.Abrir el paquete y comprobar que el contenido de las piezas es correcto / Open the package and verify that the content of the pieces is correct.
3. Separe los herrajes para facilitar su identificación durante el armado / Separate hardware for easy identification during assembly.
VOLTEAR TURN OVER H O S
4.Arme el mueble en un lugar limpio y en una superficie plana / RTAfurniture must be assembled in a clean place and on a flat surface. O S J H I
S 1 2
Girar 180° / Rotate 180°
El buen funcionamiento del mueble depende de un adecuado ensamblaje An excellent furniture´s performance relies on a solid and a suitable assembly. RECOMENDACIONES DE ENSAMBLE / ASSEMBLYRECOMENDATIONS
MINIFIX / CONNECTOR - DOWELS
1 2 3 A B
Sistemadeunióncompuestoporunperno(A)yunacajaminifix(B).
(1)Seinsertalacajaminifixdentrodelaperforaciónubicadaenlacaradelapieza,laflechadebeapuntarsiemprea ladireccióndelaperforaciónpordondeentraráelperno.
(2)Sedebeinsertarelpernoporsuparteplásticaenlasperforacionesqueseindiquen,luegoseinsertalapunta metálicaenlaperforaciónparaquesucabezaquedealinteriordelacajaminifix.
(3)Girarlacajaminifix180°paraapretarlasdospiezas.
It´safittingsystemmadeofaspreadingbolt(A)andaminifixcam(B).
(1)Inserttheminifixcamintheholeplacedinthefaceofthepanelwiththearrowpontingtowardstheholewheretheboltwill fit.
(2)Inserttheboltwithitsplasticbaseintheshownholes,theninsertthemetallicboltheadintheholessoitfitsinsidethe minifixcam.
(3)Tightthepanelsbyturningtheminifixcam180°.
TARUGOS O TAQUETES / FLUTED DOWELPIN
caja minifix / dowels hole
Esunpedazodemaderacortoygrueso,deaproximadamente3a10cmdelargo,quesirveparaamarrarelmuebley darleresistencia.
It´s ashortandthickpieceofwood,1,18to3,9inchesaproximately,whichisusedtotiethecabinetandgiveitresistence. 180°
RECOMENDACIONES IMPORTANTES / KEY RECOMMENDATIONS
PESO MAX. SUGERIDO EN MUEBLE (Kg) / MAX SUGGESTED LOAD (Kg)
Se recomienda armar el mueble sobre la caja o una superficie lisa para no rayarlo. It is recommended to assemble the product on the box or on a flat surface to not scratch it.
VOLTEAR TURN OVER
Voltear el mueble cuidadosamente para ensamblar los fondos. Carefully turn over the cabinet to assemble the back panels.
NOTA: La resistencia a las cargas puede variar dependiendo si es una carga distribuida o una carga puntual, las gráficas corresponden a cargas puntuales, NO exceder los pesos sugeridos / NOTE: The load capacity depends if it is a point load or if it is a uniform distributed load, do not exceed the suggested loads.
DOOR INSTALLATION
AJUSTE DE ALTURA / HEIGHT ADJUSTMENT
AJUSTE DE PROFUNDIDAD / DEPTH ADJUSTMENT
AJUSTE LATERAL / LATERAL ADJUSTMENT
HERRAJES PARAARMADO ASSEMBLY HARDWARE
Perno minifix/ Spreading Bolt x52
Tarugo/ Fluted Dowel Pin x22
Tornillo Lámina/ Sheet Screw
Minifix/ Minifix Cams x27
x30
Tapa Adhesiva Minifix/ Cover Caps
Riel Sencillo/ (Incluye tornillos) Drawer Slides (Incluides screws) x2
Tornillo 2 1/2" + Chazo Mariposa/ Drywall Screw+ Wall Anchor
Bisagra Parche/ (Incluye tornillos) Full Overlay Hinge (Incluides screws)
Soporte Entrepaño/ Shelf Support
TENER PRECAUCIÓN AL ABRIR LA BOLSA DE HERRAJES PARA NO EXTRAVIAR NINGUNO. COMPRUEBE QUE EL CONTENIDO DE LAS PIEZAS SEA EL CORRECTO. EN CASO QUE FALTE ALGUNA PIEZA O ESTE DEFECTUOSA DEVUELVA LAS PIEZAS AL ALMACÉN CON SU FACTURA PARA EFECTUAR EL CAMBIO DE LAS PIEZAS Y/O LOS HERRAJES LO MÁS PRONTO POSIBLE./ PLEASE BE CAUTIOUS WHEN OPENING THE HARDWARE BAG TO NOT LOSE ANY CHECK THE CONTENTS OF THE PARTS ARE CORRECT. IF ANY PART IS MISSING OR IMPERFECT PLEASE RETURN THE PARTS TO THE STORE WITH THE PRODUCT INVOICE ATTACHED TO MAKE EFECTIVE THE REPLACEMENT OF THE IMPERFECTPIECESORHARDWAREASSOONASPOSSIBLE.
ANTES DE EMPEZAR A ARMAR EL MUEBLE LEA DETENIDAMENTE LAS INSTRUCCIONES. SE RECOMIENDA ARMAR EL MUEBLE SOBRE LA CAJA O SOBRE UNA SUPERFICIE LISA Y CUBIERTA, PARA NO RAYARLO / BEFORE STARTING TO ASSEMBLE THE CABINET, CAREFULLY READ THE INSTRUCTIONS. IT IS RECOMMENDED TO ASSEMBLE THE FURNITURE ON THE BOX OR ON A FLAT AND COVERED SURFACE IN ORDER TO NOT SCRATCH THE PRODUCT
Utilizar una broca de 5/16" para hacer las perforaciones en el muro/ Use a 5/16" drill bit to drill the wall.
* Herramientas NO incluidas/ Tools not included
Tornillo 2" + Chazo Mariposa/ Drywall Screw + Wall Anchor
*Colocar el entrepaño móvil sobre los soportes
* Centímetros / Inches
Girar 180° / Rotate 180°
Girar 180° / Rotate 180°
Girar 180° / Rotate 180°
Girar 180° / Rotate 180°
VOLTEAR TURN OVER
4° Perforación
VOLTEAR TURN OVER