OL L A PEN DANT 3 4 " Ø
2 1 2 . 6 2 5 .9 6 0 5
INSTAL L INST R UC T ION S
ST U D I O @ L AV IVAHOM E.C OM
FI X ED LENGTH
PAGE 1 OF 2
DATE 10.13.22
PLEASE NOTE All of our lighting is carefully inspected and electrically tested prior to shipping. Once received, we ask that you please inspect thoroughly—prior to installation—for any physical defects which may have occurred during shipping. Lighting that has been installed is not eligible for return or exchange, and L’Aviva Home does not take any responsibility for any damage incurred during installation itself.
Please be sure, too, to note the maximum recommended wattage for your fixture when choosing a bulb; using higher wattage bulbs can short the wiring, and L’Aviva Home does not take responsibility for any damage incurred under these circumstances.
CAREFULLY REMOVE FIXTURE FROM PACKING MATERIALS
CONTENTS
INSTALLATION
•
Copper Shade and Fixture Assembly
1.This product must be installed in accordance with the applicable
•
Mounting Cross Bar
installation code by a person familiar with the construction and
•
8-32 Cross Bar Screws (2x)
•
Wire Nuts (2x)
•
Canopy
•
Screw Caps (2x)
•
Stem Assembly
•
Coupling with Set Screws
4. Thread stem assembly into coupling on ffixture body and secure
•
E26 Bulbs, A19 LED (3x)
with set screw (in coupling)
operation of the product and the hazards involved. 2. Turn off power to junction box before installing. 3. Feed wires from fixture body up through stem assembly with stem coupling end up.
5. Slip canopy over stem assembly and rest on top of coupling on fixture body.
OLL A PENDAN T 3 4 " Ø
2 1 2 . 6 2 5 .9 6 0 5
INSTA L L IN ST R UCT IONS
ST U D I O @ L AV IVAHOM E.C OM
PAGE 2 OF 2 | OLLA INSTALL INSTRUCTIONS
DATE 10.13.22
FI X ED LENGTH
6. Thread (2 provided) 8-32 Screws in to bracket bar and lock with (2 provided) 8-32 screw caps
THISbar PRODUCT MUST BE pointed INSTALLED IN 7. Thread1. bracket (with screws installed down towards
NUT
fixture body) onto stem assembly and secure with (1 provided) lock
LOCK WASHER
ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH washer and nut. THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
BRACKET BAR
8. Raise fixture and secure bracket bar to junction box with (2
8-32 SCREWS
2. FEED WIRES FROM FIXTURE BODY UP THROUGH provided) 8-32 screws. STEM ASSEMBLY WITH STEM COUPLING END UP.
STEM COUPLING LOCK BALL
THREAD ASSEMBLY INTO COUPLING 9. Attach 3. ground wire to STEM green ground screw on bracket bar.
ON FIXTURE BODY AND SECURE WITH SET SCREW (in coupling).
STEM ASSEMBLY CANOPY
10. Perform wire makeup using (2 provided) wire nuts - ensuring
CANOPY OVER STEM ASSEMBLY AND REST ON TOP OF COUPLING ON FIXTURE BODY.
proper polarity. 4. SLIP
11. Recess wire connections within junction box.
5. THREAD BRACKET BAR (with installed screws pointed down towards FIXTURE BODY) ONTO WITH lock LOCK 12. RaiseSTEM canopyASSEMBLY and secure inAND place SECURE with (2 provided) balls. WASHER AND NUT. 13. Locate bottom finial disk and thread onto 1/8 IPS at bottom of
6. RAISE FIXTURE AND SECURE BRACKET BAR TO BOX WITH (2 provided) 8-32 SCREWS.
SET SCREW (IN COUPLING)
COUPLING
the fixtureJUNCTION until snug.
ATTACH8-9 GROUND WIRE TO (60 GROUND 14. Install5. (3 provided) watt, E26, LED bulbs. watt ON BRACKET BAR.
SCREW
incandescent equivalent) Then supply power to the fixture.
6. PERFORM WIRE MAKEUP USING (2 provided) WIRE NUTS - ENSURING PROPER POLARITY. 7. RECESS WIRE CONNECTIONS WITHIN JUNCTION BOX. 8. RAISE CANOPY AND SECURE IN PLACE WITH LOCK BALLS.
LAMP
9. INSTALL (3) 7 WATT,LED A19, LAMPS THEN SUPPLY POWER TO THE FIXTURE.
DATE: 08/14/2022
AUTHOR: ERIC MILLER
212.625.9605 | studio@lavivahome.com
HAMMERED COPPER FIXTURE BODY
PAGE 1 OF 2