HANDRAIL & BALUSTRADE EDITION 2020
TUBE & WELD-ON FITTINGS www.keblestrading.com.au
STAINLESS STEEL INFORMATION 1. It is an often held belief that stainless steel is “maintenance free”. This however is not necessarily correct. All grades of stainless steel are susceptible to some form of staining or discolouration and periodic cleaning is required. 2. Stainless steel, if not properly maintained will discolour via a process called tea staining. 3. The staining rate and the required maintenance of stainless steel is relative to its environment, surface finish, design, grade of material and exposure. 4. For example, a. An outside balustrade installation along Melbourne’s Bayside or Coastal Areas would experience a faster rate of tea staining due to the environmental conditions and would therefore require more frequent maintenance than an indoor stairway balustrade installed in an inner Melbourne suburb of say - Blackburn. b. Due to the relative smoothness of the surface finish, a stainless steel component with a satin finish will display signs of tea staining much sooner than a highly polished component of the same grade. c. Designs that incorporate poor run off (rainwater / washing water / etc) provide areas for stagnant water to collect which may increase the likelihood of tea staining. 5. We therefore suggest that you enquire about appropriate products available for the cleaning and maintenance of stainless steel.
DISCLAIMER 1. The above information is only given as a guide or general information. If the information given is insufficient, or if you are not satisfied, or certain, we suggest you seek further advice from a professional metallurgist. 2. For safety, structural and strategic applications, independent engineering or specialist advice should be sought from the relevant authorities/experts. Based on this advice, our sales consultants can assist with the supply of rated fittings for these applications as recommended/nominated by your professional, qualified engineer. Under no circumstances is Keble’s Trading Pty Ltd or its staff authorized or qualified to make any recommendations whatsoever regarding design or selection of fittings for such applications. 3. Keble’s Trading makes no recommendations or claims for the performance and mechanical properties of Stainless Steel and accepts no responsibility or liability whatsoever for any unsatisfactory outcome, unsuitable application or installation of these products. 4. Keble’s Trading Pty Ltd makes no recommendations and takes no responsibility for the use of any fastening system or products used in the installation of any Balustrading and Handrail components. The responsibility of the design and choice of fastener for compliance to Aust Standard and relevant codes lies soley with the purchaser. Please consult appropriate authorities and or the advice of professional persons for information on correct design and installation techniques. 5. While every effort has been made to ensure that all information contained in this brochure is correct at the time of printing, Keble’s Trading Pty Ltd will not be held responsible for any errors, omissions or changes in dimensions at the time or after publication of this brochure. We therefore strongly advise that you check all item details with our sales staff at the time of ordering as changes may occur without prior notice.
2
2020 EDITION
DANDENONG
Call: (03) 9794 5570
CAMPBELLFIELD Call: (03) 9357 9611
LAVERTON NORTH Call: (03) 9314 4599
KILSYTH STH
Call: (03) 9761 4125
info@keblestrading.com.au www.keblestrading.com.au
1 Round Welded Tube ASTM A554
2 Square Welded Tube ASTM A554
3 Rectangular Welded Tube ASTM A554
4 Round Slotted Tube
5 Square Slotted Tube
6 Rectangular Slotted Tube
7 Weld On Tube Joint G304
8 L Bar
9 Wall Bracket with Dynabolt Set
10 Stand-off Handrail Bracket
11 SS Tube Bends
12 SS Tube Bends (Extended One Leg)
13 SS Tube Bends 53º G316
14 Handrail Return 180º G316
15 Tube Clamp
16 Rail Converter G316
Availability and specifications are subject to change without prior notice.
1800 067 687
“We have the right product at the right price, on time every time”
3
17 Bolt Down Adjustable Foot G304
18 Wall Bracket G316
19 Handrail Bracket-Bolt Mount
20 Plate and Cover Set
21 Tube Cover G316
22 Round Base Plate and Cover
23 Round Cover Plate Only
24 SS Mounting Plate 3-Hole G316
25 Long Flange (Cast)
26 Short Flange (Cast)
27 Round Flange
28 Dome End Cap
30 Push End Cap (Cast) G316
31 Sleeve Flange
32 Railing Joint
29 Curved Tube Cap
Availability and specifications are subject to change without prior notice.
4
2020 EDITION
DANDENONG
Call: (03) 9794 5570
CAMPBELLFIELD Call: (03) 9357 9611
LAVERTON NORTH Call: (03) 9314 4599
KILSYTH STH
Call: (03) 9761 4125
info@keblestrading.com.au www.keblestrading.com.au
33 Square Tube Cap
34 Square Base Plate and Cover
35 Square Base Plate and Cover
36 Square Tube Cover
Availability and specifications are subject to change without prior notice.
1800 067 687
“We have the right product at the right price, on time every time”
5
Stainless Steel Round Welded Tube ASTM A554 GRADE 304 TUBE T2 10 1.2 320
SS Tube Round 9.53X1.2MM G304 320 Grit
T2 16 1.2 320
SS Tube Round 15.9X1.2MM G304 320 Grit
T2 16 1.2 320 970
SS Tube Round 15.9x1.2MM G304 320 Grit 970mm
T2 16 1.2 320 990
SS Tube Round 15.9X1.2MM G304 320 Grit 990MM
T2 16 1.2 320 1100
SS Tube Round 15.9X1.2MM G304 320 Grit 1100MM
T2 16 1.5 320 970 I
SS Tube Round 15.9X1.5MM G304 320 Grit 970mm
T2 16 1.5 320 1000 I
SS Tube Round 15.9X1.5MM G304 320 Grit 1000mm
T2 12 1.6 320
SS Tube Round 12.7X1.6MM G304 320 Grit
T2 16 1.6 320
SS Tube Round 15.9X1.6MM G304 320 Grit
T2 19 1.6 320
SS Tube Round 19.05X1.6MM G304 320 Grit
T2 25 1.6 320
SS Tube Round 25.4X1.6MM G304 320 Grit
T2 25 1.6 600
SS Tube Round 25.4X1.6MM G304 600 Grit
T2 32 1.6 320
SS Tube Round 31.7X1.6MM G304 320 Grit
T2 38 1.6 320
SS Tube Round 38.1X1.6MM G304 320 Grit
T2 50 1.6 320
SS Tube Round 50.8X1.6MM G304 320 Grit
T2 50 1.6 600
SS Tube Round 50.8X1.6MM G304 600 Grit
T2 63 1.6 320
SS Tube Round 63.5X1.6MM G304 320 Grit
GRADE 316L TUBE
Other tube sizes available on request
T4L 8 1.2 180
SS Tube Round 7.93X1.2MM G316 Mill Finish
T4L 08 1.6 180
SS Tube Round 7.93X1.6MM G316L 180 Grit
T4L 12 1.6 320
SS Tube Round 12.7X1.6MM G316L 320 Grit
T4L 12 1.6 600
SS Tube Round 12.7X1.6MM G316L 600 Grit
T4L 16 1.6 320
SS Tube Round 15.9X1.6MM G316L 320 Grit
T4L 16 1.6 600
SS Tube Round 15.9X1.6MM G316L 600 Grit
T4L 19 1.6 320
SS Tube Round 19.05X1.6MM G316L 320 Grit
T4L 19 1.6 600
SS Tube Round 19.05X1.6MM G316L 600 Grit
T4L 25 1.6 320
SS Tube Round 25.4X1.6MM G316L 320 Grit
T4L 25 1.6 600
SS Tube Round 25.4X1.6MM G316L 600 Grit
T4L 32 1.6 320
SS Tube Round 31.8X1.6MM G316L 320 Grit
T4L 32 1.6 600
SS Tube Round 31.7X1.6MM G316L 600 Grit
T4L 38 1.6 320
SS Tube Round 38.1X1.6MM G316L 320 Grit
T4L 38 1.6 600
SS Tube Round 38.1X1.6MM G316L 600 Grit
T4L 42 1.6 320
SS Tube Round 42.4x1.6MM G316L 320 Grit
T4L 50 1.6 320
SS Tube Round 50.8X1.6MM G316L 320 Grit
T4L 50 1.6 600
SS Tube Round 50.8X1.6MM G316L 600 Grit
T4L 76 1.6 600
SS Tube Round 76.2X1.6MM G316L 600 Grit
T4L 50 3.0 320
SS Tube Round 50.8X3.0MM G316L 320 Grit
T4L 50 3.0 600
SS Tube Round 50.8X3.0MM G316L 600 Grit
Availability and specifications are subject to change without prior notice.
6
2020 EDITION
DANDENONG
Call: (03) 9794 5570
CAMPBELLFIELD Call: (03) 9357 9611
LAVERTON NORTH Call: (03) 9314 4599
KILSYTH STH
Call: (03) 9761 4125
info@keblestrading.com.au www.keblestrading.com.au
Square Welded Tube ASTM A554 GRADE 304 SQUARE TUBE T2S 16 1.2 180
SS Tube Square 15.9X1.2MM G304 180 Grit
T2S 25 1.2 180
SS Tube Square 25.4X1.2MM G304 180 Grit
T2S 16 1.5 180
SS Tube Square 15.9X1.5MM G304 180 Grit
T2S 12 1.6 180
SS Tube Square 12.7X1.6MM G304 180 Grit
T2S 15 1.6 180
SS Tube Square 15.0X1.6MM G304 180 Grit
T2S 16 1.6 180
SS Tube Square 15.9X1.6MM G304 180 Grit
T2S 19 1.6 180
SS Tube Square 19.05X1.6MM G304 180 Grit
T2S 25 1.6 180
SS Tube Square 25.4X1.6MM G304 180 Grit
T2S 32 1.6 180
SS Tube Square 31.7X1.6MM G304 180 Grit
T2S 38 1.6 180
SS Tube Square 38.1X1.6MM G304 180 Grit
T2S 50 1.6 180
SS Tube Square 50.8X1.6MM G304 180 Grit
T2S 50 3.0 180
SS Tube Square 50.8X3.0MM G304 180 Grit
T2S 100 3.0 180
SS Tube Square 100X100X3MM G304 180 Grit
GRADE 316L SQUARE TUBE T4LS 19 1.6 180
SS Tube Square 19.05X1.6MM G316L 180 Grit
T4LS 25 1.6 180
SS Tube Square 25.4X1.6MM G316L 180 Grit
T4LS 38 1.6 180
SS Tube Square 38.1X1.6MM G316L 180 Grit
T4LS 38 1.6 320
SS Tube Square 38.1X1.6MM G316L 320 Grit
T4LS 38 1.6 600
SS Tube Square 38.1X1.6MM G316L 600 Grit
T4LS 50 1.6 180
SS Tube Square 50.8X1.6MM G316L 180 Grit
T4LS 50 1.6 320
SS Tube Square 50.8X1.6MM G316L 320 Grit
T4LS 50 1.6 600
SS Tube Square 50.8X1.6MM G316L 600 Grit
T4LS 50 3.0 180
SS Tube Square 50.8X3.0MM G316L 180 Grit
T4LS 50 3.0 320
SS Tube Square 50.8X 3.0MM G316L 320 Grit
Other tube sizes available on request
Availability and specifications are subject to change without prior notice.
1800 067 687
“We have the right product at the right price, on time every time”
7
Rectangular Welded Tube ASTM A554 GRADE 304 RECTANGULAR TUBE T2R 5010 1.5 180
SS Tube Rectangular 50X10X1.5MM G304 180 Grit
T2R 4010 1.6 180
SS Tube Rectangular 40X10X1.6MM G304 180 Grit
T2R 5025 1.6 180
SS Tube Rectangular 50X25X1.6MM G304 180 Grit
T2R 5025 1.6 320
SS Tube Rectangular 50x25X1.6MM G304 320 Grit
T2R 6040 1.6 180
SS Tube Rectangular 60x40x1.6MM G304 180 Grit
T2R 7510 1.6 400
SS Tube Rectangular 75X10X1.6MM G304 400 Grit
T2R 7525 1.6 180
SS Tube Rectangular 75X25X1.6MM G304 180 Grit
T2R 8040 1.6 180
SS Tube Rectangular 80X40X1.6MM G304 180 Grit
T2R 10050 2.0 180
SS Tube Rectangular 100X50X2MM G304 180 Grit
T2R 150100 5.0 180
SS Tube Rectangular 150X100X5MM G304 180 Grit
GRADE 316L RECTANGULAR TUBE T4LR 5010 1.5 180
SS Tube Rectangular 50X10X1.5MM G316L 180Grit
T4LR 5010 1.5 320
SS Tube Rectangular 50X10X1.5MM G316L 320 Grit
T4LR 5010 1.5 600
SS Tube Rectangular 50X10X1.5MM G316L 600 Grit
T4LR 5025 1.6 180
SS Tube Rectangular 50X25X1.6MM G316L 180 Grit
T4LR 5025 1.6 320
SS Tube Rectangular 50X25X1.6MM G316L 320 Grit
T4LR 5025 1.6 600
SS Tube Rectangular 50X25X1.6MM G316L 600 Grit
Other tube sizes available on request
Availability and specifications are subject to change without prior notice.
8
2020 EDITION
DANDENONG
Call: (03) 9794 5570
CAMPBELLFIELD Call: (03) 9357 9611
LAVERTON NORTH Call: (03) 9314 4599
KILSYTH STH
Call: (03) 9761 4125
info@keblestrading.com.au www.keblestrading.com.au
Round Slotted Tube G316 TUBE ROUND SLOTTED SINGLE PN
W (slot)
DESCRIPTION
T4LSS 25 1.5 320
14mm
SS Tube R/Slot Single 25.4X1.5MM G316L 320 Grit
T4LSS 25 1.5 600
14mm
SS Tube R/Slot Single 25.4X1.5MM G316L 600 Grit
T4LSS 38 1.5 320
15mm
SS Tube R/Slot Single 38.1X1.5MM G316L 320 Grit
T4LSS 38 1.5 600
15mm
SS Tube R/Slot Single 38.1X1.5MM G316L 600 Grit
T4LSS 38 1.5 600
15mm
SS Tube R/Slot Single 38x1.5MM G316L 600 Grit
T4LSS 38 1.5 320
15mm
SS Tube R/Slot Single 38x1.5MM G316L 320 Grit
T4LSS 50 1.5 600
15mm
SS Tube R/Slot Single 50.8X1.5MM G316L 600 Grit
T4LSS 50 1.5 320
15mm
SS Tube R/Slot Single 50.8X1.5MM G316L 320 Grit
T4LSS 42 1.6 320 I
24mm
SS Tube R/Slot Single 42.4x1.6MM G316L 320 Grit
TUBE ROUND SLOTTED DOUBLE T4LSD 50 1.5 320
15mm
SS Tube R/Slot Dble 50.8X1.5MM G316L 320 Grit
T4LSD 50 1.5 600
15mm
SS Tube R/Slot Dble 50.8X1.5MM G316L 600 Grit
TUBE ROUND SLOTTED 90 DEGREE T4LS90 50 1.5 320
15mm
SS Tube R/Slot Dble 90 Deg 50.8X1.5MM G316L 320 Grit
T4LS90 50 1.5 600
15mm
SS Tube R/Slot Dble 90 Deg 50.8X1.5MM G316L 600 Grit
Other tube sizes available on request
Square Slotted Tube TUBE SQUARE SLOTTED SINGLE T4LSSS 50 1.5 320 I
15mm SS Tube Square Slot/Single 50.8X1.5MM G316 320 Grit
T4LSSS 50 1.5 600 I
15mm SS Tube Square Slot/Single 50.8X1.5MM G316 600 Grit
TUBE SQUARE SLOTTED DOUBLE T4LSSD 50 1.5 320 I
15mm SS Tube Square Slot/Dble 50.8X50.8X1.5MM G316 320 Grit
T4LSSD 50 1.5 600 I
15mm SS Tube Square Slot/Dble 50.8X50.8X1.5MM G316 600 Grit
TUBE SQUARE SLOTTED 90 DEGREE T4LSS90 50 1.5 320
15mm SS Tube Square Slot/Dble 90 Deg 50.8X1.5MM G316 320 Grit
T4LSS90 50 1.5 600
15mm SS Tube Square Slot/Dble 90 Deg 50.8X1.5MM G316 600 Grit
Other tube sizes available on request
Rectangular Slotted Tube GRADE 316L SLOTTED TUBE T4LRSS 2521 1.2 320
14mm SS Tube Slotted 25X21X1.2MM G316L 320 Grit
T4LRSS 2521 1.2 600
14mm SS Tube Slotted 25X21X1.2MM G316L 600 Grit
T4LRSS 5025 1.5 180
15mm SS Tube Slotted 50.8X25.4X1.5MM G316L 180 Grit
T4LRSS 5025 1.5 320
15mm SS Tube Slotted 50.8X25.4X1.5MM G316L 320 Grit
T4LRSS 5025 1.5 600
15mm SS Tube Slotted 50.8X25.4X1.5MM G316L 600 Grit
Other tube sizes available on request Availability and specifications are subject to change without prior notice.
1800 067 687
“We have the right product at the right price, on time every time”
9
Round Handrail Fittings - Weld On Tube Joint G304 PN
SIZE
L (mm)
D (mm)
3000
1 1/2"
114
35
3001
2"
148
48
L Bar G316 PN
SIZE
3034
12mm
L1 (mm) L2 (mm) D (mm) 86
57
12
SS Threaded L Bar PN
Size
Thread
6092
12mm
M8
Wall Bracket with Dynabolt Set PN
DESCRIPTION
04DNB1050
Dynabolt without Wash and Nut 10x50 (55)
16WBTS12
Wall Bracket & Dynabolt Set of Three
6873
Dynabolt Galv with Nut M8x85
6093
Flat Bracket Cover with 9mm Hole
Stand-off Handrail Bracket PN
D
d
H
B
L
FINISH
6385i
38
12
82
8
45
SATIN
6385Mi
38
12
82
8
45
MIRROR
Availability and specifications are subject to change without prior notice.
10
2020 EDITION
DANDENONG
Call: (03) 9794 5570
CAMPBELLFIELD Call: (03) 9357 9611
LAVERTON NORTH Call: (03) 9314 4599
KILSYTH STH
Call: (03) 9761 4125
info@keblestrading.com.au www.keblestrading.com.au
SS Tube Bends PN
TUBE
ANGLE
GRADE
FINISH
6684
2”
45°
G304
SATIN
3784 i
4”
45°
G304
SATIN
3780 i
3/4”
90°
G304
SATIN
6720
1”
90°
G304
SATIN
6759
1 1/4”
90°
G304
SATIN
6420
1 1/2”
90°
G304
SATIN
6370
2”
90°
G304
SATIN
6665
2 1/2”
90°
G304
SATIN
8284
3"
90°
G304
SATIN
3782 i
4”
90°
G304
SATIN
6794
1 1/4”
180°
G304
SATIN
6421
1 1/2”
180°
G304
SATIN
6368
2”
180°
G304
SATIN
3783 i
4”
180°
G304
SATIN
6496
3/4”
90°
G316
SATIN
6497
1”
90°
G316
SATIN
6498
1 1/4”
90°
G316
SATIN
6418
1 1/2”
90°
G316
SATIN
6369
2”
90°
G316
SATIN
6792
2 1/2”
90°
G316
SATIN
6415
1 1/4”
180°
G316
SATIN
6419
1 1/2”
180°
G316
SATIN
6337
2”
180°
G316
SATIN
6793
2 1/2”
180°
G316
SATIN
Availability and specifications are subject to change without prior notice.
1800 067 687
“We have the right product at the right price, on time every time”
11
Tube Bends (Extended One Leg) G304 / 316
PN G304
PN G316
LEG A LEG B mm mm
OD
C.L.R.
31.8mm
57.1
413
93
Satin
6610 SR i 6611 SR i
38.1mm
57.2
426
87
Satin
6610 LR
6611 LR
38.1mm
76.2
426
106
Satin
6610 LR i
6611 LR i
38.1mm
76.2
445
106
Satin
6416
6417
50.8mm
76.2
475
106
Satin
6416 i
6417 i
50.8mm
76.2
456
106
Satin
N/A
8006
FINISH
Tube Bend 53º G316 PN 6612M
TUBE
FINISH
2”
Mirror
Availability and specifications are subject to change without prior notice.
12
2020 EDITION
DANDENONG
Call: (03) 9794 5570
CAMPBELLFIELD Call: (03) 9357 9611
LAVERTON NORTH Call: (03) 9314 4599
KILSYTH STH
Call: (03) 9761 4125
info@keblestrading.com.au www.keblestrading.com.au
Handrail Return Bend 180º G316 PN
TUBE
FINISH
6281I
2”
Satin
6281M
2”
Mirror
Tube Clamp PN
Size
3039
1/2”
SS Tube Clamp (13MM) G304
3040
3/4”
SS Tube Clamp (19MM) G304
3041
1”
SS Tube Clamp (25MM) G304
3042
1 1/4”
SS Tube Clamp (32MM) G304
3043
1 1/2”
SS Tube Clamp (38MM) G304
3044
2”
SS Tube Clamp (51MM) G304
3045
2 1/2”
SS Tube Clamp (63MM) G304
PN
Size
D1 (mm)
D2 (mm)
d1 (mm)
d2 (mm)
L1 L2 (mm) (mm)
H Finish (mm)
3049
1 1/2”
38.1
35
15
10
35
10
50
Satin
3049M
1 1/2”
38.1
35
15
10
35
10
50
Mirror
3035
2”
50.8
47.8
18
13
45
10
62
Satin
3035M
2”
50.8
47.8
18
13
45
10
62
Mirror
6813
2” Tall
50.8
47.8
16 Solid
16 Solid
75
10
92
Satin
Rail Converter G316
Availability and specifications are subject to change without prior notice.
1800 067 687
“We have the right product at the right price, on time every time”
13
Bolt Down Adjustable Foot G304
PN
SIZE
D (mm)
M (mm)
H (mm)
L (mm)
3036
M10x50
55
10
15
60
3037
M12x50
65
12
18
68
3038
M16x60
80
16
22
84
Wall Bracket G316 / Wall Bracket Cover Wall Bracket PN
SIZE
H1 (mm)
H2 (mm)
L
L (mm)
3056
12mm
6
90
56
60
3056M
Mirror Finish
Wall Bracket Cover PN
SIZE
D (mm)
d (mm)
L
L (mm)
3057
12mm
70
12
56
60
3057M
Mirror Finish
Handrail Bracket-Bolt Mount G316 PN
TUBE O
FINISH
6397
N/A
SATIN
6397M
N/A
MIRROR
Availability and specifications are subject to change without prior notice.
14
2020 EDITION
DANDENONG
Call: (03) 9794 5570
CAMPBELLFIELD Call: (03) 9357 9611
LAVERTON NORTH Call: (03) 9314 4599
KILSYTH STH
Call: (03) 9761 4125
info@keblestrading.com.au www.keblestrading.com.au
Plate and Cover Set (Light Duty) (Cover G316, Base Plate G304) PN
SIZE
BASE (mm)
Cover (mm)
D
d
H
TH
D
d
H
TH
3002
1\2”
65
13
6
2
67
13
15
1
3002M
1\2”
65
13
6
2
67
13
15
1
3003
3\4”
65
19
5.5
2
67
19
15
1
3004
1”
65
25
5.5
2
67
25
15
1
3004M
1”
65
25
5.5
2
67
25
15
1
3005
1 1/4”
80
32
6.5
2
82
32
17
1
3006
1 1/2”
80
38
6
2
82
38
17
1
3006M
1 1/2”
80
38
6
2
82
38
17
1
3007
2”
100
51
8
3
102
51
25
1
3007M
2”
100
51
8
3
102
51
25
1
3008
2 1/2”
115
63.5
8
3
117
63.5
28
1
3009
3”
115
76
6
6
117
76
27
1
PN
SIZE
D
d
H
TH
3010
3” - 1 1/2"
79
38
7
1.5
3010M
3” - 1 1/2"
79
38
7
1.5
3011
4” - 2”
101
52
9
1.5
3011M
4” - 2”
101
52
9
1.5
Tube Cover G316
Round Base Plate and Cover (Heavy Duty) (Cover G316, Base Plate G304)
PN
TUBE
DESCRIPTION
FINISH
2673
1 1/2”
3 Hole
Satin
2673MI
1 1/2”
3 Hole
Mirror
6319i
2”
3 Hole
Satin
6319Mi
2”
3 Hole
Mirror
6324i
2”
4 Hole
Satin
6324Mi
2”
4 Hole
Mirror
Availability and specifications are subject to change without prior notice.
1800 067 687
“We have the right product at the right price, on time every time”
15
Round Cover Plate Only G316 PN
TUBE
A
B
H
I
FINISH
3006C
1 1/2"
82
0.8
17
38.4
Satin
3006CM
1 1/2"
79
38
7
1.5
Mirror
3007C
2”
102
0.8
26
51.2
Satin
3007CM
2”
102
0.8
26
51.2
Mirror
Mounting Plate 3-Hole G316
PN
FINISH
6327
Satin
6327M
Mirror
Long Flange (Cast) G316 PN
SIZE
D1 (mm)
D2 (mm)
W (mm)
L (mm)
H (mm)
3012
2” (51mm)
54
51
64
103
13
PN
SIZE
D1 (mm)
D2 (mm)
W (mm)
L (mm)
H (mm)
h (mm)
3013
2” (51mm)
54
51
64
84
13
8
Short Flange (Cast) G316
Availability and specifications are subject to change without prior notice.
16
2020 EDITION
DANDENONG
Call: (03) 9794 5570
CAMPBELLFIELD Call: (03) 9357 9611
LAVERTON NORTH Call: (03) 9314 4599
KILSYTH STH
Call: (03) 9761 4125
info@keblestrading.com.au www.keblestrading.com.au
Round Flange G316 PN
SIZE
D (mm)
d (mm)
H (mm)
T (mm)
3058
2” (51mm)
99
51.8
10
7
12mm
70
7.5
5
3058M
Mirror Finish
6109 6109M
12
Mirror Finish
Dome End Cap G316 PN
SIZE
D (mm)
H (mm)
TH (mm)
3019
3/4” (19mm)
19
10
1.5
3020
1” (25mm)
25
13
1.5
3021
1 1/4” (32mm)
32
16
1.5
3022
1 1/2” (38mm)
38
20
1.5
3023
2” (51mm)
51
25
1.5
3024
2 1/2” (63mm)
63
32
1.5
3025
3” (76mm)
76
38
1.5
3026
4” (101mm)
101
51
1.5
3048
5” (127mm)
127
64
1.5
PN
SIZE
D (mm)
H (mm)
TH (mm)
3027
1 1/2” (38mm)
38
7
1.5
3028
2” (51mm)
51
9
1.5
3029
2 1/2” (63mm)
63
10.5
1.5
Curved End Cap G316
3030
3” (76mm)
76
11.5
1.5
3031
4” (101mm)
101
12.5
1.5
PN
SIZE
D (mm)
d (mm)
H (mm)
L (mm)
3703
1” (25.4mm)
25
22
13
8
3014
1 1/4” (38mm)
32
29
18
12.5
3015
1 1/2” (38mm)
38
35
15
10
3015M
1 1/2” (38mm)
38
35
15
10
3016
2” (51mm)
51
48
16
10
3016M
2” (51mm)
51
48
16
10
3017
2 1/2” (63mm)
63
60
17
12
3018
3” (76mm)
76
73
22
12
Push End Cap (Cast) G316
Availability and specifications are subject to change without prior notice.
1800 067 687
“We have the right product at the right price, on time every time”
17
Sleeve Flange G316 PN
SIZE
D (mm)
D1 (mm)
d (mm)
H (mm)
h (mm)
16SFL51
2”
75
54
51.8
40
34
1 1/2”
60
35
29
d (mm)
TH (mm)
16SFL51M 16SFL38
Mirror Finish 41.5
16SFL38M
38.1
Mirror Finish
Railing Joint G304 PN
D (mm)
Size
04RJS2
Single Hole 2"
51
1.6
04RJS1.5
Single Hole 1 1/2”
38
1.6
04RJD1.5”/1.5”
Double Hole 1 1/2”-1 1/2”
38
38
1.6
04RJD2”/1.5”
Double Hole 2"-1 1/2”
51
38
1.6
04RJD2”/2”
Double Hole 2" -2"
51
51
1.6
PN
SIZE
L (mm)
L1 (mm)
H (mm)
TH (mm)
3055
2”
51.5
20
10
1.5
Square Tube Cap G316
Availability and specifications are subject to change without prior notice.
18
2020 EDITION
DANDENONG
Call: (03) 9794 5570
CAMPBELLFIELD Call: (03) 9357 9611
LAVERTON NORTH Call: (03) 9314 4599
KILSYTH STH
Call: (03) 9761 4125
info@keblestrading.com.au www.keblestrading.com.au
Light Duty Square Plate and Cover (Cover G316, Base Plate G304) PN
TUBE
GRADE COVER
GRADE PLATE
FINISH
6786
1 1/2”
316
304
Satin
6786M
1 1/2”
316
304
Mirror
3570
2”
316
304
Satin
3570M
2”
316
304
Mirror
Heavy Duty Square Base Plate and Cover (Cover G316, Base Plate G304)
PN
TUBE
GRADE COVER
GRADE BASE
6613
2”
316
304
6613M
2”
316
304
Square Tube Cover G316 PN
SIZE
D mm
d mm
H mm
TH mm
3032
3”- 1 1/2“
76.2
3033
4” - 2”
102
38.2 x 38.2
7
1.2
38.2 x 38.2
9.5
1.5
Availability and specifications are subject to change without prior notice.
1800 067 687
“We have the right product at the right price, on time every time”
19
KT DANDENONG 1/28 Johnston Crt, Dandenong VIC, Australia, 3175 Call: (03) 9794 5570
KT CAMPBELLFIELD 6/1880 Hume Highway, Campbellfield VIC , Australia, 3061 Call: (03) 9357 9611
KT LAVERTON NORTH Unit 1, 94 Boundary Road, Sunshine West VIC, Australia, 3020 Call: (03) 9314 4599
KT KILSYTH 1/120-122 Canterbury Rd, Kilsyth South VIC , Australia, 3137 Call: (03) 9761 4125
WE ALSO SPECIALISE IN THE FOLLOWING
BALUSTRADES
LIFTING
WIRE ROPE
www.keblestrading.com.au
RIGGING