International Research Journal of Engineering and Technology (IRJET)
e-ISSN: 2395-0056
Volume: 10 Issue: 06 | June 2023
p-ISSN: 2395-0072
www.irjet.net
Pushover analysis of setback frame & step frame building with and without shear wall by using ETABS Jigna Chudasama1, Aakash Suthar2 1 Student of Master of Engineering, Ahmedabad, Dept. of Structure Engineering, L.J. University, Gujarat, India 2Assitant professor, Ahmedabad, Dept. of Structure Engineering & Technology, Gujarat, India
---------------------------------------------------------------------***---------------------------------------------------------------------
Abstract - This study focuses on the pushover analysis (Nonlinear Static Analysis) of structure. The current building codes and design standards only offer a small amount of performance-based or prescriptive advice on the study and design of structures. And give overviews on the pushover analysis of setback frame & step frame buildings. And also analyze and design of setback frame & step frame building with G+5 story. The durability and economy of the structure are the focus of this article. For the current study, basic parameter including story drift, base shear and story displacement were examined. Along with guidelines of IS 875, analysis of building is done considering dead load, live load depending upon the requirement and function of the structure.
setbacks fall in during extreme ground shaking and cause direct scattering of individual lives. Over the past few years, various investigation has been carried out internationally to determine the cause of the failure of various types of designs under extreme significant stress. Its discontinuity in the arrangement is one of the crucial probabilities for the failure labor of the RC multi story construction. 1.1 What are Vertical Geometric Irregularities? In IS 1893(part 1): 2016, three types of mathematical constructions are shown, including the step frame, set back frame and floating column. The earthquake impacts of designs with vertically geometrical irregularity and located in seismic zine III, IV, and V will be evaluated using the investigation strategy.
Key Words: Seismic analysis, Pushover analysis, Setback & Step Building, Vertical geometric Irregularities, Basement Wall, Shear Wall, ETABS, Response Spectrum Analysis, Story drift, Story Displacement, Base Shear.
1.INTRODUCTION General It is quite challenging to plan with irregular shapes in today’s world because the great majority of development is set up with structural importance. Because of their functional and fashionable design, irregular shaped constructions are in demand.in the design plan, sidelong forces have a fundamental impact. Because of its irregular behavior and great eradication power, tremor is quite perhaps the most terrible horizontal forces. Building setbacks fall in during extreme ground shaking and cause direct scattering of individual lives. Over the past few years, various investigation has been carried out internationally to determine the cause of the failure of various types of designs under extreme significant stress. Its discontinuity in the arrangement is one of the crucial probabilities for the failure labor of the RC multi story construction. It is quite challenging to plan with irregular shapes in today’s world because the great majority of development is set up with structural importance.
1.2 Fig 1.1: Vertical Geometric Irregularity as per IS 1893(Part 1) – 2016 Pushover Analysis To determine the estimated seismic requirements for building structures of non-linear static analysis or pushover analysis is used more and more. Since buildings display nonlinear behavior during earthquakes, nonlinear analysis must be used to determine whether or not the structure is performing as desired. One of the most significant study areas in seismic engineering over the past ten years has been the performance-based design (PBD) technique. Determining the desired deformation for every resisting element until its failures allows the nonlinear static evaluation of the asymmetric buildings to take the torsion effects into account. Once the target displacement is obtained, the base shear is applied in increasing amounts.
Because of their functional and fashionable design, irregular shaped constructions are in demand.in the design plan, sidelong forces have a fundamental impact. Because of its irregular behavior and great eradication power, tremor is quite perhaps the most terrible horizontal forces. Building
© 2023, IRJET
|
Impact Factor value: 8.226
|
ISO 9001:2008 Certified Journal
|
Page 78