10
IV
https://doi.org/10.22214/ijraset.2022.41905
April 2022
International Journal for Research in Applied Science & Engineering Technology (IJRASET) ISSN: 2321-9653; IC Value: 45.98; SJ Impact Factor: 7.538 Volume 10 Issue IV Apr 2022- Available at www.ijraset.com
Matlab Simulation for Power Factor Correction Vishwanath Chalawadi1, Sanjeeth P. Amminabhavi2 1
2
Student, Electrical and Electronics Department SDMCET, Dharwada, India Assistant Prof., Electrical and Electronics Department SDMCET Dharwad, India
Abstract: Lower in Power Factor of electrical equipments will draws high current from supply power. The effect of this is affected by impedance of electrical equipment. Therefore, the main consideration of this study is how impedance of electrical equipment affects the power factor of electrical loads, and then distributed power as the whole. This study is important to verify the right action to increase low power factor effectively for electrical energy efficiency concern. I. INTRODUCTION Power factor (PF) is the ratio of Real power, measured in kilowatts (kW), to apparent power, measured in kilovolt amperes (kVA) or also known as demand. It will get by multiplying [kVA=V*A]. The result will be in kVA units. A. Power factor basics Power quality will efficient for equipment operation, it is one of the advantage of power factor. Power factor will gives the detail about how efficiently input power is used in an electrical installation. It is the ratio of Real power to apparent power, When, Active Power (P) = the power required for useful work, SI unit is Watt or KiloWatt (kW). Reactive Power (Q) = It is the stored energy effected to the source, SI unit is var or Kilovar (kVAR) Apparent Power (S) = the vector sum of active and reactive power, SI unit is Volt Amperes or in KiloVolt Amperes (kVA)
Fig.1.The power triangle
©IJRASET: All Rights are Reserved | SJ Impact Factor 7.538 | ISRA Journal Impact Factor 7.894 |
7
International Journal for Research in Applied Science & Engineering Technology (IJRASET) ISSN: 2321-9653; IC Value: 45.98; SJ Impact Factor: 7.538 Volume 10 Issue IV Apr 2022- Available at www.ijraset.com B. Correction of Power Factor The main aim of Power factor correction (PFC) is to improve power factor, and also reduces the load acts on the distribution system, increases energy efficiency and reduces costs of electricity . It also decreases the instability and failure of system components. Power factor correction is nothing but connecting the capacitors which produce reactive. Electrical Energy in opposition to the Electrical Energy absorbed by loads like motors, nearly close to the load. It improves the power factor where the reactive power source is connected.
1) Example Problem For Power Factor Correction (Question)A three phase static load takes real power of 10kWand reactive power of 5kVAR from a three phase two winding transformer (11/0.415kV,25MVA). The HV side of transformer connected to 11kV ,50Hz three phase supply .[1].Calculated power factor of the load ? [2].Calculate the capacitor bank (capacitive VAR) required to maintain the power factor of 0.95 at load side ? 2) Solution Power Factor = Power Factor =
( ) ( )
=
= 0.8944
3) Capacitor bank required to maintain 0.95p.f Q rating of capacitor bank at load sisde = P tan(actual pf angle–required pf angle) =10*tan(Acos(0.8944) – cos(0.95)) =10*tan(26.5685 – 18.1949) Q rating of capacitor bank at load side =1.472 kVAR. Q rating of capacitor bank at load side =1.472 kVAR. C. System Parameters 1) Three phase source :11kV,50Hz 2) Transformer :11kV /0.415kV ,25MVA 3) Load details 10KW ,5 kVAR 4) Line length:10m
©IJRASET: All Rights are Reserved | SJ Impact Factor 7.538 | ISRA Journal Impact Factor 7.894 |
2789
International Journal for Research in Applied Science & Engineering Technology (IJRASET) ISSN: 2321-9653; IC Value: 45.98; SJ Impact Factor: 7.538 Volume 10 Issue IV Apr 2022- Available at www.ijraset.com II.
MATLAB SIMULATION MODEL
Fig.2.Simulation model without capacitor bank The above figure shows the practical MATLAB simulation of the model. It contains generation system and output of the generator is connected to the 11kV/415v, 25MVA and the secondary of the transformer is transmitted through the transmission line and the output supply is connected the R-L load of 10kw,5 kvar which drawing the power factor the 0.8944 to improve the power factor of the system the calculation the capacitor bank should be required. In the above system there is no capacitor bank in between load and transmission line
©IJRASET: All Rights are Reserved | SJ Impact Factor 7.538 | ISRA Journal Impact Factor 7.894 |
2790
International Journal for Research in Applied Science & Engineering Technology (IJRASET) ISSN: 2321-9653; IC Value: 45.98; SJ Impact Factor: 7.538 Volume 10 Issue IV Apr 2022- Available at www.ijraset.com
Fig.3.Simulation model with capacitor bank After calculating the capacitor value it will be inserted in between the line and load the power factor of the system will improved to 0.9pf . The below figures of wave forms will gives the values of terminal voltage and current.
Fig.4.Generation voltage
©IJRASET: All Rights are Reserved | SJ Impact Factor 7.538 | ISRA Journal Impact Factor 7.894 |
2791
International Journal for Research in Applied Science & Engineering Technology (IJRASET) ISSN: 2321-9653; IC Value: 45.98; SJ Impact Factor: 7.538 Volume 10 Issue IV Apr 2022- Available at www.ijraset.com
Fig.4.Input current III. CONCLUSION In this paper author will discussed about the basic introduction about the power factor and also short description about the power factor correction. For the power factor correction author will taking the real time problem as a problem statement and also calculated the theoretical calculation as well as simulated the practical model in the mat lab simulation and the values of capacitor bank(kVar) will be verified and observed the with capacitor and without capacitor condition of the power factor. REFERENCES [1] [2] [3]
Osama A. Al-Naseem and Ahmad Kh. Adi, Impact of Power Factor Correction on the Electrical Distribution Networkof Kuwait –A Case Study, OJPEE Volume (2), Number (1), Reference Number: W10-0030, Page 173-176, January 2011 Gagari Deb, Partha Sarathi Saha and Prasenjit Das, A Method of Finding Capacitor Value for Power Factor Improvement, International Journal of Electrical Engineering, ISSN 0974-2158 Volume 4, Number 8 (2011), pp. 913- 922, © International Research Publication House, 2011 B. Sharifipour, J. S. Huang, P. Liao, L. Huber, and M. M. Jovanovic, Manufacturing and Cost Analysis of Power-Factor-Correction Circuit, IEEE Applied Power Electronics Conf. (APEC) Proc., Anaheim, CA, Feb. 15-19, 1998, pp. 490-494, 1998
©IJRASET: All Rights are Reserved | SJ Impact Factor 7.538 | ISRA Journal Impact Factor 7.894 |
2792