CONTENTS
CONTENTS Pagina
10. STRUCTURE AND FUNCTION ...................................................................................... 10-1 20. TESTING AND ADJUSTING ........................................................................................... 20-1 30. DISASSEMBLY AND ASSEMBLY ................................................................................. 30-1 90. OTHER...................................................................................................................... 90-1
WH6 - WH7
00-1
PAGE INTENTIONALLY LEFT BLANK
REVISED PAGES
REVISED PAGES The affected pages are indicated by the use of the following marks. It is requested that necessary actions be taken to these pages according to table below.
Mark
Indication
Action required
Q
Page to be newly
Add
q
Page to be replaced
Replace
( )
Page to be delete
Discard
Pages having no marks are those previously revised or made additions. Mark
Page
00-1 00-2 00-3 00-4 00-5 00-6 00-7 00-8 00-9 00-10 00-11 00-12 00-13 00-14 00-15 00-16 00-17 00-18 00-19 00-20 00-21 00-22 00-23 00-24 10-1 10-2 10-3 10-4 10-5 10-6 10-7 10-8 10-9 10-10 10-11 10-12 10-13 10-14 10-15
WH6 - WH7
Time of Mark revision
Page
10-16 10-17 10-18 10-19 10-20 10-21 10-22 10-23 10-24 10-25 10-26 10-27 10-28 10-29 10-30 10-31 10-32 10-33 10-34 10-35 10-36 10-37 10-38 10-39 10-40 10-41 10-42 10-43 10-44 10-45 10-46 10-47 10-48 10-49 10-50 10-51 10-52 10-53 10-54 10-55 10-56 10-57 10-58
Time of Mark revision
Page
10-59 10-60 10-61 10-62 10-63 10-64 10-65 10-66 10-67 10-68 10-69 10-70 10-71 10-72 10-73 10-74 10-75 10-76 10-77 10-78 10-79 10-80 10-81 10-82 10-83 10-84 10-85 10-86 10-87 10-88 20-1 20-2 20-3 20-4 20-5 20-6 20-7 20-8 20-9 20-10 20-11 20-12
Time of Mark revision
Page
20-13 20-14 20-15 20-16 20-17 20-18 20-19 20-20 20-21 20-22 20-23 20-24 20-25 20-26 20-27 20-28 20-29 20-30 20-31 20-32 20-33 20-34 20-35 20-36 20-37 20-38 20-39 20-40 20-41 20-42 20-43 20-44 20-45 20-46 20-47 20-48 20-49 20-50 20-51 20-52 20-53 20-54 20-55
Time of Mark revision
Page
Time of revision
20-56 20-57 20-58 20-59 20-60 20-61 20-62 20-63 20-64 20-65 20-66 20-67 20-68 20-69 20-70 20-71 20-72 20-73 20-74 20-75 20-76 20-77 20-78 20-79 20-80 20-81 20-82 20-83 20-84 20-85 20-86 20-87 20-88 20-89 20-90 20-91 20-92 20-93 20-94 20-95 20-96 20-97 20-98
00-3
REVISED PAGES
Mark
Page
20-99 20-100 20-101 20-102 20-103 20-104 20-105 20-106 20-107 20-108 20-109 20-110 30-1 30-2 30-3 30-4 30-5 30-6 30-7 30-8 30-9 30-10 30-11 30-12 30-13 30-14 30-15 30-16 30-17 30-18 30-19 30-20 30-21 30-22 30-23 30-24 30-25 30-26 30-27 30-28 30-29 30-30 30-31 30-32 30-33 30-34 30-35 30-36 30-37 30-38 30-39 30-40 30-41 30-42 30-43 30-44 30-45 30-46 30-47 30-48 30-49
00-4
Time of Mark revision
Page
30-50 30-51 30-52 30-53 30-54 30-55 30-56 30-57 30-58 30-59 30-60 30-61 30-62 30-63 30-64 30-65 30-66 30-67 30-68 30-69 30-70 30-71 30-72 30-73 30-74 30-75 30-76 30-77 30-78 30-79 30-80 30-81 30-82 30-83 30-84 30-85 30-86 30-87 30-88 30-89 30-90 30-91 30-92 30-93 30-94 30-95 30-96 30-97 30-98 30-99 30-100 30-101 30-102 30-103 30-104 30-105 30-106 30-107 30-108 30-109 30-110 30-111
Time of Mark revision
Page
30-112 30-113 30-114 30-115 30-116 30-117 30-118 30-119 30-120 30-121 30-122 30-123 30-124 30-125 30-126 30-127 30-128 30-129 30-130 30-131 30-132 30-133 30-134 30-135 30-136 30-137 30-138 30-139 30-140 30-141 30-142 30-143 30-144 30-145 30-146 30-147 30-148 30-149 30-150 30-151 30-152 30-153 30-154 30-155 30-156 30-157 30-158 30-159 30-160 30-161 30-162 30-163 30-164 30-165 30-166 30-167 30-168 30-169 30-170 30-171 30-172 30-173
Time of Mark revision
Page
30-174 30-175 30-176 30-177 30-178 30-179 30-180 30-181 30-182 30-183 30-184 30-185 30-186 30-187 30-188 30-189 30-190 30-191 30-192 30-193 30-194 30-195 30-196 30-197 30-198 30-199 30-200 30-201 30-202 30-203 30-204 30-205 30-206 30-207 30-208 30-209 30-210 30-211 30-212 30-213 30-214 30-215 30-216 30-217 30-218 30-219 30-220 30-221 30-222 30-223 30-224 30-225 30-226 30-227 30-228 30-229 30-230 30-231 30-232 30-233 30-234 30-235
Time of Mark revision
Page
Time of revision
30-236 30-237 30-238 30-239 30-240 30-241 30-242 30-243 30-244 30-245 30-246 30-247 30-248 30-249 30-250 30-251 30-252 30-253 30-254 30-255 30-256 30-257 30-258 30-259 30-260 30-261 30-262 30-263 30-264 30-265 30-266 30-267 30-268 30-269 30-270 30-271 30-272 30-273 30-274 30-275 30-276 30-277 30-278 30-279 30-280 30-281 30-282 30-283 30-284 90-1 90-2 90-3 90-4 90-5 90-6
WH6 - WH7
This is the sample of the manual Click on the download link for complete manual
Download Link
k SAFETY
k IMPORTANT SAFETY NOTICE Proper service and repair is extremely important for the safe operation of your machine. The service and repair techniques recommended by Komatsu Utility and describe in this manual are both effective and safe methods of operation. Some of these operations require the use of tools specially designed by Komatsu Utility for the purpose.
To prevent injury to workers, the symbol k is used to mark safety precautions in this manual. The cautions accompanying these symbols should always be carefully followed. If any danger arises or may possibly arise, first consider safety, and take necessary steps to face.
GENERAL PRECAUTIONS
k SAFETY
Mistakes in operation extremely dangerous. Read all the Operation and Maintenance Manual carefully BEFORE operating the machine. 1. Before carrying out any greasing or repairs, read all the precautions written on the decals which are suck on the machine. 2. When carrying out any operation, always wear safety shoes and helmet. Do not wear loose work clothes, or clothes with buttons missing. Always wear safety glasses when hitting parts with a hammer. Always wear safety glasses when grinding parts with a grinder, etc. 3. If welding repairs are needed, always have a trained, experienced welder carry out the work. When carrying out welding work, always wear welding gloves, apron, glasses, cap and other clothes suited for welding work. 4. When carrying out any operation with two or more workers, always agree on the operating procedure before starting. Always inform your fellow workers before starting any step of the operation. Before starting work, hang UNDER REPAIR signs on the controls in the operator s compartment. 5. Keep all tools in good condition and learn the correct way to use them. 6. Decide a place in the repair workshop to keep tools and removed parts. Always keep the tools and parts in their correct places. Always keep the work area clean and make sure that there is no dirt or oil on the floor. Smoke only in the areas provided for smoking. Never smoke while working.
WH6 - WH7
PREPARATIONS FOR WORK 7. Before adding or making any repairs, park the machine on hard, level ground, and block the wheels to prevent the machine from moving. 8. Before starting work, lower outrigger, bucket or any other work equipment to the ground. If this is not possible, use blocks to prevent the work equipment from falling down. In addition, be sure to lock all the control levers and hang warning sign on them. 9. When disassembling or assembling, support the machine with blocks, jacks or stands before starting work. 10. Remove all mud and oil from the steps or other places used to get on and off the machine. Always use the handrails, ladders or steps when getting on or off the machine. Never jump on or off the machine. If it is impossible to use the handrails, ladders or steps, use a stand to provide safe footing.
PRECAUTIONS DURING WORK 11. When removing the oil filler cap, drain plug or hydraulic pressure measuring plugs, loosen them slowly to prevent the oil from spurting out. Before disconnecting or removing components of the hydraulic circuit and engine cooling circuit, first remove the pressure completely from the circuit. 12. The water and oil in the circuits are not hot when the engine in stopped, so be careful not to get burned. Wait for the oil water to cool before carrying out any work on the cooling water circuits. 13. Before starting work, remove the leads from the battery. Always remove the lead from the negative ( ) terminal first.
00-5
k SAFETY
14. When raising heavy components, use a hoist or crane. Check that the wire rope, chains and hooks are free from damage. Always use lifting equipment which has ample capacity. Install the lifting equipment at the correct places. Use a hoist or crane and operate slowly to prevent the component from hitting any other part. Do not work with any part still raised by the hoist or crane. 15. When removing covers which are under internal pressure or under pressure from a spring, always leave two bolts in position on opposite sides. Slowly release the pressure, then slowly loosen the bolts to remove. 16. When removing components, be careful not to break or damage the wiring. Damage wiring may cause electrical fires. 17. When removing piping, stop the fuel or oil from spilling out. If any fuel or oil drips on to the floor, wipe it up immediately. Fuel or oil on the floor can cause you to slip, or can even start fires.
19. Be sure to assemble all parts again in their original places. Replace any damage parts with new parts. When installing hoses and wires, be sure that they will not be damaged by contact with other parts when the machine is being operated. 20. When installing high pressure hoses, make sure that they are not twisted. Damaged tubes are dangerous, so be extremely careful when installing tubes for high pressure circuits. Also, check that connecting parts are correctly tightened. 21. When assembling or installing parts, always use specified tightening torques. When installing the parts which vibrate violently or rotate at high speed, be particulary careful to check that they are correctly installed. 22. When aligning two holes, never insert your fingers or hand. 23. When measuring hydraulic pressure, check that the measuring tool is correctly assembled before taking any measurement. 24. Take sure when removing or installing wheels.
18. As a general rule, do not use gasoline to wash parts. In particular, use only the minimum of gasoline when washing electrical parts.
00-6
WH6 - WH7
FOREWORD
FOREWORD
This shop manual has been prepared as an aid to improve the quality of repairs by giving the operator an accurate understanding of the product and by showing him the correct way to perform repairs and make judgements. Make sure you understand the contents of this manual and use it to full effect at every opportunity. This shop manual mainly contains the necessary technical information for operations performed in a service workshop. The manual is divided into chapters on each main group of components; these chapters are further divided into the following sections. STRUCTURE AND FUNCTION This section explains the structure and function of each component. It serves not only to give an understanding of the structure, but also serves as reference material for troubleshooting. TESTING AND ADJUSTING This sections explains checks to be made before and after performing repairs, as well as adjustments to be made at completion of the checks and repairs. Troubleshooting charts correlating «Problems» to «Causes» are also included in this section. DISASSEMBLY AND ASSEMBLY This section explains the order to be followed when removing, installing, disassembling or assembling each component, as well as precautions to be taken for these operations.
NOTE The specifications contained in this shop manual are subject to change at any time and without any notice. Contact your Komatsu Utility distributor for the latest information.
WH6 - WH7
00-7
HOW TO READ THE SHOP MANUAL
HOW TO READ THE SHOP MANUAL VOLUMES
SYMBOLS
DISTRIBUTION AND UPDATING
Symbol
Shop manual are issued as a guide to carry out repairs. These various volumes are designed to avoid duplicating the same information. Any additions, amendments or other changes will be sent to Komatsu Utility distributors. Get the most up-to-date information before you start any work.
FILING METHOD
k
Item
Special safety precautions are necessary when performing the work. Safety
1. See the page number on the bottom of the page. File the pages in correct order. 2. Following examples show you how to read the page number. Example:
a 4
Remarks
Extra special safety precautions are necessary when performing the work because it is under internal pressure.
Caution
Special technical precautions or other precautions for preserving standards are necessary when performing the work.
Weight
Weight of parts or systems. Caution necessary when selecting hoisting wire, or when working posture is important, etc.
tion for the tightening torque dur3 Tightening torque
Parts that require special atten-
3. Additional pages: additional pages are indicated by a hyphen ( ) and number after the page number. Fle as in the example. Example:
2 5 6
ing assembly.
Coat
Parts to be coated with adhesives and lubricants etc.
Places where oil, water or fuel Oil, water must be added, and their quantity. Drain
Places where oil or water must be drained, and quantity to be drained.
REVISED EDITION MARK
When a manual is revised, an edition mark is recorded on the bottom outside corner of the pages.
REVISIONS
Revised pages are shown on the LIST OF REVISED PAGES between the title page and SAFETY page.
00-8
WH6 - WH7
HOISTING INSTRUCTIONS
HOISTING INSTRUCTIONS
4
Hooks have maximum strength at the middle portion.
k Heavy parts (25 kg or more) must be lifted with a hoist etc. In the Disassembly and Assembly section, every part weighing 25 kg or more is clearly indicated with the symbol 4
1. If a part cannot be smoothly removed from the machine by hoisting, the following checks should be made: Check for removal of all bolts fastening the part to the relative parts. Check for any part causing interference with the part to be removed.
2.
Wire ropes
1)
Use adequate ropes depending on the weight of parts to be hoisted, referring to the table below: WIRE ROPES (Standard «S» or «Z» twist ropes without galvanizing)
Rope diameter (mm)
Allowable load (tons)
10.0
1.0
11.2
1.4
12.5
1.6
14.0
2.2
16.0
2.8
18.0
3.6
20.0
4.4
22.4
5.6
30.0
10.0
40.0
18.0
50.0
28.0
60.0
40.0
3) Do not sling a heavy load with one rope alone, but sling with two or more ropes symmetrically wound on to the load. k Slinging with one rope may cause turning of the load during hoisting, untwisting of the rope, or slipping of the rope from its original winding position on the load, which can cause dangerous accidents. 4)
Do not sling a heavy load with ropes forming a wide hanging angle from the hook. When hoisting a load with two or more ropes, the force subjected to each rope will increase with the hanging angles. The table below shows the variation of allowable load (kg) when hoisting is made with two ropes, each of which is allowed to sling up to 1000 kg vertically, at various handing angles. When two ropes sling a load vertically, up to 2000 kg of total weight can be suspended. This weight becomes 1000 kg when two ropes make a 120° hanging angle. On the other hand, two ropes are subjected to an excessive force as large as 4000 kg if they sling a 2000 kg load at a lifting angle of 150°.
The allowable load value is estimated to be onesixth or one-seventh of the breaking strength of the rope used. 2)
Sling wire ropes from the middle portion of the hook. Slinging near the edge of the hook may cause the rope to slip off the hook during hoisting, and a serious accident can result.
WH6 - WH7
00-9
STANDARD TIGHTENING TORQUE
3
STANDARD TIGHTENING TORQUE
The following charts give the standard tightening torques of bolts and nuts. Exceptions are given in section of «Disassembly and Assembly».
1.
STANDARD TIGHTENING TORQUE OF BOLTS AND NUT Width across flat (mm)
Thread diameter of bolts (mm)
Pitch of bolts (mm)
6
1
10
8
1.25
10
kgm
Nm
kgm
Nm
8
0.96 0.1
9.5 1
1.3 0.15
13.5 1.5
13
6
2.3 0.2
23 2
3.2 0.3
32.2 3.5
1.5
17
8
4.6 0.5
45 4.9
6.5 0.6
63 6.5
12
1.75
19
10
7.8 0.8
77 8
11 1
108 11
14
2
22
12
12.5 1
122 13
17.5 2
172 18
16
2
24
14
19.5 2
191 21
27 3
268 29
18
2.5
27
14
27 3
262 28
37 4
366 36
20
2.5
30
17
38 4
372 40
53 6
524 57
22
2.5
32
17
52 6
511 57
73 8
719 80
24
3
36
19
66 7
644 70
92 10
905 98
27
3
41
19
96 10
945 100
135 15
1329 140
30
3.5
46
22
131 14
1287 140
184 20
1810 190
33
3.5
50
24
177 20
1740 200
250 27
2455 270
36
4
55
27
230 25
2250 250
320 35
3150 350
39
4
60
----
295 33
2900 330
410 45
4050 450
This torque table does not apply to bolts or nuts which have to fasten nylon or other parts non-ferrous metal washer.
a Nm (newton meter): 1 Nm = 0.102 kgm
00-10
WH6 - WH7
STANDARD TIGHTENING TORQUE
3
2.
TIGHTENING TORQUE FOR NUTS OF FLARED
Use these torques for nut part of flared. Thread diameter of nut part (mm)
Width across flats of nut part (mm)
TIGHTENING TORQUE kgm
Nm
1/2 - 20
17
2.6 0.5
25.5 4.9
9/16 - 18
17
4 0.5
39.2 4.9
3/4 - 16
22
6.7 2
65.7 19.6
7/8 - 14
27
8 2
78.5 19.6
1.1/16 - 12
32
9.7 3
95.15 29.4
1.5/16 - 12
38
17 3
166.7 29.4
1.5/8 - 12
50
20 5
196.2 49
22
27
8 2
78.5 19.6
33
41
20 5
196.2 49
Sealing surface
Thread diameter of nut part (mm)
Width across flats of nut part (mm)
kgm
Nm
9/16 - 18
17
2.3 2.5
23 25
11/16 - 16
22
3.4 3.9
33 38
13/16 - 16
24
5.2 5.8
51 57
1 - 14
30
8.2 9.2
80 90
1.3/16 - 12
36
12.2 13.3
120 130
1.7/16 - 12
41
15.3 17.3
150 170
1.11/16 - 12
50
18.4 20.4
180 200
2 - 12
57
20.4 24.4
200 240
WH6 - WH7
TIGHTENING TORQUE
00-11
COATING MATERIALS
2 COATING MATERIALS
The recommended coating materials prescribed in Komatsu Utility Shop Manuals are listed below: Nomenclature
Code
Applications
ASL800010 Used to apply rubber pads, rubber gaskets and cork plugs.
Adhesives
Gasket sealant
ASL800020
Used to apply resin, rubber, metallic and non-metallic parts when a fast, strong seal is needed.
Loctite 222
Used for low resistance locking of screws, check nuts and adjustment nuts.
Loctite 242
To prevent the loosening of bolts, nuts and plugs and the leakage of oil. Used for medium resistance locking of screws and nuts of every type, and for locking keys and bearings.
Loctite 262
Used for high resistant of threaded parts that can be removed with normal tools.
Loctite 270
Used for high resistant locking and for sealing threaded parts, bolts and stud bolts.
Loctite 542
Used for sealing the union threads for hydraulic tubes.
Loctite 573
Used for sealing rather exact plane surfaces when the option of possible future dismantling is required.
Loctite 601
Used for high resistant locking of mechanical components that can be removed only after heating
Loctite 675
Used to lock cylindrical couplings and for the permanent locking of threaded parts, and also to lock shafts to bearings, gears, pulleys, pins, bushings, etc.
ASL800060
Used by itself to seal grease fittings, tapered screw fittings and tapered screw fittings in hydraulic circuits of less than 50 mm in diameter.
Loctite 510
Used by itself on mounting flat surface (Clearance between surfaces within 0.2 mm)
Loctite 518
Used by itself on mounting flat surface (Clearance between surfaces within 0.5 mm
Antifriction compound Applied to bearings and taper shaft to facilitate press-fitting and to prevent (Lubricant including ASL800040 sticking, burning or rusting. Molybdenum disulfide) Grease (Lithium grease) Vaseline
00-12
ASL800050
-----
Applied to bearings, sliding parts and oil seals for lubrication, rust prevention and facilitation of assembling work. Used for protecting battery electrode terminals from corrosion
WH6 - WH7
ELECTRIC
ELECTRIC
ELECTRIC
In the wiring diagrams various colour and symbols are employed to indicate the thickness of wires. This wire code table will help you understand WIRING DIAGRAMS. Example: R N 1.5 indicates a cable having a nominal number 1.5 and red coating with black stripe.
CLASSIFICATION BY THICKNESS Nominal number
Number strands 16 14 21 35 56 84 84 399
0.5 1 1.5 2.5 4 6 10 50
Copper wire Ø of strands (mm) 0.20 0.30 0.30 0.30 0.30 0.30 0.40 0.40
Cross section (mm) 0.35 0.99 1.48 2.47 3.95 5.93 10.55 50.11
Cable O.D. (mm)
Current rating (A)
1.55 2.80 3.35 3.80 4.60 5.20 7.10 14
3.5 11 14 20 28 37 53 160
CLASSIFICATION BY COLOUR AND CODE Primary Code Colour
A
Auxiliary A B
A/B
A G
A N
A/N
Light Blue Light Blue White Light Blue Yellow Light Blue Black
Code
B
Colour
White
Code
C
Colour
Orange
Code
G
Colour
Yellow
B G
B N
B/N
B R
B/R
A R
A/R
Light Blue Red
B/V
White Yellow
White Black
White Red
White Green
C B
C L
C N
C/B
Orange White
Orange Blue
G N
G R
G/N
Yellow Black
Yellow Red
H L
H N
H/N
Orange Black G V
H
Colour
Grey
Code
L
Colour
Blue
Blue White
Blue Yellow
Blue Black
Code
M
M B
M N
M V
Colour
Brown
Code
N
Colour
Black
Grey Blue
Grey Black
L B
L G
L/B
M/N
Brown White
Brown Black
L/N
R
R G
Red
Red Yellow
Red Black
Red Green
Code
S
S G
S N
Colour
Pink
Pink Yellow
Pink Black
Code
V
V B
V N
Colour
Green
Code
Z
Colour
Violet
V/N
Green White
Green Black
Z B
Z N
Z/B
Violet White
Z/N
Violet Black
R V
Colour
R/N
Brown Green
Code
R N
A/V
Light Blue Green
Yellow Green
Code
A V
COMPOSITION OF THE COLOURS
The coloration of two-colour wires is indicated by the composition of the symbol listed. Example: G V = Yellow-Green with longitudinal colouring G/V = Yellow-Green with transversal colouring
WH6 - WH7
00-13