CEBM001801
WA250-3PTC
SHOP MANUAL WA250-3 Parallel Tool Carrier MACHINE MODEL
SERIAL NUMBERS
WA250-3
A75001 and up
This material is proprietary to Komatsu America International Company and is not to be reproduced, used, or disclosed except in accordance with written authorization from Komatsu America International Company. It is our policy to improve our products whenever it is possible and practical to do so. We reserve the right to make changes or add improvements at any time without incurring any obligation to install such changes on products sold previously. Due to this continuous program of research and development, periodic revisions may be made to this publication. It is recommended that customers contact their distributor for information on the latest revision.
December 1999
Copyright Komatsu America International Company
CONTENTS
01
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 01-1
10
STRUCTURE AND FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
20
TESTING AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-1
30
DISASSEMBLY AND ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . 30-1
40
MAINTENANCE STANDARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-1
WA250-3PTC
LIST OF ORIGINAL, NEW AND REVISED PAGES The affected pages are indicated by using the following marks. It is requested that necessary actions be taken to these pages according to the table below.
Mark
Indicatioin
Action
O
New page to be added
Add
•
Page to be replaced
Replace
Page to be deleted
Discard
(
)
Pages without marks were previous additions or revised pages. LIST OF ORIGINAL, NEW AND REVISED PAGES Mark
Page
Rev
•
00-1 00-2 00-2-1 00-2-2 00-2-3 00-2-4 00-3 00-4 00-5 00-6 00-7 00-8 00-9 00-10 00-11 00-12 00-14 00-15 00-16 00-17 00-18 00-19 00-20
•
O O O O •
01-1 01-2 01-3 01-4 01-5 01-6 01-7 01-8 01-9 01-10 01-11 01-12 01-13 01-14 01-15 01-16
WA250-3PTC
• • • • •
Mark
Page
Rev
01-17 01-18 01-19 01-20
•
10-1 10-2 10-3 10-4 10-5 10-6 10-7 10-8 10-9 10-10 10-11 10-12 10-13 10-14 10-15 10-16 10-17 10-18 10-19 10-20 10-21 10-22 10-23 10-24 10-25 10-26 10-27 10-28 10-29 10-30 10-31 10-32 10-33 10-34 10-35
•
Mark
Page 10-36 10-37 10-38 10-39 10-40 10-41 10-42 10-43 10-44 10-45 10-46 10-47 10-48 10-49 10-50 10-51 10-52 10-53 10-54 10-55 10-56 10-57 10-58 10-59 10-60 10-61 10-62 10-63 10-64 10-65 10-66 10-67 10-68 10-69 10-70 10-71 10-72 10-73 10-74 10-75 10-76
Rev
Mark
Page
Rev
10-77 10-78 10-79 10-80 10-81 10-82 10-83 10-84 10-85 10-86 10-87 10-88 10-89 10-90 10-91 10-92 10-93 10-94 10-95 10-96 10-97 10-98 10-99 10-100 10-101 10-102 10-103 10-104 10-105 10-106 10-107 10-108 10-109 10-110 10-111 10-112 10-113 10-114 10-115 10-116 10-117
00-2-1 •
LIST OF ORIGINAL, NEW AND REVISED PAGES Mark
• • • • • • O O
00-2-2 •
Page 10-118 10-119 10-120 10-121 10-122 10-123 10-124 10-125 10-126 10-127 10-128 10-129 10-130 10-131 10-132 10-133 10-334 10-135 10-136 10-137 10-138 10-139 10-140 10-141 10-142 10-143 10-144 10-145 10-146 10-146-1 10-146-2 10-147 10-148 10-149 10-150 10-151 10-152 10-153 10-154 10-155 10-156 10-157 10-158 10-159 10-160 10-161 10-162 10-163 10-164
Rev
Mark • •
• • • • • • • •
Page 20-1 20-2 20-3 20-4 20-5 20-6 20-7 20-8 20-9 20-10 20-11 20-12 20-13 20-14 20-15 20-16 20-17 20-18 20-19 20-20 20-21 20-22 20-23 20-24 20-25 20-26 20-27 20-28 20-29 20-30 20-31 20-32 20-33 20-34 20-35 20-36 20-37 20-38 20-39 20-40 20-41 20-42 20-43 20-44 20-45 20-46 20-47 20-48 20-49 20-50
Rev
Mark
•
Page
Rev
20-51 20-52 20-53 20-54 O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O
20-101 20-102 20-103 20-104 20-105 20-106 20-107 20-108 20-109 20-110 20-111 20-112 20-113 20-114 20-115 20-116 20-117 20-118 20-119 20-120 20-121 20-122 20-123 20-124 20-125 20-126 20-127 20-128 20-129 20-130 20-131 20-132 20-133 20-134 20-135 20-136 20-137 20-138 20-139 20-140 20-141 20-142 20-143 20-144 20-145
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
Mark
Page
Rev
O O O
20-146 20-147 20-148
• • •
O O O O O O O O O O O O O O O O O O O O
20-151 20-152 20-153 20-154 20-155 20-156 20-157 20-158 20-159 20-160 20-161 20-162 20-163 20-164 20-165 20-166 20-167 20-168 20-169 20-170
• • • • • • • • • • • • • • • • • • • •
O O O O O O O O O O O O O O O O O O O O O O
20-201 20-202 20-203 20-204 20-205 20-206 20-207 20-208 20-209 20-210 20-211 20-212 20-213 20-214 20-215 20-216 20-217 20-218 20-219 20-220 20-221 20-222
• • • • • • • • • • • • • • • • • • • • • •
WA250-3PTC
LIST OF ORIGINAL, NEW AND REVISED PAGES Mark
Page
Rev
Mark
Page
Rev
Mark
O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O
20-251 20-252 20-253 20-254 20-255 20-256 20-257 20-258 20-259 20-260 20-261 20-262 20-263 20-264 20-265 20-266 20-267 20-268 20-269 20-270 20-271 20-272 20-273 20-274 20-275 20-276 20-277 20-278 20-279 20-280 20-281 20-282 20-283 20-284 20-285 20-286 20-287 20-288
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
O O O O O O O O O O O O O O O O O O
20-311 20-312 20-313 20-314 20-315 20-316 20-317 20-318 20-319 20-320 20-321 20-322 20-323 20-324 20-325 20-326 20-327 20-328
• • • • • • • • • • • • • • • • • •
O O O O O O O O O O O O O O O O O O O O
20-351 20-352 20-353 20-354 20-355 20-356 20-357 20-358 20-359 20-360 20-361 20-362 20-363 20-364 20-365 20-366 20-367 20-368 20-369 20-370
• • • • • • • • • • • • • • • • • • • •
O O O O O O O O O O
20-301 20-302 20-303 20-304 20-305 20-306 20-307 20-308 20-309 20-310
• • • • • • • • • •
O O O O O O
20-401 20-402 20-403 20-404 20-405 20-406
• • • • • •
O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O
WA250-3PTC
Page 30-1 30-2 30-3 30-4 30-5 30-6 30-7 30-8 30-9 30-10 30-11 30-12 30-13 30-14 30-15 30-16 30-17 30-18 30-19 30-20 30-21 30-22 30-23 30-24 30-25 30-26 30-27 30-28 30-29 30-30 30-31 30-32 30-33 30-34 30-35 30-36 30-37 30-38 30-39 30-40 30-41 30-42 30-43 30-44 30-45 30-46 30-47 30-48 30-49 30-50
Rev
Mark
Page
Rev
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O
30-51 30-52 30-53 30-54 30-55 30-56 30-57 30-58 30-59 30-60 30-61 30-62 30-63 30-64 30-65 30-66 30-67 30-68 30-69 30-70 30-71 30-72 30-73 30-74 30-75 30-76 30-77 30-78 30-79 30-80 30-81 30-82 30-83 30-84 30-85 30-86 30-87 30-88 30-89 30-90 30-91 30-92 30-93 30-94 30-95 30-96 30-97 30-98 30-99 30-100
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
00-2-3 •
LIST OF ORIGINAL, NEW AND REVISED PAGES ark
Page
Rev
Mark
Page
Rev
Mark
Page
Rev
O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O
30-101 30-102 30-103 30-104 30-105 30-106 30-107 30-108 30-109 30-110 30-111 30-112 30-113 30-114 30-115 30-116 30-117 30-118 30-119 30-120 30-121 30-122 30-123 30-124 30-125 30-126 30-127 30-128 30-129 30-130 30-131 30-132 30-133 30-334 30-135 30-136 30-137 30-138 30-139 30-140 30-141 30-142 30-143 30-144 30-145 30-146 30-147 30-148 30-149 30-150
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O
30-151 30-152 30-153 30-154 30-155 30-156 30-157 30-158 30-159 30-160 30-161 30-162 30-163 30-164 30-165 30-166 30-167 30-168 30-169 30-170 30-171 30-172 30-173 30-174 30-175 30-176 30-177 30-178 30-179 30-180 30-181 30-182 30-183 30-184 30-185 30-186 30-187 30-188 30-189 30-190 30-191 30-192 30-193 30-194 30-195 30-196 30-197 30-198 30-199 30-200
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
O O O O O O O O O
30-202 30-203 30-204 30-205 30-206 30-207 30-208 30-209 30-210
• • • • • • • • •
00-2-4 •
40-1 40-2 40-3 40-4 40-5 40-6 40-7 40-8 40-9 40-10 40-11 40-12 40-13 40-14 40-15 40-16 40-17 40-18 40-19 40-20 40-21 40-22 40-23 40-24 40-25 40-26 40-27 40-28 40-29 40-30 40-31 40-32 40-33 40-34 40-35 40-36 40-37 40-38 40-39
Mark
Page
Rev
40-40 40-41 40-42 40-43 40-44 40-45 40-46 40-47 40-48
•
• • • O O O O O O
FOLDOUTS 10-83 10-97 10-99 10-101 10-103 10-105 10-107 10-109 10-111 10-113 10-121 10-141 10-144 10-145 10-146-1 20-127 20-129 20-143 20-144 20-145
•
• • • • • • • • •
WA250-3PTC
This is the sample of the manual Click on the download link for complete manual
Download Link
PRODUCT PUBLICATIONS INFORMATION
VARIOUS PRODUCT PARTS & SERVICE PUBLICATIONS ARE AVAILABLE TO ALL KOMATSU CONSTRUCTION EQUIPMENT OWNERS, INCLUDING OPERATION & MAINTENANCE MANUALS, PARTS BOOKS AND SHOP MANUALS. SPECIAL PUBLICATIONS SUCH AS SERVICE TOOL, AIR CONDITIONING, AND TURBOCHARGER SHOP MANUALS ARE ALSO AVAILABLE AS WELL AS SELECTED OPERATION & MAINTENANCE AND SHOP MANUALS IN FOREIGN LANGUAGES. THE PUBLICATIONS LISTED BELOW ARE AVAILABLE FOR THIS PARTICULAR MACHINE(S). DESCRIPTION
FORM NUMBER
PARTS BOOK - PAPER: Engine and Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BEPB003400
PARTS BOOK - MICROFICHE: Engine and Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BEPM003400
OPERATION & MAINTENANCE MANUAL: Engine and Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CEAM002000
SHOP MANUAL: Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CEBM001801 CEBM010002
SAFETY MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WLT70-1
PARTS AND SERVICE PUBLICATIONS CAN ONLY BE ACQUIRED BY AUTHORIZED KOMATSU DISTRIBUTORS, USING THE KOMATSU AMERICA INTERNATIONAL COMPANY PARTS INFORMATION PROCESSING SYSTEM (PIPS). IF THE PIPS SYSTEM IS NOT AVAILABLE AT THE DISTRIBUTOR LOCATION, THEN THE FOLLOWING REQUISITION FOR TECHNICAL SERVICE PUBLICATIONS AND SERVICE FORMS CAN BE USED. FORM KDC91D IS SHOWN ON THE REVERSE SIDE OF THIS PAGE.
WA250-3PTC
00-3 •
REQUISITION FOR TECHNICAL SERVICE PUBLICATIONS AND SERVICE FORMS COMPLETE FORM AND RETURN TO
•
SHIP TO
•
DataKom Publishing Corporation 440 North Fairway Drive Vernon Hills, IL 60061-8112 U.S.A. Attn: Service Publications Fax No. (847) 970-4186 Tel No. (847) 970-5887
COMPANY NAME
PURCHASE ORDER NO.
ATTN.
ORDER DATE
STREET ADDRESS
TYPE or PRINT ONLY
•
CITY, STATE, ZIP CODE COUNTRY
PHONE NO.
FAX NO.
SHIPPING METHOD
DISTR/BRANCH CODE
IMPORTANT - TO ASSURE SHIPMENT OF THE CORRECT PUBLICATION(S), THE MODEL NUMBER AND MACHINE SERIAL NUMBER MUST BE SHOWN. PARTS BOOK QTY.
KDC91E 072199
00-4
PUBLICATION FORM NO.
P-Paper M-Microfiche
PUBLICATION DESCRIPTION
MODEL NUMBER
CURRENT PRICES WILL BE CHARGED
SERIAL NUMBER
SAFETY
SAFETY NOTICE
SAFETY SAFETY NOTICE
IMPORTANT SAFETY NOTICE Proper service and repair is extremely important for the safe operation of your machine. The service and repair techniques recommended and described in this manual are both effective and safe methods of operation. Some of these operations require the use of tools specially designed for the purpose. To prevent injury to workers, the symbols and are used to mark safety precautions in this manual. The cautions accompanying these symbols should always be followed carefully. If any dangerous situation arises or may possibly arise, first consider safety, and take the necessary actions to deal with the situation.
GENERAL PRECAUTIONS
clean and make sure that there is no dirt or oil on the floor. Smoke only in the areas provided for smoking. Never smoke while working.
Mistakes in operation are extremely dangerous. Read the OPERATION & MAINTENANCE MANUAL carefully BEFORE operating the machine.
PREPARATIONS FOR WORK
1. Before carrying out any greasing or repairs, read all the precautions given on the decals which are fixed to the machine.
7. Before adding oil or making repairs, park the machine on hard, level ground, and block the wheels or tracks to prevent the machine from moving.
2. When carrying out any operation, always wear safety shoes and helmet. Do not wear loose work clothes, or clothes with buttons missing.
8. Before starting work, lower blade, ripper, bucket or any other work equipment to the ground. If this is not possible, insert the safety pin or use blocks to prevent the work equipment from falling. In addition, be sure to lock all the control levers and hang warning signs on them.
Always wear safety glasses when hitting parts with a hammer. Always wear safety glasses when grinding parts with a grinder, etc. 3. If welding repairs are needed, always have a trained, experienced welder carry out the work. When carrying out welding work, always wear welding gloves, apron, glasses, cap and other clothes suited for welding work. 4. When carrying out any operation with two or more workers, always agree on the operating procedure before starting. Always inform your fellow workers before starting any step of the operation. Before starting work, hang UNDER REPAIR signs on the controls in the operator's compartment. 5. Keep all tools in good condition and learn the correct way to use them. 6. Decide a place in the repair workshop to keep tools and removed parts. Always keep the tools and parts in their correct places. Always keep the work area
9. When disassembling or assembling, support the machine with blocks, jacks or stands before starting work. 10. Remove all mud and oil from the steps or other places used to get on and off the machine. Always use the handrails, ladders or steps when getting on or off the machine. Never jump on or off the machine. If it is impossible to use the handrails, ladders or steps, use a stand to provide safe footing. PRECAUTIONS DURING WORK 11. When removing the oil filler cap, drain plug or hydraulic pressure measuring plugs, loosen them slowly to prevent the oil from spurting out. Before disconnecting or removing components of the oil, water or air circuits, first remove the pressure completely from the circuit. 12. The water and oil in the circuits are hot when the
00-5
SAFETY engine is stopped, so be careful not to get burned. Wait for the oil and water to cool before carrying out any work on the oil or water circuits. 13. Before starting work, remove the leads from the battery. ALWAYS remove the lead from the negative (-) terminal first. 14. When raising heavy components, use a hoist or crane. Check that the wire rope, chains and hooks are free from damage. Always use lifting equipment which has ample capacity. Install the lifting equipment at the correct places. Use a hoist or crane and operate slowly to prevent the component from hitting any other part. Do not work with any part still raised by the hoist or crane. 15. When removing covers which are under internal pressure or under pressure from a spring, always leave two bolts in position on opposite sides. Slowly release the pressure, then slowly loosen the bolts to remove. 16. When removing components, be careful not to break or damage the wiring, Damaged wiring may cause electrical fires. 17. When removing piping, stop the fuel or oil from spilling out. If any fuel or oil drips on to the floor, wipe it up immediately. Fuel or oil on the floor can cause you to slip, or can even start fires. 18. As a general rule, do not use gasoline to wash parts. In particular, use only the minimum of gasoline when
00-6
SAFETY NOTICE washing electrical parts. 19. Be sure to assemble all parts again in their original places. Replace any damaged part with new parts. When installing hoses and wires, be sure that they will not be damaged by contact with other parts when the machine is being operated. 20. When installing high pressure hoses, make sure that they are not twisted. Damaged tubes are dangerous, so be extremely careful when installing tubes for high pressure circuits. Also check that connecting parts are correctly installed. 21. When assembling or installing parts, always use the specified tightening torques. When installing protective parts such as guards, or parts which vibrate violently or rotate at high speed, be particularly careful to check that they are installed correctly. 22. When aligning two holes, never insert your fingers or hand. Be careful not to get your fingers caught in a hole. 23. When measuring hydraulic pressure, check that the measuring tool is correctly assembled before taking any measurements. 24. Take care when removing or installing the tracks of track-type machines. When removing the track, the track separates suddenly, so never let anyone stand at either end of the track.
FOREWARD
GENERAL
FOREWARD GENERAL This shop manual has been prepared as an aid to improve the quality of repairs by giving the serviceman an accurate understanding of the product and by showing him the correct way to perform repairs and make judgements. Make sure you understand the contents of this manual and use it to full effect at every opportunity.
This shop manual mainly contains the necessary technical information for operations performed in a service workshop. For ease of understanding, the manual is divided into the following sections. These sections are further divided into each main group of components. GENERAL This section lists the general machine dimensions, performance specifications, component weights, and fuel, coolant and lubricant specification charts. STRUCTURE AND FUNCTION This section explains the structure and function of each component. It serves not only to give an understanding of the structure, but also serves as reference material for troubleshooting. TESTING AND ADJUSTING This section explains checks to be made before and after performing repairs, as well as adjustments to be made at completion of the checks and repairs. Troubleshooting charts correlating "Problems" to "Causes" are also included in this section. DISASSEMBLY AND ASSEMBLY This section explains the order to be followed when removing, installing, disassembling or assembling each component, as well as precautions to be taken for these operations. MAINTENANCE STANDARD This section gives the judgement standards when inspecting disassembled parts.
NOTICE The specifications contained in this shop manual are subject to change at any time and without any advance notice. Contact your distributor for the latest information.
00-7
FOREWARD
HOW TO READ THE SHOP MANUAL
HOW TO READ THE SHOP MANUAL VOLUMES
REVISED EDITION MARK
Shop manuals are issued as a guide to carrying out repairs. They are divided as follows: Chassis volume: Issued for every machine model Engine volume: Issued for each engine series Electrical volume: Each issued as one to cover all models Attachment volume: Each issued as one to cover all models
When a manual is revised, an edition mark ( ....) is recorded on the bottom outside corner of the pages. REVISIONS Revised pages are shown at the LIST OF REVISED PAGES between the title page and SAFETY page. SYMBOLS
These various volumes are designed to avoid duplication of information. Therefore to deal with all repairs for any model, it is necessary that chassis, engine electrical and attachment be available. DISTRIBUTION AND UPDATING Any additions, amendments or other changes will be sent to your distributors. Get the most up-to-date information before you start any work. FILING METHOD 1. See the page number on the bottom of the page. File the pages in correct order. 2. Following examples show how to read the page number: Example 1 (Chassis volume): 10 - 3 Item number (10. Structure and Function) Consecutive page number for each item Example 2 (Engine volume): Refer to the pertinent engine manual. 3. Additional pages: Additional pages are indicated by a hyphen (-) and numbered after the page number. File as in the example. Example: 10-4 10-4-1 Added pages 10-4-2 10-5
00-8
So that the shop manual can be of ample practical use, important places for safety and quality are marked with the following symbols. Symbol
Item
Remarks
Safety
Special safety precautions are necessary when performing the work.
Caution
Special technical precautions or other precautions for preserving standards are necessary when performing the work.
Weight
Weight of parts or systems. Caution necessary when selecting hoisting wire or when working posture is important, etc.
Tightening torque
Places that require special attention for tightening torque during assembly.
Coat
Places to be coated with adhesives and lubricants etc.
Oil, water
Places where oil, water or fuel must be added, and the capacity.
Drain
Places where oil or water must be drained, and quantity to be drained.
FOREWARD
HOISTING INSTRUCTIONS
HOISTING INSTRUCTIONS HOISTING Heavy parts (25 kg or more) must be lifted with a hoist etc. In the DISASSEMBLY AND ASSEMBLY section, every part weighing 25 kg or more is indicated clearly with the symbol
If a part cannot be smoothly removed from the machine by hoisting, the following checks should be made: 1) Check for removal of all bolts fastening the part to the relative parts. 2) Check for existence of another part causing interface with the part to be removed. WIRE ROPES 1) Use adequate ropes depending on the weight of parts to be hoisted, referring to the table below: Wire ropes (Standard "Z" or "S" twist ropes without galvanizing Rope diameter (mm) 10.0 11.2 12.5 14.0 16.0 18.0 20.0 22.4 30.0 40.0 50.0 60.0
Allowable load (tons) 1.0 1.4 1.6 2.2 2.8 3.6 4.4 5.6 10.0 18.0 28.0 40.0
3) Do not sling a heavy load with one rope alone, but sling with two or more ropes symmetrically wound on to the load. Slinging with one rope may cause turning of the load during hoisting, untwisting of the rope, or slipping of the rope from its original winding position on the load, which can result in a dangerous accident. 4) Do not sling a heavy load with ropes forming a wide hanging angle from the hook. When hoisting a load with two or more ropes, the force subjected to each rope will increase with the hanging angles. The table below shows the variation of allowable load (kg) when hoisting is made with two ropes, each of which is allowed to sling up to 1000 kg vertically, at various hanging angles. When two ropes sling a load vertically, up to 2000 kg of total weight can be suspended. This weight becomes 1000 kg when two ropes make a 120 hanging angle. On the other hand, two ropes are subject to an excessive force as large as 4000 kg if they sling a 2000 kg load at a lifting angle of 150 .
The allowable load value is estimated to be 1/6 or 1/7 of the breaking strength of the rope used. 2) Sling wire ropes from the middle portion of the hook. Slinging near the edge of the hook may cause the rope to slip off the hook during hoisting, and a serious accident can result. Hooks have maximum strength at the middle portion.
00-9
FOREWARD
COATING MATERIALS
COATING MATERIALS The recommended coating materials prescribed in the shop manuals are listed below. Category
Code
Part No.
Qty
Container
Main applications,features
LT-1A
790-129-9030
150 g
Tube
Used to prevent rubber gaskets, rubber cushions and cork plugs from coming out
LT-1B
790-129-9050
20 g (x2)
Plastic container
Used in places requiring an immediately effective, strong adhesive. Used for plastics (except polyethylene, polypropylene, tetrafluoroethylene, and vinyl chloride), rubber, metal and non-metal.
LT-2
09940-00030
50 g
Plastic container
Features: Resistance to heat, chemicals Used for anti-loosening and sealant purposes for bolts and plugs.
LT-3
790-129-9060 Set of adhesive and hardening agent
Adh 1 kg Hard agt 500 kg
Can
LT-4
790-129-9040
250 g
Plastic container
Loctite 648-50
79A-129-9110
50 cc
---
Features: Resistance to heat, chemicals Used at joint portions subject to high temperature.
LG-1
790-129-9010
200 g
Tube
Used as adhesive or sealant for gaskets and packing of power train case, etc.
Can
Features: Resistance to heat Used as sealant for flange surfaces and bolts at high temperature locations; used to prevent seizure. Used as sealant for heat resistant gasket for at high temperature locations such as engine pre-combustion chamber, exhaust pipe.
Adhesive
LG-3
790-129-9070
1 kg
Used as adhesive or sealant for metal, glass or plastic. Used as sealant for machined holes.
LG-4
790-129-9020
200 g
Tube
Features: Resistance towater, oil Used as sealant for flange surface, thread. Also possible to use as sealant for flanges with large clearance. Used as sealant for mating surfaces of final drive case, transmission case.
LG-5
790-129-9080
1 kg
Plastic container
Used as sealant for various threads, pipe joints, flanges. Used as sealant for tapered plugs, elbows, nipples of hydraulic piping.
LG-6
09940-00011
250 g
Tube
Features: Silicon based, resistant to heat, cold. Used as sealant for flange surface, thread. Used as sealant for oil pan, final drive case, etc.
LG-7
09920-00150
150 g
Tube
Features: Silicon based, quick hardening type. Used as sealant for flywheel housing, intake manifold, oil pan, thermostat housing, etc.
Rust preven-tion lubricant
---
09940-00051
60 g
Can
Used as lubricant for sliding parts (to prevent squeaking).
Molybdenum disulfide lubricant
---
09940-00040
200 g
Tube
Used to prevent seizure or scuffing of the thread when press fitting or shrink fitting. Used as lubricant for linkage, bearings, etc.
G2-L1
SYG-350Ll SYG-400Ll SYG-400Ll-A SYG-160Ll SYGA-160CNLl
Various
Various
General purpose type
Calcium grease
G2-CA
SSG2-400CA SYG2-350CA SYG2-400CA-A SYG2-160CA SYGA-16CNCA
Various
Various
Used for normal temperature, light load bearing at places in contact with water or steam.
Molybdenum disulfide grease
---
SYG2-400M
400 g (10/case)
Bellows type
Gasket sealant
Lithium grease
00-10
Used for places with heavy load.
FOREWARD
STANDARD TORQUE REQUIREMENTS
STANDARD TORQUE REQUIREMENTS STANDARD TORQUE REQUIREMENTS OF BOLTS AND NUTS The following charts give the standard torques values of bolts and nuts. Exceptions are given in sections of DISASSEMBLY AND ASSEMBLY. 1 kgm = 9.806 Nm Thread diameter of bolt
Width across flat
mm
mm
kgm
Nm
6
10
1.35 ±0.15
13.2 ±1.4
8
13
3.20 ±0.3
31.4 ±2.9
10
17
6.70 ±0.7
65.7 ±6.8
12
19
11.5 ±1.0
112 ±9.8
14
22
18 ±2.0
177 ±19
16
24
28.5 ±3
279 ±29
18
27
39 ±4
383 ±39
20
30
56 ±6
549 ±58
22
32
76 ±8
745 ±78
24
36
94.5 ±10
927 ±98
27
41
135 ±15
1320 ±140
30
46
175 ±20
1720 ±190
33
50
225 ±25
2210 ±240
36
55
280 ±30
2750 ±290
39
60
335 ±35
3280 ±340
This torque table does not apply to the bolts with which nylon packing or other non-ferrous metal washers are to be used, or which require torquing to otherwise specified values.
00-11
This is the sample of the manual Click on the download link for complete manual
Download Link