CEBM013003
WHEEL LOADER
SERIAL NUMBERS
and UP
This material is proprietary to Komatsu America Corp. and is not to be reproduced, used, or disclosed except in accordance with written authorization from Komatsu America Corp. It is our policy to improve our products whenever it is possible and practical to do so. We reserve the right to make changes or add improvements at any time without incurring any obligation to install such changes on products sold previously. Due to this continuous program of research and development, periodic revisions may be made to this publication. It is recommended that customers contact their distributor for information on the latest revision.
October 2007 Printed in USA
Copyright 2007 Komatsu DataKom Publishing Corporation 00-1
FOREWORD 12
CONTENTS
CONTENTS
00
01
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 01-1
10
STRUCTURE AND FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
20
TESTING, ADJUSTING AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-1
30
DISASSEMBLY AND ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-1
90
OTHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90-1
00-2
WA200-
FOREWORD The affected pages are indicated by using the following marks. It is requested that necessary actions be taken to these pages according to the table below.
Mark
( ) Mark
Page
Rev
Mark
Page
Rev
Mark
Indication
Action
New page to be added
Add
Page to be replaced
Replace
Page to be deleted
Discard
Page
Rev
Mark
Page
00-1
00-22
10-15
10-44
00-2
00-23
10-16
10-45
00-2-1
00-24
10-17
10-46
10-18
10-47
00-2-2 00-2-3
01-1
10-19
10-48
00-2-4
01-2
10-20
10-49
00-2-5
01-3
10-21
10-50
00-2-6
01-4
10-22
10-51
00-2-7
01-5
10-23
10-52
00-2-8
01-6
10-24
10-53
00-3
01-7
10-25
10-54
00-4
01-8
10-26
10-55
00-5
01-9
10-27
10-56
00-6
01-10
10-28
10-57
10-29
10-58
00-7 00-8
10-1
10-30
10-59
00-9
10-2
10-31
10-60
00-10
10-3
10-32
10-61
00-11
10-4
10-33
10-62
00-12
10-5
10-34
10-63
00-13
10-6
10-35
10-64
00-14
10-7
10-36
10-65
00-15
10-8
10-37
10-66
00-16
10-9
10-38
10-67
00-17
10-10
10-39
10-68
00-18
10-11
10-40
10-69
00-19
10-12
10-41
10-70
00-20
10-13
10-42
10-71
00-21
10-14
10-43
10-72
WA200-5L,WA200PT-5L
WA200-5L,WA200PT-5L
Rev
00-2-1
FOREWORD Mark
00-2-2
Page
Rev
Mark
Page
Rev
Mark
Page
Rev
Mark
Page
10-73
10-106
10-139
10-172
10-74
10-107
10-140
10-173
10-75
10-108
10-141
10-174
10-76
10-109
10-142
10-175
10-77
10-110
10-143
10-176
10-78
10-111
10-144
10-177
10-79
10-112
10-145
10-178
10-80
10-113
10-146
10-179
10-81
10-114
10-147
10-180
10-82
10-115
10-148
10-181
10-83
10-116
10-149
10-182
10-84
10-117
10-150
10-183
10-85
10-118
10-151
10-184
10-86
10-119
10-152
10-185
10-87
10-120
10-153
10-186
10-88
10-121
10-154
10-187
10-89
10-122
10-155
10-188
10-90
10-123
10-156
10-189
10-91
10-124
10-157
10-190
10-92
10-125
10-158
10-191
10-93
10-126
10-159
10-192
10-94
10-127
10-160
10-193
10-95
10-128
10-161
10-194
10-96
10-129
10-162
10-195
10-97
10-130
10-163
10-196
10-98
10-131
10-164
10-197
10-99
10-132
10-165
10-198
10-100
10-133
10-166
10-199
10-101
10-134
10-167
10-200
10-102
10-135
10-168
10-201
10-103
10-136
10-169
10-202
10-104
10-137
10-170
10-203
10-105
10-138
10-171
10-204
Rev
WA200-5L,WA200PT-5L
FOREWORD Mark
Page
Rev
10-205
Mark
Page 10-238
10-206
Rev
Mark
Page
Rev
Mark
Page
20-32
20-65
20-33
20-66
10-207
20-1
20-34
20-67
10-208
20-2
20-35
20-68
10-209
20-3
20-36
20-69
10-210
20-4
20-37
20-70
10-211
20-5
20-38
20-71
10-212
20-6
20-39
20-72
10-213
20-7
20-40
20-73
10-214
20-8
20-41
20-74
10-215
20-9
20-42
20-75
10-216
20-10
20-43
20-76
10-217
20-11
20-44
20-77
10-218
20-12
20-45
20-78
10-219
20-13
20-46
10-220
20-14
20-47
20-101
10-221
20-15
20-48
20-102
10-222
20-16
20-49
20-103
10-223
20-17
20-50
20-104
10-224
20-18
20-51
20-105
10-225
20-19
20-52
20-106
10-226
20-20
20-53
20-107
10-227
20-21
20-54
20-108
10-228
20-22
20-55
20-109
10-229
20-23
20-56
20-110
10-230
20-24
20-57
20-111
10-231
20-25
20-58
20-112
10-232
20-26
20-59
20-113
10-233
20-27
20-60
20-114
10-234
20-28
20-61
20-115
10-235
20-29
20-62
20-116
10-236
20-30
20-63
20-117
10-237
20-31
20-64
20-118
WA200-5L,WA200PT-5L
Rev
00-2-3
FOREWORD Mark
Page
Rev
Mark
Page
Mark
Page
Rev
Mark
Page
20-119
20-152
20-228
20-322
20-120
20-153
20-229
20-323
20-121
20-154
20-230
20-324
20-122
20-155
20-231
20-325
20-123
20-156
20-232
20-326
20-233
20-327
20-124
00-2-4
Rev
20-125
20-201
20-234
20-328
20-126
20-202
20-235
20-329
20-127
20-203
20-236
20-330
20-128
20-204
20-237
20-331
20-129
20-205
20-238
20-332
20-130
20-206
20-131
20-207
20-301
20-334
20-132
20-208
20-302
20-335
20-133
20-209
20-303
20-336
20-134
20-210
20-304
20-337
20-135
20-211
20-305
20-338
20-136
20-212
20-306
20-339
20-137
20-213
20-307
20-340
20-138
20-214
20-308
20-341
20-139
20-215
20-309
20-342
20-140
20-216
20-310
20-343
20-141
20-217
20-311
20-344
20-142
20-218
20-312
20-345
20-143
20-219
20-313
20-346
20-144
20-220
20-314
20-347
20-145
20-221
20-315
20-348
20-146
20-222
20-316
20-349
20-147
20-223
20-317
20-350
20-148
20-224
20-318
20-351
20-149
20-225
20-319
20-352
20-150
20-226
20-320
20-353
20-151
20-227
20-321
20-354
Rev
20-333
WA200-5L,WA200PT-5L
This is the sample of the manual Click on the download link for complete manual
Download Link
FOREWORD Mark
Page
Rev
Mark
Page
Rev
Mark
Page
Rev
Mark
Page
20-355
20-388
20-422
20-455
20-356
20-389
20-423
20-456
20-357
20-390
20-424
20-457
20-358
20-391
20-425
20-458
20-359
20-392
20-426
20-459
20-360
20-393
20-427
20-460
20-361
20-394
20-428
20-461
20-362
20-395
20-429
20-462
20-363
20-396
20-430
20-463
20-364
20-397
20-431
20-464
20-365
20-398
20-432
20-465
20-433
20-466
20-366 20-367
20-401
20-434
20-467
20-368
20-402
20-435
20-468
20-369
20-403
20-436
20-469
20-370
20-404
20-437
20-470
20-371
20-405
20-438
20-471
20-372
20-406
20-439
20-472
20-373
20-407
20-440
20-473
20-374
20-408
20-441
20-474
20-375
20-409
20-442
20-475
20-376
20-410
20-443
20-476
20-377
20-411
20-444
20-378
20-412
20-445
20-501
20-379
20-413
20-446
20-502
20-380
20-414
20-447
20-503
20-381
20-415
20-448
20-504
20-382
20-416
20-449
20-505
20-383
20-417
20-450
20-506
20-384
20-418
20-451
20-507
20-385
20-419
20-452
20-508
20-386
20-420
20-453
20-509
20-387
20-421
20-454
20-510
WA200-5L,WA200PT-5L
Rev
00-2-5
FOREWORD Mark
Page
Rev
Mark
Page
Mark
Page
Rev
Mark
Page
20-511
20-617
30-25
30-58
20-512
20-618
30-26
30-59
20-513
20-619
30-27
30-60
20-514
20-620
30-28
30-61
20-515
20-621
30-29
30-62
20-516
20-622
30-30
30-63
20-517
20-623
30-31
30-64
20-518
20-624
30-32
30-65
30-33
30-66
20-519
00-2-6
Rev
20-520
30-1
30-34
30-67
20-521
30-2
30-35
30-68
20-522
30-3
30-36
30-69
20-523
30-4
30-37
30-70
20-524
30-5
30-38
30-71
20-525
30-6
30-39
30-72
20-526
30-7
30-40
30-73
30-8
30-41
30-74
20-601
30-9
30-42
30-75
20-602
30-10
30-43
30-76
20-603
30-11
30-44
30-77
20-604
30-12
30-45
30-78
20-605
30-13
30-46
30-79
20-606
30-14
30-47
30-80
20-607
30-15
30-48
30-81
20-608
30-16
30-49
30-82
20-609
30-17
30-50
30-83
20-610
30-18
30-51
30-84
20-611
30-19
30-52
30-85
20-612
30-20
30-53
30-86
20-613
30-21
30-54
30-87
20-614
30-22
30-55
30-88
20-615
30-23
30-56
30-89
20-616
30-24
30-57
30-90
Rev
WA200-5L,WA200PT-5L
FOREWORD Mark
Page
Rev
Mark
Page
Rev
Mark
Page
Rev
Mark
Page
30-91
30-124
30-157
30-190
30-92
30-125
30-158
30-191
30-93
30-126
30-159
30-192
30-94
30-127
30-160
30-193
30-95
30-128
30-161
30-194
30-96
30-129
30-162
30-195
30-97
30-130
30-163
30-196
30-98
30-131
30-164
30-197
30-99
30-132
30-165
30-198
30-100
30-133
30-166
30-199
30-101
30-134
30-167
30-200
30-102
30-135
30-168
30-201
30-103
30-136
30-169
30-202
30-104
30-137
30-170
30-203
30-105
30-138
30-171
30-204
30-106
30-139
30-172
30-205
30-107
30-140
30-173
30-206
30-108
30-141
30-174
30-207
30-109
30-142
30-175
30-208
30-110
30-143
30-176
30-209
30-111
30-144
30-177
30-210
30-112
30-145
30-178
30-211
30-113
30-146
30-179
30-212
30-114
30-147
30-180
30-213
30-115
30-148
30-181
30-214
30-116
30-149
30-182
30-215
30-117
30-150
30-183
30-216
30-118
30-151
30-184
30-217
30-119
30-152
30-185
30-218
30-120
30-153
30-186
30-219
30-121
30-154
30-187
30-220
30-122
30-155
30-188
30-221
30-123
30-156
30-189
30-222
WA200-5L,WA200PT-5L
Rev
00-2-7
FOREWORD Mark
Page
Rev
Mark
Page
Mark
Page
30-223
30-256
90-6
30-224
30-257
90-7
30-225
30-258
90-8
30-226
30-259
90-9
30-227
30-260
90-10
30-228
30-261
90-11
30-229
30-262
90-12
30-230
30-263
90-13
30-231
30-264
90-14
30-232
30-265
90-15
30-233
30-266
90-16
30-234
(
)
30-267
90-17
30-235
(
)
30-268
90-18
30-236
(
)
30-269
90-19
30-237
(
)
30-270
90-20
30-238
(
)
30-271
90-21
30-239
(
)
30-272
90-22
30-240
(
)
30-273
90-23
30-241
(
)
30-274
90-24
30-242
(
)
30-275
90-25
30-243
(
)
30-276
90-26
30-244
(
)
30-277
90-27
30-245
(
)
30-278
90-28
30-246
(
)
30-279
90-29
30-247
(
)
30-280
90-30
30-248
(
)
30-281
90-31
30-249
(
)
30-282
90-32
30-250
00-2-8
Rev
Rev
Mark
Page
Rev
90-33
30-251
90-1
30-252
90-2
30-253
90-3
30-254
90-4
30-255
90-5
90-34
WA200-5L,WA200PT-5L
FOREWORD
SAFETY
12 SAFETY
SAFETY NOTICE
00
00
IMPORTANT SAFETY NOTICE
00
Proper service and repair is extremely important for the safe operation of your machine. The service and repair techniques recommended and described in this manual are both effective and safe methods of operation. Some of these operations require the use of tools specially designed for the purpose. To prevent injury to workers, the symbol is used to mark safety precautions in this manual. The cautions accompanying the symbols should always be followed carefully. If any dangerous situation arises or may possibly arise, first consider safety, and take the necessary actions to deal with the situation.
GENERAL PRECAUTIONS
00
PREPARATIONS FOR WORK
00
Mistakes in operation are extremely dangerous. Read the OPERATION & MAINTENANCE MANUAL carefully BEFORE operating the machine.
1.
Before adding oil or making repairs, park the machine on hard, level ground, and block the wheels or tracks to prevent the machine from moving.
1.
Before carrying out any greasing or repairs, read all the precautions given on the decals which are fixed to the machine.
2.
2.
When carrying out any operation, always wear safety shoes and helmet. Do not wear loose work clothes, or clothes with buttons missing. • Always wear safety glasses when hitting parts with a hammer. • Always wear safety glasses when grinding parts with a grinder, etc.
Before starting work, lower blade, ripper, bucket or any other work equipment to the ground. If this is not possible, insert the safety pin or use blocks to prevent the work equipment from falling. In addition, be sure to lock all the control levers and hang warning signs on them.
3.
When disassembling or assembling, support the machine with blocks, jacks or stands before starting work.
4.
Remove all mud and oil from the steps or other places used to get on and off the machine. Always use the handrails, ladders or steps when getting on or off the machine. Never jump on or off the machine. If it is impossible to use the handrails, ladders or steps, use a stand to provide safe footing.
3.
If welding repairs are needed, always have a trained, experienced welder carry out the work. When carrying out welding work, always wear welding gloves, apron, glasses, cap and other clothes suited for welding work.
4.
When carrying out any operation with two or more workers, always agree on the operating procedure before starting. Always inform your fellow workers before starting any step of the operation. Before starting work, hang UNDER REPAIR signs on the controls in the operator's compartment.
5.
Keep all tools in good condition and learn the correct way to use them.
6.
Decide a place in the repair workshop to keep tools and removed parts. Always keep the tools and parts in their correct places. Always keep the work area clean and make sure that there is no dirt or oil on the floor. Smoke only in the areas provided for smoking. Never smoke while working.
WA200-5L, WA200PT-5L
PRECAUTIONS DURING WORK
00
1.
When removing the oil filler cap, drain plug or hydraulic pressure measuring plugs, loosen them slowly to prevent the oil from spurting out. Before disconnecting or removing components of the oil, water or air circuits, first remove the pressure completely from the circuit.
2.
The water and oil in the circuits are hot when the engine is stopped, so be careful not to get burned. Wait for the oil and water to cool before carrying out any work on the oil or water circuits.
3.
Before starting work, remove the leads from the battery. ALWAYS remove the lead from the negative (-) terminal first.
00-3
FOREWORD
SAFETY
12 4. When raising heavy components, use a hoist or crane. Check that the wire rope, chains and hooks are free from damage. Always use lifting equipment which has ample capacity. Install the lifting equipment at the correct places. Use a hoist or crane and operate slowly to prevent the component from hitting any other part. Do not work with any part still raised by the hoist or crane. 5.
When removing covers which are under internal pressure or under pressure from a spring, always leave two bolts in position on opposite sides. Slowly release the pressure, then slowly loosen the bolts to remove.
6.
When removing components, be careful not to break or damage the wiring, Damaged wiring may cause electrical fires.
7.
When removing piping, stop the fuel or oil from spilling out. If any fuel or oil drips on to the floor, wipe it up immediately. Fuel or oil on the floor can cause you to slip, or can even start fires.
8.
Never use flammable liquids to clean parts, always use approved non-flammable solvents to clean parts.
9.
Be sure to assemble all parts in their original locations. Replace any damaged part with new parts. • When installing hoses and wires, be sure that they will not be damaged by contact with other parts when the machine is being operated.
10. When installing high pressure hoses, be sure that they are not twisted. Damaged tubbing dangerous, be extremely careful when installing tubes for high pressure circuits. Also make sure parts are correctly installed. 11. When assembling or installing parts, always use the specified tightening torques and sequences. When installing protective parts such as guards, or parts that may vibrate or rotate at high speeds, be particularly careful to check their installation carefully. 12. When aligning two holes, never insert your fingers or hand. Use appropriate tools to align parts. 13. When measuring hydraulic pressure, be sure the measuring tool is correctly assembled before taking any measurements. 14. Take care when removing or installing the tracks on track-type machines. When removing the track, the track separates suddenly, never let anyone stand at either end of the track. 15. When making repairs or adjustments on electronically controlled engines, avoid any physical contact with the injection systems wiring harness while the engine is running. Due to the high voltage and amperage in this system, serious injury may occur. 16. When removing the track, the track separates suddenly, so never let anyone stand at either end of the track.
00-4
WA200-5L, WA200PT-5L
FOREWORD
GENERAL
12 GENERAL This shop manual has been prepared as an aid to improve the quality of repairs by giving the serviceman an accurate understanding of the product and by showing him the correct way to perform repairs and make judgements. Make sure you understand the contents of this manual and use it to full effect at every opportunity.
00
This section explains checks to be made before and after performing repairs, as well as adjustments to be made at completion of the checks and repairs. Troubleshooting charts correlating “Problems” to “Causes” are also included in this section. DISASSEMBLY AND ASSEMBLY
This shop manual mainly contains the necessary technical information for operations performed in a service workshop. For ease of understanding, the manual is divided into the following sections. These sections are further divided into each main group of components. GENERAL
This section explains the order to be followed when removing, installing, disassembling or assembling each component, as well as precautions to be taken for these operations. MAINTENANCE STANDARD This section gives the judgement standards when inspecting disassembled parts.
This section lists the general machine dimensions, performance specifications, component weights, and fuel, coolant and lubricant specification charts. STRUCTURE AND FUNCTION This section explains the structure and function of each component. It serves not only to give an understanding of the structure, but also serves as reference material for troubleshooting. TESTING, ADJUSTING AND TROUBLESHOOTING NOTICE The specifications contained in this shop manual are subject to change at any time and without any advance notice. Contact your distributor for the latest information.
00-5
WA200-5L, WA200PT-5L
FOREWORD
HOW TO READ THE SHOP MANUAL
12 HOW TO READ THE SHOP MANUAL
VOLUMES
00
Shop manuals are issued as a guide to carrying out repairs. They are divided as follows: Chassis volume: Engine volume:
Symbol
Electrical volume: Each issued as one to cover all models Attachment volume: Each issued as one to cover all models These various volumes are designed to avoid duplication of information. Therefore to deal with all repairs for any model, it is necessary that chassis, engine, electrical and attachment be available.
1. 2.
00
Item
Remarks
Safety
Special safety precautions are necessary when performing the work.
Caution
Special technical precautions or other precautions for preserving standards are necessary when performing the work.
Weight
Weight of parts or systems. Caution necessary when selecting hoisting wire or when working posture is important, etc.
Tightening torque
Places that require special attention for tightening torque during assembly.
Coat
Places to be coated with adhesives and lubricants etc.
Oil, water
Places where oil, water or fuel must be added, and the capacity.
Drain
Places where oil or water must be drained, and quantity to be drained.
00
Any additions, amendments or other changes will be sent to your distributors. Get the most up-to-date information before you start any work.
FILING METHOD
SYMBOLS So that the shop manual can be of ample practical use, important places for safety and quality are marked with the following symbols.
Issued for every machine model Issued for each engine series
DISTRIBUTION AND UPDATING
00
00
See the page number on the bottom of the page. File the pages in correct order. Following examples show how to read the page number: Example: 10 - 3 Item number (10. Structure and Function) Consecutive page number for each item
3.
Additional pages: Additional pages are indicated by a hyphen (-) and numbered after the page number. File as in the example. Example:
10-4 10-4-1 10-4-2
Added pages
10-5
REVISED EDITION MARK
00
When a manual is revised, an edition mark ( …) is recorded on the bottom outside corner of the pages.
REVISIONS
00
Revised pages are shown at the LIST OF REVISED PAGES between the title page and SAFETY page.
00-6
WA200-5L, WA200PT-5L
FOREWORD
HOISTING INSTRUCTIONS
12 HOISTING INSTRUCTIONS
00
HOISTING
00
WARNING! Heavy parts (25 kg or more) must be lifted with a hoist etc. In the DISASSEMBLY AND ASSEMBLY section, every part weighing 25 kg or more is indicated clearly with the symbol.
1. 2.
If a part cannot be smoothly removed from the machine by hoisting, the following checks should be made: Check for removal of all bolts fastening the part to the relative parts. Check for existence of another part causing interface with the part to be removed.
WIRE ROPES 1.
Use adequate ropes depending on the weight of parts to be hoisted, referring to the table below:
Rope diameter
Allowable load
mm
kN
tons
10
9.8
1.0
11.2
13.7
1.4
12.5
15.7
1.6
14
21.6
2.2
16
27.5
2.8
18
35.3
3.6
20
43.1
4.4
22.4
54.9
5.6
30
98.1
10.0
40
176.5
18.0
50
274.6
28.0
60
392.2
40.0
Do not sling a heavy load with one rope alone, but sling with two or more ropes symmetrically wound on to the load. WARNING! Slinging with one rope may cause turning of the load during hoisting, untwisting of the rope, or slipping of the rope from its original winding position on the load. This can result in a dangerous accident.
00
Wire ropes (Standard “Z” or “S” twist ropes without galvanizing)
2.
3.
4.
Do not sling a heavy load with ropes forming a wide hanging angle from the hook. When hoisting a load with two or more ropes, the force subjected to each rope will increase with the hanging angles. The table below shows the variation of allowable load (kg) when hoisting is made with two ropes, each of which is allowed to sling up to 1000 kg vertically, at various hanging angles. When two ropes sling a load vertically, up to 2000 kg of total weight can be suspended. This weight becomes 1000 kg when two ropes make a 120° hanging angle. On the other hand, two ropes are subject to an excessive force as large as 4000 kg if they sling a 2000 kg load at a lifting angle of 150°.
The allowable load value is estimated to be 1/6 or 1/ 7 of the breaking strength of the rope used. Sling wire ropes from the middle portion of the hook. Slinging near the edge of the hook may cause the rope to slip off the hook during hoisting, and a serious accident can result. Hooks have maximum strength at the middle portion.
WA200-5L, WA200PT-5L
00-7
This is the sample of the manual Click on the download link for complete manual
Download Link