CEBM005806
HYDRAULIC EXCAVATOR SERIAL NUMBERS
and UP
This material is proprietary to Komatsu America Corp. and is not to be reproduced, used, or disclosed except in accordance with written authorization from Komatsu America Corp. It is our policy to improve our products whenever it is possible and practical to do so. We reserve the right to make changes or add improvements at any time without incurring any obligation to install such changes on products sold previously. Due to this continuous program of research and development, periodic revisions may be made to this publication. It is recommended that customers contact their distributor for information on the latest revision.
August 2008 Printed in USA
Copyright 2008 Komatsu DataKom Publications Division 00-1
FOREWORD 12
CONTENTS
CONTENTS
00
01
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 01-1
10
STRUCTURE AND FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
20
TESTING, ADJUSTING AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-1
30
DISASSEMBLY AND ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-1
90
OTHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90-1
00-2
PC200/220LC-7L
FOREWORD The affected pages are indicated by using the following marks. It is requested that necessary actions be taken to these pages according to the table below.
Mark
Indication
Action
New page to be added
Add
Page to be replaced
Replace
Page to be deleted
Discard
( ) Mark
Page
Rev
00-1
Mark
Page
Rev
00-22
00-2
Mark
Page
Rev
Mark
Page
10-19
10-48
10-20
10-49
00-2-1
01-1
10-21
10-50
00-2-2
01-2
10-22
10-51
00-2-3
01-3
10-23
10-52
00-2-4
01-4
10-24
10-53
00-2-5
01-5
10-25
10-54
00-2-6
01-6
10-26
10-55
00-2-7
01-7
10-27
10-56
00-2-8
01-8
10-28
10-57
10-29
10-58
00-3 00-4
10-1
10-30
10-59
00-5
10-2
10-31
10-60
00-6
10-3
10-32
10-61
00-7
10-4
10-33
10-62
00-8
10-5
10-34
10-63
00-9
10-6
10-35
10-64
00-10
10-7
10-36
10-65
00-11
10-8
10-37
10-66
00-12
10-9
10-38
10-67
00-13
10-10
10-39
10-68
00-14
10-11
10-40
10-69
00-15
10-12
10-41
10-70
00-16
10-13
10-42
10-71
00-17
10-14
10-43
10-72
00-18
10-15
10-44
10-73
00-19
10-16
10-45
10-74
00-20
10-17
10-46
10-75
00-21
10-18
10-47
10-76
PC200/220LC-7L
PC200/220LC-7L
Rev
00-2-1
FOREWORD Mark
00-2-2
Page
Rev
Mark
Page
Rev
Mark
Page
Rev
Mark
Page
10-77
10-110
10-143
10-176
10-78
10-111
10-144
10-177
10-79
10-112
10-145
10-178
10-80
10-113
10-146
10-179
10-81
10-114
10-147
10-180
10-82
10-115
10-148
10-181
10-83
10-116
10-149
10-182
10-84
10-117
10-150
10-183
10-85
10-118
10-151
10-184
10-86
10-119
10-152
10-185
10-87
10-120
10-153
10-186
10-88
10-121
10-154
10-187
10-89
10-122
10-155
10-188
10-90
10-123
10-156
10-189
10-91
10-124
10-157
10-190
10-92
10-125
10-158
10-191
10-93
10-126
10-159
10-192
10-94
10-127
10-160
10-193
10-95
10-128
10-161
10-194
10-96
10-129
10-162
10-195
10-97
10-130
10-163
10-196
10-98
10-131
10-164
10-197
10-99
10-132
10-165
10-198
10-100
10-133
10-166
10-199
10-101
10-134
10-167
10-200
10-102
10-135
10-168
10-201
10-103
10-136
10-169
10-202
10-104
10-137
10-170
10-203
10-105
10-138
10-171
10-204
10-106
10-139
10-172
10-205
10-107
10-140
10-173
10-206
10-108
10-141
10-174
10-207
10-109
10-142
10-175
10-208
Rev
PC200/220LC-7L
FOREWORD Mark
Page
Rev
Mark
Page
Rev
Mark
Page
Rev
Mark
Page
10-209
20-116
20-149
20-207
10-210
20-117
20-150
20-208
10-211
20-118
20-151
20-209
10-212
20-119
20-152
20-210
20-120
20-153
20-211
20-1
20-121
20-154
20-212
20-2
20-122
20-155
20-213
20-3
20-123
20-156
20-214
20-4
20-124
20-157
20-215
20-5
20-125
20-158
20-216
20-6
20-126
20-159
20-217
20-7
20-127
20-160
20-218
20-8
20-128
20-161
20-219
20-9
20-129
20-162
20-220
20-10
20-130
20-163
20-221
20-11
20-131
20-164
20-222
20-12
20-132
20-165
20-223
20-133
20-166
20-224
20-101
20-134
20-167
20-225
20-102
20-135
20-168
20-226
20-103
20-136
20-169
20-227
20-104
20-137
20-170
20-228
20-105
20-138
20-171
20-229
20-106
20-139
20-172
20-230
20-107
20-140
20-173
20-231
20-108
20-141
20-174
20-232
20-109
20-142
20-110
20-143
20-201
20-234
20-111
20-144
20-202
20-235
20-112
20-145
20-203
20-236
20-113
20-146
20-204
20-237
20-114
20-147
20-205
20-238
20-115
20-148
20-206
20-239
PC200/220LC-7L
Rev
20-233
00-2-3
FOREWORD Mark
Page
Rev
Mark
Page
Mark
Page
Rev
Mark
Page
20-240
20-273
20-321
20-354
20-241
20-274
20-322
20-355
20-242
20-275
20-323
20-356
20-243
20-276
20-324
20-357
20-244
20-277
20-325
20-358
20-245
20-278
20-326
20-359
20-246
20-279
20-327
20-360
20-247
20-280
20-328
20-361
20-248
20-281
20-329
20-362
20-249
20-282
20-330
20-363
20-250
20-283
20-331
20-364
20-251
20-284
20-332
20-365
20-333
20-366
20-252
00-2-4
Rev
20-253
20-301
20-334
20-367
20-254
20-302
20-335
20-368
20-255
20-303
20-336
20-369
20-256
20-304
20-337
20-370
20-257
20-305
20-338
20-371
20-258
20-306
20-339
20-372
20-259
20-307
20-340
20-373
20-260
20-308
20-341
20-374
20-261
20-309
20-342
20-375
20-262
20-310
20-343
20-376
20-263
20-311
20-344
20-377
20-264
20-312
20-345
20-378
20-265
20-313
20-346
20-379
20-266
20-314
20-347
20-380
20-267
20-315
20-348
20-381
20-268
20-316
20-349
20-382
20-269
20-317
20-350
20-383
20-270
20-318
20-351
20-384
20-271
20-319
20-352
20-385
20-272
20-320
20-353
20-386
Rev
PC200/220LC-7L
This is the sample of the manual Click on the download link for complete manual
Download Link
FOREWORD Mark
Page
Rev
Mark
Page
Rev
Mark
Page
Mark
Page
20-387
20-393
20-388
20-394
20-389
20-395
20-501
20-534
20-390
20-396
20-502
20-535
20-391
20-397
20-503
20-536
20-392
20-398
20-504
20-537
20-393
20-399
20-505
20-538
20-394
20-400
20-506
20-539
20-395
20-401
20-507
20-540
20-396
20-402
20-508
20-541
20-370
20-403
20-509
20-542
20-371
20-404
20-510
20-543
20-372
20-405
20-511
20-544
20-373
20-406
20-512
20-545
20-374
20-407
20-513
20-546
20-375
20-408
20-514
20-547
20-376
20-409
20-515
20-548
20-377
20-410
20-516
20-549
20-378
20-411
20-517
20-550
20-379
20-412
20-518
20-551
20-380
20-413
20-519
20-552
20-381
20-414
20-520
20-553
20-382
20-415
20-521
20-554
20-383
20-416
20-522
20-555
20-384
20-417
20-523
20-556
20-385
20-418
20-524
20-557
20-386
20-419
20-525
20-558
20-387
20-420
20-526
20-559
20-388
20-421
20-527
20-560
20-389
20-422
20-528
20-561
20-390
20-423
20-529
20-562
20-391
20-424
20-530
20-563
20-392
20-425
20-531
20-564
PC200/220LC-7L
20-426
Rev
Rev
20-532 20-533
00-2-5
FOREWORD Mark
Page
Rev
Mark
Page
Mark
Page
Rev
Mark
Page
20-565
20-615
30-13
30-46
20-566
20-616
30-14
30-47
20-567
20-617
30-15
30-48
20-568
20-618
30-16
30-49
20-569
20-619
30-17
30-50
20-570
20-620
30-18
30-51
20-571
20-621
30-19
30-52
20-572
20-622
30-20
30-53
20-573
20-623
30-21
30-54
20-574
20-624
30-22
30-55
20-575
20-625
30-23
30-56
20-576
20-626
30-24
30-57
20-577
20-627
30-25
30-58
20-578
20-628
30-26
30-59
20-579
20-629
30-27
30-60
20-580
20-630
30-28
30-61
20-581
20-631
30-29
30-62
20-582
20-632
30-30
30-63
20-633
30-31
30-64
20-634
30-32
30-65
30-33
30-66
20-601 20-602
00-2-6
Rev
20-603
30-1
30-34
30-67
20-604
30-2
30-35
30-68
20-605
30-3
30-36
30-69
20-606
30-4
30-37
30-70
20-607
30-5
30-38
30-71
20-608
30-6
30-39
30-72
20-609
30-7
30-40
30-73
20-610
30-8
30-41
30-74
20-611
30-9
30-42
30-75
20-612
30-10
30-43
30-76
20-613
30-11
30-44
30-77
20-614
30-12
30-45
30-78
Rev
PC200/220LC-7L
FOREWORD Mark
Page
Rev
Mark
Page
Rev
Mark
Page
Rev
Mark
Page
30-79
30-112
30-80
30-113
90-1
90-34
30-81
30-114
90-2
90-35
30-82
30-115
90-3
90-36
30-83
30-116
90-4
90-37
30-84
30-117
90-5
90-38
30-85
30-118
90-6
90-39
30-86
30-119
90-7
90-40
30-87
30-120
90-8
90-41
30-88
30-121
90-9
90-42
30-89
30-122
90-10
30-90
30-123
90-11
30-91
30-124
90-12
30-92
30-125
90-13
30-93
30-126
90-14
30-94
30-127
90-15
30-95
30-128
90-16
30-96
30-129
90-17
30-97
30-130
90-18
30-98
30-131
90-19
30-99
30-132
90-20
30-100
30-133
90-21
30-101
30-134
90-22
30-102
30-135
90-23
30-103
30-136
90-24
30-104
30-137
90-25
30-105
30-138
90-26
30-106
30-139
90-27
30-107
30-140
90-28
30-108
30-141
90-29
30-109
30-142
90-30
30-110
30-143
90-31
30-111
30-144
90-32
PC200/220LC-7L
Rev
90-33
00-2-7
FOREWORD Mark
00-2-8
Page
Rev
Mark
Page
Rev
Mark
Page
Rev
Mark
Page
Rev
PC200/220LC-7L
FOREWORD
SAFETY
12 SAFETY
SAFETY NOTICE
00
00
IMPORTANT SAFETY NOTICE
00
Proper service and repair is extremely important for the safe operation of your machine. The service and repair techniques recommended and described in this manual are both effective and safe methods of operation. Some of these operations require the use of tools specially designed for the purpose. To prevent injury to workers, the symbols and are used to mark safety precautions in this manual. The cautions accompanying these symbols should always be followed carefully. If any dangerous situation arises or may possibly arise, first consider safety, and take the necessary actions to deal with the situation.
GENERAL PRECAUTIONS
00
PREPARATIONS FOR WORK
00
Mistakes in operation are extremely dangerous. Read the OPERATION & MAINTENANCE MANUAL carefully BEFORE operating the machine.
1.
Before adding oil or making repairs, park the machine on hard, level ground, and block the wheels or tracks to prevent the machine from moving.
1.
Before carrying out any greasing or repairs, read all the precautions given on the decals which are fixed to the machine.
2.
2.
When carrying out any operation, always wear safety shoes and helmet. Do not wear loose work clothes, or clothes with buttons missing. Always wear safety glasses when hitting parts with a hammer. Always wear safety glasses when grinding parts with a grinder, etc.
Before starting work, lower blade, ripper, bucket or any other work equipment to the ground. If this is not possible, insert the safety pin or use blocks to prevent the work equipment from falling. In addition, be sure to lock all the control levers and hang warning signs on them.
3.
When disassembling or assembling, support the machine with blocks, jacks or stands before starting work.
4.
Remove all mud and oil from the steps or other places used to get on and off the machine. Always use the handrails, ladders or steps when getting on or off the machine. Never jump on or off the machine. If it is impossible to use the handrails, ladders or steps, use a stand to provide safe footing.
3.
If welding repairs are needed, always have a trained, experienced welder carry out the work. When carrying out welding work, always wear welding gloves, apron, glasses, cap and other clothes suited for welding work.
4.
When carrying out any operation with two or more workers, always agree on the operating procedure before starting. Always inform your fellow workers before starting any step of the operation. Before starting work, hang UNDER REPAIR signs on the controls in the operator's compartment.
5.
Keep all tools in good condition and learn the correct way to use them.
6.
Decide a place in the repair workshop to keep tools and removed parts. Always keep the tools and parts in their correct places. Always keep the work area clean and make sure that there is no dirt or oil on the floor. Smoke only in the areas provided for smoking. Never smoke while working.
PC200/220LC-7L
PRECAUTIONS DURING WORK
00
1.
When removing the oil filler cap, drain plug or hydraulic pressure measuring plugs, loosen them slowly to prevent the oil from spurting out. Before disconnecting or removing components of the oil, water or air circuits, first remove the pressure completely from the circuit.
2.
The water and oil in the circuits are hot when the engine is stopped, so be careful not to get burned. Wait for the oil and water to cool before carrying out any work on the oil or water circuits.
3.
Before starting work, remove the leads from the battery. ALWAYS remove the lead from the negative (-) terminal first.
00-3
FOREWORD
SAFETY
12 4. When raising heavy components, use a hoist or crane. Check that the wire rope, chains and hooks are free from damage. Always use lifting equipment which has ample capacity. Install the lifting equipment at the correct places. Use a hoist or crane and operate slowly to prevent the component from hitting any other part. Do not work with any part still raised by the hoist or crane. 5.
When removing covers which are under internal pressure or under pressure from a spring, always leave two bolts in position on opposite sides. Slowly release the pressure, then slowly loosen the bolts to remove.
6.
When removing components, be careful not to break or damage the wiring, Damaged wiring may cause electrical fires.
7.
When removing piping, stop the fuel or oil from spilling out. If any fuel or oil drips on to the floor, wipe it up immediately. Fuel or oil on the floor can cause you to slip, or can even start fires.
8.
As a general rule, do not use gasoline to wash parts.
9.
Be sure to assemble all parts again in their original places. Replace any damaged part with new parts. • When installing hoses and wires, be sure that they will not be damaged by contact with other parts when the machine is being operated.
10. When installing high pressure hoses, make sure that they are not twisted. Damaged tubes are dangerous, so be extremely careful when installing tubes for high pressure circuits. Also check that connecting parts are correctly installed. 11. When assembling or installing parts, always use the specified tightening torques. When installing protective parts such as guards, or parts which vibrate violently or rotate at high speed, be particularly careful to check that they are installed correctly. 12. When aligning two holes, never insert your fingers or hand. Be careful not to get your fingers caught in a hole. 13. When measuring hydraulic pressure, check that the measuring tool is correctly assembled before taking any measurements. 14. Take care when removing or installing the tracks of track-type machines. When removing the track, the track separates suddenly, so never let anyone stand at either end of the track.
00-4
PC200/220LC-7L
FOREWORD
GENERAL
12 GENERAL
00
This shop manual has been prepared as an aid to improve the quality of repairs by giving the serviceman an accurate understanding of the product and by showing him the correct way to perform repairs and make judgements. Make sure you understand the contents of this manual and use it to full effect at every opportunity. This shop manual mainly contains the necessary technical information for operations performed in a service workshop. For ease of understanding, the manual is divided into the following sections. These sections are further divided into each main group of components. GENERAL This section lists the general machine dimensions, performance specifications, component weights, and fuel, coolant and lubricant specification charts. STRUCTURE, FUNCTION AND MAINTENANCE STANDARD This section explains the structure, function and maintenance standard of each component. It serves not only to give an understanding of the structure, but also serves as reference material for troubleshooting. TESTING, ADJUSTING AND TROUBLESHOOTING This section explains checks to be made before and after performing repairs, as well as adjustments to be made completion of the checks and repairs. Troubleshooting charts correlating “Problems” to “Causes” are also included in this section. DISASSEMBLY AND ASSEMBLY This section explains the order to be followed when removing, installing, disassembling or assembling each component, as well as precautions to be taken for these operations. OTHER This section mainly gives hydraulic circuit diagrams and electric circuit diagrams. In addition, this section may give the specifications of attachments and options together.
NOTICE The specifications contained in this shop manual are subject to change at any time and without any advance notice. Contact your distributor for the latest information.
PC200/220LC-7L
00-5
FOREWORD
HOW TO READ THE SHOP MANUAL
12 HOW TO READ THE SHOP MANUAL
VOLUMES
00
Shop manuals are issued as a guide to carrying out repairs. They are divided as follows: Chassis volume: Engine volume:
Issued for every machine model Issued for each engine series
Electrical volume: Each issued as one to cover all models Attachment volume: Each issued as one to cover all models
00
REVISIONS
00
Revised pages are shown at the LIST OF REVISED PAGES between the title page and SAFETY page.
SYMBOLS
00
So that the shop manual can be of ample practical use, important places for safety and quality are marked with the following symbols. Item
Remarks
These various volumes are designed to avoid duplication of information. Therefore to deal with all repairs for any model, it is necessary that chassis, engine, electrical and attachment be available.
Safety
Special safety precautions are necessary when performing the work.
DISTRIBUTION AND UPDATING
Caution
Special technical precautions or other precautions for preserving standards are necessary when performing the work.
Weight
Weight of parts or systems. Caution necessary when selecting hoisting wire or when working posture is important, etc.
Tightening torque
Places that require special attention for tightening torque during assembly.
Coat
Places to be coated with adhesives and lubricants etc.
Oil, water
Places where oil, water or fuel must be added, and the capacity.
Drain
Places where oil or water must be drained, and quantity to be drained.
00
Any additions, amendments or other changes will be sent to your distributors. Get the most up-to-date information before you start any work.
FILING METHOD 1. 2.
Symbol
00
See the page number on the bottom of the page. File the pages in correct order. Following examples show how to read the page number: Example: 10 - 3 Item number (10. Structure and Function) Consecutive page number for each item
3.
Additional pages: Additional pages are indicated by a hyphen (-) and numbered after the page number. File as in the example. Example:
10-4 10-4-1 10-4-2
Added pages
10-5
REVISED EDITION MARK When a manual is revised, an edition mark ( recorded on the bottom outside corner of the pages.
00-6
00
…) is
PC200/220LC-7L
FOREWORD
HOISTING INSTRUCTIONS
12 HOISTING INSTRUCTIONS
can result. Hooks have maximum strength at the middle portion.
00
HOISTING
00
WARNING! Heavy parts (25 kg or more) must be lifted with a hoist etc. In the DISASSEMBLY AND ASSEMBLY section, every part weighing 25 kg or more is indicated clearly with the symbol 3.
1. 2.
If a part cannot be smoothly removed from the machine by hoisting, the following checks should be made: Check for removal of all bolts fastening the part to the relative parts. Check for existence of another part causing interface with the part to be removed.
WIRE ROPES 1.
Wire ropes (Standard “Z” or “S” twist ropes without galvanizing) Rope diameter
2.
WARNING! Slinging with one rope may cause turning of the load during hoisting, untwisting of the rope, or slipping of the rope from its original winding position on the load, which can result in a dangerous accident
00
Use adequate ropes depending on the weight of parts to be hoisted, referring to the table below:
Allowable load
mm
kN
tons
10
9.8
1.0
11.2
13.7
1.4
12.5
15.7
1.6
14
21.6
2.2
16
27.5
2.8
18
35.3
3.6
20
43.1
4.4
22.4
54.9
5.6
30
98.1
10.0
40
176.5
18.0
50
274.6
28.0
60
392.2
40.0
Do not sling a heavy load with one rope alone, but sling with two or more ropes symmetrically wound on to the load.
4.
Do not sling a heavy load with ropes forming a wide hanging angle from the hook. When hoisting a load with two or more ropes, the force subjected to each rope will increase with the hanging angles. The table below shows the variation of allowable load (kg) when hoisting is made with two ropes, each of which is allowed to sling up to 1000 kg vertically, at various hanging angles. When two ropes sling a load vertically, up to 2000 kg of total weight can be suspended. This weight becomes 1000 kg when two ropes make a 120° hanging angle. On the other hand, two ropes are subject to an excessive force as large as 4000 kg if they sling a 2000 kg load at a lifting angle of 150°
The allowable load value is estimated to be 1/6 or 1/7 of the breaking strength of the rope used. Sling wire ropes from the middle portion of the hook. Slinging near the edge of the hook may cause the rope to slip off the hook during hoisting, and a serious accident
PC200/220LC-7L
00-7