CAT Caterpillar 924K Service Repair Manual PDF Download by Heavy Equipment Manual

924K WHEEL LOADER

Printed by Heavy Equipment Manuals v2.20

Printed in U.S.A

Heavy Equipment Manuals

























































































































































  Product: WHEEL LOADER Model: 924K WHEEL LOADER KW4 Configuration: 924K Small Wheel Loader KW400001-UP (MACHINE) POWERED BY C7.1 Engine

Disassembly and Assembly 924K, 930K and 938K Wheel Loaders Power Train Media Number -UENR0281-03

Publication Date -01/04/2017

Date Updated -24/04/2017

i04768872

Accumulator (Hydrostatic) SMCS - 5077-H7

Specifications

Illustration 1

g02794681

Table 1 Specification for 373-6953 Accumulator Gp (HYDROSTATIC) Item

Qty

Part

Specification Description

224-5132 Cap

Charging medium is dry nitrogen.

Capacity of oil is 0.83 L (50.65 cubic inch)

Torque to 1.6 ± 0.1 N·m (14.2 ± 0.9 lb in).

Capacity of gas is 0.83 L (50.65 cubic inch).

Precharge pressure at 21.1 °C (70.0 °F) is 2150 ± 110 kPa (312 ± 16 psi).

Maximum operating pressure is 27500 kPa (3989 psi).

Maximum operating temperature is 121 °C (250 °F).

Removal Procedure Start By: a. Connect the steering frame lock. b. Release the hydraulic system pressure.

Personal injury can result from the sudden release of high pressure oil. Be sure the engine has been shut off for a minimum of five minutes to be sure that the accumulator pressure is zero. The accumulator is filled with dry nitrogen. Do not loosen or remove the valve or cap from the top of the accumulator. A purge screw at the bottom of the accumulator can be used to release the pressure that is left in the system.

Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.

This is the sample of the manual click onthe download link for complete manual

DOWNLOAD LINK For some reason if link does not work download this pdf and then click

Illustration 2

g02858296

1. Remove cover (1).

Illustration 3

g02867549

2. Disconnect hose assembly (2). 3. Loosen clamps (4) and remove hydrostatic accumulator (3).

Illustration 4

g02867557

4. Remove gas valve cap (5), the gas valve, and the O-ring seals.

Installation Procedure 1. Install hydrostatic accumulator (3) in the reverse order of removal. a. Tighten gas valve cap (5) to a torque of 1.6 ± 0.1 N·m (14.16 ± 0.89 lb in). Copyright 1993 - 2021 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees.

Fri Aug 27 10:44:32 UTC+0530 2021

Disassembly and Assembly 924K, 930K and 938K Wheel Loaders Power Train Media Number -UENR0281-03

Publication Date -01/04/2017

Date Updated -24/04/2017

i05268485

Axle Housing - Front and Rear Axle Housings SMCS - 3260 S/N - DYB1-UP S/N - ENC1-UP S/N - EYE1-UP S/N - FRK1-UP S/N - HJF1-UP S/N - KW41-UP S/N - P3K1-UP S/N - PWR1-UP S/N - REP1-UP S/N - RHN1-UP S/N - SNZ1-UP S/N - T681-UP S/N - W8K1-UP

Removal Procedure

Table 1 Required Tools Tool

Part Number

Part Description

Qty

1P-2420

Transmission Repair Stand

6V-2156

Link Bracket

4C-8502

Spanner Wrench As

1H-3107

Puller Group

5F-7343

Puller Group

1P-0074

Slide Hammer Puller

1U-8697

Duo-Cone Seal Installer As

Loctite High Flex GM

Start By: A. Remove the axle trunnion (front and rear) on the oscillating axle housing. B. Remove the fixed axle. Note: Cleanliness is an important factor. Before the disassembly procedure, thoroughly cleaned the exterior of the component to help prevent dirt from entering the internal mechanism. 1. Drain the oil from the axle housing into a suitable container for storage or disposal. The capacity of the axle housing is approximately 17.4 L (4.6 US gal).

Illustration 1

g00663942

2. Place axle assembly (1) on Tooling (A) . The weight of axle housing assembly (1) is approximately 590 kg (1300 lb).

3. Attach a suitable lifting device to axle housing assembly (1) . The weight of axle housing assembly (1) is approximately 147 kg (325 lb). Remove bolts (2) and remove axle housing assembly (1) .

Illustration 2

g00670398

Illustration 3

g00670395

4. Position the axle housing on Tooling (A) , as shown. Install bolt (3) in the axle, as shown. 5. Remove retaining ring (4) .

Illustration 4

g00670400

6. Install Tooling (B) and a suitable lifting device to carrier assembly, as shown. The weight of carrier assembly (5) is approximately 28 kg (62 lb). Remove carrier assembly (5) .

Illustration 5

g00891526

Illustration 6

g00670403

7. Drive pins (6) into shaft (7) . 8. Use a suitable press to remove shaft (7) . Remove gear (8) and washers (9) . 9. Remove pins (6) from shaft (7) .

Illustration 7

g00670404

10. Remove bearing (10) from gear (8) . 11. Repeat Steps 7 through 10 for the remaining two gears.

Illustration 8

g00670405

Illustration 9

g00670407

12. Use Tooling (C) in order to remove nut (11) .

Illustration 10

g00670410

13. Attach Tooling (B) and a suitable lifting device to axle housing (13) . The weight of axle housing (13) is approximately 88 kg (195 lb). Use Tooling (D) in order to separate axle housing (13) from the axle shaft. 14. Remove bearing cone (12) .

Illustration 11

g00891527

15. Use Tooling (F) in order to remove bearing cup (15) . Note: Removal of ring gear (16) will destroy the ring gear. 16. Use one of the following methods in order to remove ring gear (16) . Use a torch in order to cut ring gear (16) at pins (14) . Make three welds around the inside of ring gear (16) . This will cause ring gear (16) to shrink. 17. Remove pin (14) .

Illustration 12

18. Remove seal (17) .

g00670663

Illustration 13

g00670664

19. Use Tooling (F) in order to remove bearing cup (18) .

Illustration 14

20. Use Tooling (G) to remove seal (19) .

g00670665

Illustration 15

g00670676

21. Position the axle on Tooling (A) , as shown. 22. Use Tooling (E) in order to remove bearing cone (20) .

Installation Procedure Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.

Illustration 16

g00671305

1. Use Tooling (G) in order to install seal (19) . Refer to Disassembly and Assembly, "Duo-Cone Conventional Seals - Install" for the proper procedure. Note: Lubricate the bearing with the lubricant that is being used. 2. Raise the temperature of bearing cone (20) . 3. Install bearing cone (20) .

Illustration 17

g00671344

4. Lower the temperature of bearing cup (18) . 5. Install bearing cup (18) . Use Tooling (G) in order to install seal (17) . Refer to Disassembly and Assembly, "Duo-Cone Conventional Seals - Install" for the proper procedure.

Illustration 18

g01132120

6. Lower the temperature of bearing cup (15) . 7. Install bearing cup (15) . 8. Lower the temperature of ring gear (16) and install ring gear (16) . Install pins (14) and peen the housing in order to retain pins (14) .

Illustration 19

g00671536

9. Use a suitable lifting device and Tooling (B) in order to install axle housing (13) onto the axle shaft. The weight of axle housing (13) is approximately 88 kg (195 lb). Use Tooling (A) in order to support axle housing (13) . 10. Raise the temperature of bearing cone (12) . 11. Install bearing cone (12) . 12. Lubricate bearing cone (12) with the lubricant that is being sealed.

Illustration 20

g00670405

Illustration 21

g00670407

Note: Lubricate nut (11) with the lubricant that is being sealed. 13. Install nut (11) . Use Tooling (C) in order to tighten nut (11) . Leave slight bearing end play.

Illustration 22

g00671551

14. Use Tooling (A) in order to support the axle shaft. Install Tooling (D) , as shown. Install a bolt in the center of Tooling (D) . Use a torque wrench in order to rotate the axle housing and check the rolling torque (SD) . This is the amount of seal drag. 15. Use Tooling (C) in order to tighten nut (11) . Check the rolling torque (RT) . This is the total rolling torque. Subtract the seal drag torque (SD) from the total rolling torque (RT) . This is the rolling torque of the axle bearings. Tighten nut (11) until a rolling torque of the axle bearings is 3 N·m to 8 N·m (27 lb in to 70 lb in). The rolling torque for used axle bearings should be 2 N·m to 4.5 N·m (18 lb in to 40 lb in).

Illustration 23

g00670404

16. Install bearing (10) in gear (8) .

Illustration 24

17. Install gear (8) and washers (9) . 18. Install shaft (7) .

g00671595

Illustration 25

g01131675

Note: The openings of pins (6) must be 180 degrees away from each other. The openings of pins (6) must be parallel to the carrier deck. Refer to illustration 25. 19. Install pins (6) . 20. Deform pin holes slightly with a chisel. 21. Repeat Steps 16 through 19 for the remaining gear assemblies.

Illustration 26

g00670400

22. Use Tooling (B) and a suitable lifting device in order to install carrier assembly (5) . The weight of carrier assembly (5) is approximately 28 kg (62 lb).

Illustration 27

g00670395

23. Install retaining ring (4) . 24. Use a suitable lifting device in order to remove the axle housing from Tooling (A) . The weight of the axle housing is approximately 147 kg (325 lb).

Illustration 28

g01132124

25. Clean the mating surfaces of the axle housing and apply a continuous bead of Tooling (H) .

Illustration 29

g00663942

26. Use a suitable lifting device in order to install axle housing (1) . The weight of axle housing assembly (1) is approximately 147 kg (325 lb). Install bolts (2) . End By: a. Install the axle trunnion (front and rear) on the oscillating axle housing. b. Install the fixed axle housing. Copyright 1993 - 2021 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees.

Fri Aug 27 10:53:05 UTC+0530 2021

Disassembly and Assembly 924K, 930K and 938K Wheel Loaders Power Train Media Number -UENR0281-03

Publication Date -01/04/2017

Date Updated -24/04/2017

i04642161

Axle Housing - Front Axle SMCS - 3260 S/N - FRK1-UP S/N - HFW1-UP S/N - KW41-UP S/N - P3K1-UP S/N - REP1-UP S/N - SNZ1-UP S/N - SWL1-UP S/N - T681-UP S/N - W8K1-UP S/N - XXT1-UP

Removal Procedure Table 1 Required Tools Tool

Part Number

138-7576

Part Description Link Bracket

Qty 1

241-3790

Link Bracket

1U-6400

Three Jaw Puller

1U-5230

Hand Hydraulic Pump

Start By: a. Remove the front axle.

Illustration 1

g02786949

1. Attach Tooling (A) and suitable lifting devices to front axle (2). The weight of front axle (2) is approximately 1270 kg (2800 lb). Use Tooling (A) and the suitable lifting devices in order to position front axle (2) to the outside of wheel (1). Install four bolts (3) in order to secure front axle (2) to wheel (1). Note: This step must be done on a flat level surface. 2. Use Tooling (A) and the suitable lifting devices in order to set wheel (1) so that front axle (2) is in a verticle position with wheel (1) resting flat on the ground.

Illustration 2

g02859660

3. Remove fittings (4.)

Illustration 3

g02859677

4. Remove bolts (5) and the locking nuts in order to remove the parking brake caliper. Attach Tooling (D) in order to release the parking brake.

Illustration 4

5. Remove brake rotor (6).

g02859696

Illustration 5

g02787117

6. Remove tube assembly (7) and hose assemblies (8) from front axle (2).

Illustration 6

g02787176

7. Attach Tooling (A) and a suitable lifting device to final drive and brake housing (9). The weight of final drive and brake housing (9) is approximately 218 kg (480 lb). Remove bolts (10). Use Tooling (A) and the suitable lifting device in order to remove final drive and brake housing (9) and the O-ring seal.

Illustration 7

g02787278

Illustration 8

g02788226

8. Remove sun gear shaft (11). Note: Sun gear shaft (11) may come off with the final drive and brake housing (9) or stay with the axle shaft when the final drive and brake housing (9) is removed. 9. Remove shim (12). Note: Shim (12) may be located on the end of the axle shaft or inside sun gear shaft (11).

Illustration 9

g02788323

10. Attach Tooling (B) and a suitable lifting device to axle housing (13). The weight of axle housing (13) is approximately 172 kg (380 lb). Remove bolts (14). Use Tooling (B) and the suitable lifting device in order to remove axle housing (13).

Illustration 10

g02788436

11. Remove O-ring seal (15) and bearing cup (16) from axle housing (13).

Illustration 11

g02788477

12. Remove shim (17).

Illustration 12

13. Remove axle shaft (18).

g02788486

This is the sample of the manual click on the download link for complete manual

DOWNLOAD LINK For some reason if link does not work download this pdf and then click