CAT Caterpillar 924F Service Repair Manual PDF Download by Heavy Equipment Manual

924F WHEEL LOADER

Tip: Use Bookmarks panel to navigate Printed by Heavy Equipment Manuals v2.20

Printed in U.S.A

Heavy Equipment Manuals

 



 



 



 







 



 



 































































































































































































































































































































































































This is the sample of the manual click on the download link for complete manual

DOWNLOAD LINK For some reason if link does not work download this pdf and then click

  Product: WHEEL LOADER Model: 924F WHEEL LOADER 4YN Configuration: 924F Wheel Loader 4YN00001-UP (MACHINE) POWERED BY 3114 Engine

Disassembly and Assembly 446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines, IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G Wheel Loaders Media Number -SENR3611-18

Publication Date -01/05/2009

Date Updated -27/05/2009

i06818876

Aftercooler - Install SMCS - 1063-012

Installation Procedure Table 1 Required Tools Tool

Part Number

Part Description

Qty

Loctite Gasket Sealant No.2

Loctite C5-A Copper Anti-Seize

NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

Note: Use a new gasket to install the aftercooler.

Illustration 1

g00746356

Note: Apply Tooling (A) to the threads of the bottom bolts before installation. 1. Install gasket (9) on the engine. Install aftercooler (10). Install bolts (8). 2. Tighten clamp (6) and tighten clamp (7).

Illustration 2

g00746355

3. Tighten clamp (4). 4. Connect coupling (5).

Illustration 3

g00508837

Illustration 4

g00508835

Note: Apply Tooling (B) to the threads of the exhaust elbow bolts. 5. Install exhaust elbow (1) and exhaust pipe (3). Install bolts (2). 6. Fill the cooling system. Refer to Operation and Maintenance Manual, SEBU7098, "Cooling System Level - Check" for the correct procedure. Copyright 1993 - 2021 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees.

Wed Apr 28 02:51:19 UTC+0530 2021

Publication Date -01/05/2009

Date Updated -27/05/2009

i01929472

Aftercooler - Remove SMCS - 1063-011

Removal Procedure Table 1 Required Tools Tool

Part Number

8T-0292

Part Description

Qty

Bolt

NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates.

At operating temperature, the engine coolant is hot and under pressure. Steam can cause personal injury. Check the coolant level only after the engine has been stopped and the fill cap is cool enough to touch with your bare hand. Remove the fill cap slowly to relieve pressure. Cooling system conditioner contains alkali. Avoid contact with the skin and eyes to prevent personal injury.

Note: Put identification marks on all hose assemblies, on all wires, and on all tube assemblies for installation purposes. Plug all hose assemblies and tube assemblies. This helps to prevent fluid loss and this helps to keep contaminants from entering the system. 1. Drain the coolant from the cooling system into a suitable container for storage or disposal.

Illustration 1

g00508835

Illustration 2

g00508837

2. Remove bolts (2). Remove exhaust elbow (1) and exhaust pipe assembly (3).

Illustration 3

3. Loosen clamp (4). 4. Disconnect coupling (5).

g00746355

Illustration 4

g00746356

5. Loosen clamps (6) and (7). 6. Remove two top bolts (8) and install Tooling (A). Remove remaining bolts (8). Remove aftercooler (10). 7. Remove gasket (9) from aftercooler (10). Copyright 1993 - 2021 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees.

Wed Apr 28 02:51:06 UTC+0530 2021

Publication Date -01/05/2009

Date Updated -27/05/2009

i01931416

Air Compressor - Remove and Install SMCS - 1803-010

Removal Procedure

Do not disconnect the air lines until the air pressure in the system is at zero. If hose is disconnected under pressure it can cause personal injury.

NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates.

1. Remove the air pressure from the air tank and drain the coolant from the cooling system.

Illustration 1

g00484206

Typical example

2. Disconnect hose assemblies (1), (2) and (9) from the air compressor. Remove tube assembly (4) from the air compressor. 3. Remove bolt (5) and the washer. Remove clamp (7) from tube assembly for the breather. Move the tube assembly for the breather aside. 4. Remove bolts (3) and the washers that hold the air compressor to the timing gear housing. 5. Remove bolts (6) and remove air compressor (8) and the gasket from the engine.

Installation Procedure Table 1 Required Tools Tool

Part Number

Part Description

Qty

4C-4030

Thread Lock Compound

NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

Note: Check the condition of the gaskets and O-ring seals. If gaskets or O-ring seals are damaged, use new parts for replacement.

Illustration 2

g00484206

Typical example

1. Use bolts (3) and the washers to install air compressor (8). Apply Tooling (A) to the threads of bolts (6). Torque bolts (6) to 160 ± 30 N·m (118 ± 22 lb ft). 2. Install clamp (7) for the tube assembly for the breather with bolt (5) and the washer. 3. Install tube assembly (4) and connect hose assemblies (9), (2) and (1) to air compressor (8). Copyright 1993 - 2021 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees.

Wed Apr 28 03:05:22 UTC+0530 2021

Publication Date -01/05/2009

Date Updated -27/05/2009

i05024711

Air Compressor Drive Gear - Remove and Install SMCS - 1803-010-GE

Removal Procedure Table 1 Required Tools Tool

Part Number

Part Description

Qty

1P-2320

Combination Puller

9S-1730

Socket

Start By: A. Remove the air compressor.

NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

Illustration 1

g03196216

1. Temporarily install air compressor (1) with bolts (2) . Remove cover plate (3) .

Illustration 2

g03196337

2. Loosen nut (2) . Remove bolts (2) and remove air compressor (1) .

Illustration 3

g03196436

3. Remove nut (4) .

Illustration 4

g03196416

4. Use Tooling (A) in order to remove gear (5) .

Installation Procedure

Illustration 5

g03196438

1. Clean the inside diameter of gear (5) and the shaft. Lube the washer and the shaft thread with engine oil. Position drive gear (5) on the air compressor, and install the washer and nut (4) . Tighten nut (4) hand tight.

Illustration 6

g03196337

2. Install air compressor (1) and bolts (2) . Keep the engine from turning and tighten nut (4) to a torque of 170 ± 15 N·m (125 ± 11 lb ft)

Illustration 7

g03196477

3. Install Tooling (B) onto nut (4) and tap one time a hammer.

Illustration 8

g03196516

4. Keep the engine from turning and tighten nut (4) to a torque of170 ± 15 N·m (125 ± 11 lb ft)

Illustration 9

g03196496

Wed Apr 28 03:05:36 UTC+0530 2021

Publication Date -01/05/2009

Date Updated -27/05/2009

i01930386

Alternator - Remove and Install SMCS - 1405-010

Removal Procedure Table 1 Required Tools Tool

Part Number

Part Description

Qty

168-0383

Circuit Breaker Bar

Illustration 1 Typical Example

g00609523

Note: Release the tension on the belt at the belt tightener, if the engine is not equipped with a belt tensioner. 1. Use Tooling (A) to release the tension on belt tensioner (5). 2. Remove drive belt (4) from the drive pulley on alternator (3). 3. Place an index mark on the wires of harness assembly (1) that are connected to the alternator. Disconnect harness assembly (1) from the alternator. 4. Remove bolts (2). 5. Remove alternator (3) from the mounting bracket.

Installation Procedure Table 2 Required Tools Tool

Part Number

Part Description

Qty

168-0383

Circuit Breaker Bar

Illustration 2

g00609523

Typical example

1. Position alternator (3) on the mounting bracket. Install bolts (2). 2. Use Tooling (A) to install drive belt (4) on the drive pulley of the alternator. Note: Adjust the tension on the drive belt if the engine is not equipped with a belt tensioner. Refer to the Operation and Maintenance Manual for the correct adjusting procedure.

3. Connect harness assembly (1) to the alternator. Use the index marks to correctly connect the harness assembly. Tighten the mounting bolt for the ground wire to a torque of 6.2 ± 0.6 N·m (54 ± 5 lb in). Tighten the mounting bolt for the battery wire to a torque of 11.3 ± 2.3 N·m (100 ± 20 lb in). Copyright 1993 - 2021 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees.

Wed Apr 28 03:04:56 UTC+0530 2021

Publication Date -01/05/2009

Date Updated -27/05/2009

i05977048

Bearing Clearance - Check SMCS - 1203-535; 1219-535

Measurement Procedure Table 1 Required Tools Tool

Part Number

Part Description

Qty

198-9142

Plastic Gauge (Green) 0.025 to 0.076 mm (0.001 to 0.003 inch)

198-9143

Plastic Gauge (Red) 0.051 to 0.152 mm (0.002 to 0.006 inch)

198-9144

Plastic Gauge (Blue) 0.102 to 0.229 mm (0.004 to 0.009 inch)

198-9145

Plastic Gauge (Yellow) 0.230 to 0.510 mm (0.009 to 0.020 inch)

Note: Plastic gauge may not be necessary when the engine is in the chassis.

NOTICE

Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

Note: Cat does not recommend the checking of the actual bearing clearances particularly on small engines. This is because of the possibility of obtaining inaccurate results and the possibility of damaging the bearing or the journal surfaces. Each Cat engine bearing is quality checked for specific wall thickness. Note: The measurements should be within specifications and the correct bearings should be used. If the crankshaft journals and the bores for the block and the rods were measured during disassembly, no further checks are necessary. However, if the technician still wants to measure the bearing clearances, Tooling (A) is an acceptable method. Tooling (A) is less accurate on journals with small diameters if clearances are less than 0.10 mm (0.004 inch).

NOTICE Lead wire, shim stock or a dial bore gauge can damage the bearing surfaces.

The technician must be very careful to use Tooling (A) correctly. The following points must be remembered: • Ensure that the backs of the bearings and the bores are clean and dry. • Ensure that the bearing locking tabs are properly seated in the tab grooves. • The crankshaft must be free of oil at the contact points of Tooling (A). 1. Put a piece of Tooling (A) on the crown of the bearing that is in the cap. Note: Do not allow Tooling (A) to extend over the edge of the bearing. 2. Use the correct torque-turn specifications in order to install the bearing cap. Do not use an impact wrench. Be careful not to dislodge the bearing when the cap is installed. Note: Do not turn the crankshaft when Tooling (A) is installed. 3. Carefully remove the cap, but do not remove Tooling (A). Measure the width of Tooling (A) while Tooling (A) is in the bearing cap or on the crankshaft journal. Refer to Illustration 1.

Illustration 1

g01152855

Typical Example

4. Remove all of Tooling (A) before you install the bearing cap. Note: When Tooling (A) is used, the readings can sometimes be unclear. For example, all parts of Tooling (A) are not the same width. Measure the major width in order to ensure that the parts are within the specification range. Refer to Specifications Manual, "Connecting Rod Bearing Journal" and Specifications Manual, "Main Bearing Journal" for the correct clearances. Copyright 1993 - 2021 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees.

Wed Apr 28 03:03:04 UTC+0530 2021

Publication Date -01/05/2009

Date Updated -27/05/2009

i01930316

Belt Tensioner - Remove and Install SMCS - 1358-010

Removal Procedure

Illustration 1

g01011962

1. Use a breaker bar to release the tension on belt tensioner (1). Remove the drive belt. 2. Remove bolt (2) and belt tensioner (1).

Installation Procedure

Illustration 2

g01011962

1. Position belt tensioner (1) on the cylinder block. Install bolt (2). 2. Install the drive belt. Use a breaker bar to release tension on belt tensioner (1). Copyright 1993 - 2021 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees.

Wed Apr 28 03:04:10 UTC+0530 2021

Publication Date -01/05/2009

Date Updated -27/05/2009

i01930280

Belt Tightener - Install SMCS - 1358-012

Installation Procedure

Illustration 1

g00619355

1. Position water pump belt tightener (3) and install V-belt (2) on the pulley of water pump belt tightener (3). 2. Install bolts (1) that hold water pump belt tightener (3) to the timing gear housing.

This is the sample of the manual click on the download link for complete manual

DOWNLOAD LINK For some reason if link does not work download this pdf and then click