Operating and safety instructions.
For further information on the operation and care of our Finstral products, please refer to the instructions in our document “Operating and safety instructions. Windows.” You can find it at: finstral.com/manuals
• If the window closure is motor-driven, do not push it by hand. If the window tilting or opening is motor-driven, do not pull the element by hand. This could damage the chain drive.
• Keep the lever in a safe place. It is required in case of a manual emergency operation.
Safety and cleaning instructions
Further safety instructions and general information on window cleaning can be found in the instructions for use of windows (“Operating and safety instructions. Windows.”) at: finstral.com/manuals
Window in tilt position
This is how you bring the window into the tilt position via the wall switch.
Opening via the key
1. Press the “Open” key once.
2. The LED lights up green.
3. The window tilts independently in several seconds. As soon as the window is fully tilted, the green LED goes off.
Closing via the key
1. Press the “Close” key once. The window closes and locks independently for several seconds. The LED lights up red.
2. When the window is completely closed, the green LED flashes briefly.
Window with a gap in the ventilation position.
This method can be used to stop the window during the tilting process. A gap ventilation position is created.
1. Press the “Open” button once during the movement (during opening or closing).
2. The window stops during the opening or closing process.
Window in 10-minute tilt position
With the 10-minute tilt position, the window tilts independently and closes after 10 minutes. This setting is useful if you want to ventilate the room via a tilted window for 10 minutes.
1. Press the “Open” key twice.
3. The window is in the tilt position for 10 minutes. The LED flashes green.
2×
2. The green LED lights up, the window tilts independently.
4. After 10 minutes, the window closes and locks independently. The green LED lights up briefly. The window is then in the closed position.
Reference operation
A reference operation must be carried out after a power failure. The following safety instructions must be observed:
Safety instructions
• If the maximum permissible force of 150N is exceeded when closing the window (due to wind load), the drive returns to its starting position.
• After 60 seconds, the drive attempts to close the window again, and the LED flashes red-green. After the second failed attempt, the window remains open and the LED flashes red.
Procedure
• If necessary, check your windows for any obstructions and remove them. Press the “Close” button again 1x
1. Switch on the power. The LED flashes red and the drive beeps 20 times.
2. Press the “Close” key once. The LED then flashes briefly. The drive references itself automatically. 20x
Manual
When operating manually during an emergency, the tilt commands for motor-driven components are not active. Manual emergency operation is carried out via the milling in the sash frame and may only be carried out by a qualified personnel. Therefore, if necessary, contact the technical service of the installation company and under no circumstances carry out the manual emergency operation yourself.
Opening via the key
Press the “Open” key once. The window tilts independently in several seconds.
1x
Closing via the key
Press the “Close” key once. The window closes independently over several seconds.
Safety and cleaning instructions
On Page 4, observe the notes on the fanlight with a concealed motor. Further safety instructions and general information on window cleaning can be found in the instructions for use for windows (“Operating and safety instructions. Windows.”) at: finstral.com/manuals
1x
Problem Cause
The fanlight with a concealed motor beeps several times and stops. The LED flashes continuously.
The fanlight with an overlying motor beeps several times and tries up to three times to slowly move to the “Close” position. (After the third attempt, the drive stops). The LED flashes continuously.
The fanlight with motor shows no reaction when the push-button or the remote control is operated.
High wind pressure
Draught
Solution
Wait until the wind pressure decreases.
Eliminate the cause of the draught.
The fittings are blocked or too stiff. If necessary, remove the blockage or contact the installation company’s technical service.
Power failure
High wind pressure
Draught
Fix the voltage failure and perform a reference run.
Wait until the wind pressure decreases.
Eliminate the reason for the draught.
The fittings are blocked or too stiff. If necessary, remove the blockage or contact the installation company’s technical service.
No power supply
The wiring is incorrect/defective or the cable is defective.
The power supply unit is faulty/ defective.
The battery of the radio remote control is low.
Check the power supply.
Contact the technical service of the installation company.
Replace the battery.
Problem Cause
The fanlight with motor does not tilt or close.
There is no power supply.
Solution
Check the power supply.
The fittings are blocked or too stiff. Contact the technical service of the installation company.
The fittings are too smoothrunning.
The drive is dirty.
Especially during tilting: The fanlight is already tilted.
Especially when closing: The fanlight is already closed.
Check the drive for dirt and clean it if necessary.
Check the position of the window sash.
Copyright © Finstral AG, Unterinn/Ritten, 2025
All rights reserved.
The Finstral logo is a registered image mark of Finstral AG. The name “Finstral” is a registered word mark of Finstral AG.
Edition May 2025 Item number 60-0309-00-07
Subject to technical changes. Colour may differ from original products owing to printing processes. The presentation and description of the products in the prospectuses are for indicative purposes only. Should the product delivered deviate in any way from the product appearing in the advertising material, this shall not constitute any defect or deviation as only the order may be used as a benchmark.
Talk directly to a specialist consultant: Visit partner: finstral.com/dealer-search
Chat online: finstral.com
Your nearest Finstral partner:
Finstral Studio Unterinn
Headquarters, 600 m2 exhibition area
Unterinn/Ritten, Italy
T +39 0471 296611
finstral.com/unterinn
Finstral Studio Borehamwood
Showroom, 210 m2 exhibition area
Premiere House, Elstree Way
T +44 (0)20 80500584
Borehamwood, Hertfordshire, WD6 1JH finstral.com/borehamwood