BIGMASTER
DEUTZ-FAHR BIGMASTER Series
ULTIMATE FIELD PERFORMANCE, MAXIMUM OUTPUT
CAPACITY Our goal is to develop machines that will give a boost to the profi tability of your company. High output is a key success factor for every large square baler. DEUTZ-FAHR large square balers feature several unique points that will provide the capacity your company requires.
SQUARE BALES Perfectly shaped, consistently square bales are the end-result every customer is looking for. With over 30 years of experience in large square baling, our machines can produce rock-hard bales.
RELIABILITY To achieve maximum efficiency from your machine, unrivalled reliability is a must. The DEUTZ-FAHR large square balers are designed with simple, but efficient techniques. The result is a minimum downtime machine in which you can truly trust. BIGMASTER 578
3x2
80 x 70 cm
BIGMASTER 5712
120 x 70 cm
BIGMASTER 598
80 x 80 cm 4x2
3x3
3x3
80 x 90 cm
BIGMASTER 5912
120 x 80 cm
BIGMASTER 598D
80 x 90 cm 4x3
120 x 90 cm
BIGMASTER 5912D
120 x 90 cm
4x3
4-5 POWER DENSITY
CONSISTANT BALE SHAPE
POWER DENSITY The continuously rotating feeder fork combines two functions into one mechanism thereby eliminating the need for complex drivelines.
THE IMPORTANCE OF BALE SHAPE Consistently shaped bales bring more than just aesthetic appeal. A consistently filled bale represents quality in every form. Square bales are easy to stack and handle. In addition, they are much more stable during transport than a poorly formed bale. With silage, a perfectly square bale indicates less air content, resulting in high quality feed!
Power Density pre-chamber
6-7 PRE-CHAMBER
COMFORT AND QUALITY
HOW DOES IT WORK? The INTEGRAL ROTOR actively delivers the crop to the pre-chamber throughout which, in the initial phase, it is evenly distributed by the feeder fork.Regardless of the swath form, the POWER DENSITY system guarantees a perfectly filled pre-chamber.
PRE-CHAMBER A unique feature is the inspection hatch in the bottom of the prechamber. For easy access to the pre-chamber the complete under-side can be opened without using tools. Pre-chamber inspection door to further improve machine performance in wetter crops, an easy flow kit can be fitted to the pre-chamber. The Teflon plates result in a perfect crop flow in wet, sticky material.
The measuring wedges are positioned at the top of the prechamber (red). When these measure the correct density, the filling stroke is activated and the feeder fork is used to empty the pre-chamber and fill the bale chamber. PRE-CHAMBER INSPECTION DOOR
8-9 INTAKE
IT ALL STARTS WITH THE INTAKE
INTEGRAL ROTOR INTEGRAL ROTOR All DEUTZ-FAHR BIGMASTER balers, cutting or non-cutting versions are equipped with the INTEGRAL ROTOR. This simple, maintenance free intake system ensures even feeding regardless of the various (crop) conditions. The short distance between rotor and pick-up yields an outstanding crop flow. This force-fed intake makes higher forward speeds possible for outstanding productivity and reduced crop damage.
INTEGRAL ROTOR FOR ALL BIGMASTER MODELS
INTAKE The pick-up of the DEUTZ-FAHR BIGMASTER is designed to match the full capacity of the machine. With an intake width of 230 cm, the machine is capable of working in all swaths. The reliable cam track system will not let you down, even in the harshest conditions. To adapt the machine to your purposes, you have the choice between fixed and pivoting pick-up wheels.
10-11 INTEGRAL ROTOR
INTEGRAL ROTOR TECHNOLOGY
CUTTING VERSIONS OPTIFEED - NON CUTTING VERSION When crop cutting is not required, the OPTIFEED system ensures a controlled and consistent crop flow to the prechamber. With the rotor, an additional level of protection is added to the machine.
OC - CUTTING VERSIONS The OC cutting systems are designed for unlimited intake capacity. There are three different types of OC cutting system (availability dependent on Bigmaster model):
- OC 10 The OC 10 provides a theoretical cutting length of 70 mm. The knives have an individual spring type protection and can be engaged from the tractor cab.
- OC 15 The OC 15 offers a cutting length of 45 mm. The patented rotor tine shape ensures a low power requirement and a perfect cutting quality. The knives, individually protected with a spring, can be changed easily with the standard cassette system.
- OC 23 The OC 23 offers a cutting length of 45 mm on the 120 cm wide machine. With a rotor diameter of 60 cm, the OMNICUT rotor will process every swath that is placed in front of the baler. The knives on the OC 23 have individual hydraulic protection. This ensures a perfect cutting quality regardless of working speed and crop. With just two levers the operator can easily choose from the following knife group configurations: 0 – 11 – 12 – 23. Together with the standard cassette system for easy knife changing, you not only invest in cutting quality but, above all, in driver comfort.
INTEGRAL ROTOR TYPE BIGMASTER
KNIFE CASSETTE SYSTEM
KNIFE SELECTION
Optifeed Without cutting device
OC 10 70 mm cutting lenght
BIGMASTER 578
x
x
BIGMASTER 598
x
x
BIGMASTER 598D
x
BIGMASTER 5712
x
OC 15 45 mm cutting lenght, cassette
OC 23 45 mm cutting lenght, cassette
x x
BIGMASTER 5912
x
x
BIGMASTER 5912D
x
x
*patent or patent pending in one or more countries
12-13 BALE CHAMBER
NON STOP BALING
THE BALE CHAMBER PLUNGER The 46 plunger strokes per minute result in a high compaction capacity. The plunger is guided via 4 large rollers with a diameter of 125 mm for maximum service life.
BALE CHAMBER The specially designed bale chamber of the DEUTZ-FAHR BIGMASTER machines is the result of more than 30 years’ experience in big square baling. With the 3 meter long bale chamber, there is plenty of space to form a perfect bale. The combination of aggressive retainers and pressure door shape brings an aggressive compaction and gentle expansion of the bale.
3 M (9’ 10”) BALE CHAMBER, WITH LAST BALE EJECTION *patent or patent pending in one or more countries
BOTTOM RETAINERS PREVENT DECOMPRESSION OF THE BALE AND PROVIDE EXTRA DENSITY
14-15 BALE CHAMBER
PERFECTLY SHAPED BALES WITH CONSISTENT DENSITY
DENSITY REGULATION DENSITY REGULATION DEUTZ-FAHR BIGMASTER balers are known for their perfectly shaped bales with consistent density. The density can be regulated in two ways according to the driver’s preference. Using the conventional setting, the density is directly regulated from the terminal. With the automatic setting, the machine detects the load and automatically adjusts the pressure on the bale channel. Switching between the two settings is quick and easy resulting in a versatile, easy to operate machine.
MOISTURE To give you the best possible information about your crop and your machine, the Bigmaster baler can be equipped with a moisture sensor. This option gives you a good indication of the current crop moisture level.
LAST BALE EJECTOR To guarantee safe transport on the road, the last bale ejector is used to remove the last bale from the chamber.
MOISTURE SENSOR
LAST BALE EJECTOR
16-17 PROTECTION
ROBUST DRIVELINE AND MAXIMUM SECURITY
PROTECTION INSTANT PROTECTION To use the machine at maximum capacity, a flawless protection system is required. All main intake components of the DEUTZ-FAHR BIGMASTER balers are fitted with a cam type clutch. With this non-stop safety system you can unblock the machine from the operator seat. The pickup, Integral Rotor and feeder fork are protected with cam-type torque limiters, which are automatically activated in the event of an overload. The respective cam clutch then activates and the intake is stopped. The clutch re-engages when the operator reduces the PTO speed. Another benefit of these clutches is that they give the ability to drive at a constant speed without worrying about blockages.
INTEGRAL ROTOR PROTECTION CLUTCH
SYNCHRONIZED DRIVE Synchronized drive of components is made via gears and shafts. This ensures a perfectly synchronized machine with easy maintenance.
18-19 KNOTTING
A SOLUTION FOR EVERYBODY
KNOTTING TWIN STEP KNOTTING
DOUBLE KNOTTING
The unique TWIN STEP knotting system compromises a single knotter and smart system that releases the twine tension during the knotting cycle. The result is a secure, easy to adjust knotting system.
The BIGMASTER 598D and BIGMASTER 5912D are equipped with a double knotting system. With the electronic knotter control, the driver has accurate information concerning twine tension at all times and receives an alarm in case of risk. The knotting progress can be monitored directly from the tractor cab.
While baling, the knotters (blue) are at rest and the twine is guided by the twine tension release lever (red), in the vertical position. Tension is held on the twine to ensure maximum density in the bale. Step 1: As the bale reaches the desired length, the needles (grey) are activated and move upwards towards the knotters to start the knotting cycle. Step 2: By pivoting backwards the tension lever (red) releases the twine and consequently reduces tension to the knotter during the knotting cycle. This guarantees a perfect knotting process.
1
2
During baling, an upper (blue) and lower (red) twine is fed to the bale, because the twine is not slipping around the bale there is no tension on the twine during the bale formation. Step 1: As the bale reaches the desired length, the needles (grey) are activated and move upwards to the knotter to start the knotting cycle. In this first step the bale is finished with the first knot. Step 2: Once the first knot has finished the bale, the second knot connects the upper and lower twine again so the bale can be formed without stress on the twine during knotting.
1
2
KNOTTING One of the last steps in creating a perfect bale is the knot. With the knotting options on your DEUTZ-FAHR BIGMASTER you can be sure of a reliable and secure knotting system that meets your requirements.
KNOTTER CLEANING
TWIN STEP MODELS ELECTRIC KNOTTER FANS
DOUBLE KNOTTER MODELS HYDRAULIC DRIVEN FANS
20-21 MAINTENANCE
MAINTENANCE AND ACCESSABILITY
TWINE BOXES TWINE BOXES The twine boxes swing out completely for easy access to the vital parts of the machine. Behind the full-access side doors, spools of twine can be stored. The twine storage itself is enclosed to prevent twine rolls from being contaminated with detritus, which could cause mis-ties. To reduce daily maintenance and to preserve your machine, the automatic central greasing system is fitted on most models. The twine boxes on the single knotter models are capable of storing up to 24 twine spools. An extra option is a moveable service light. It can be plugged in at 3 convenient places and provide you with light where you need it. The BIGMASTER double knotter models have a twine capacity of 30 x 13 kg spools and integrated dust protection through shielding of the twine boxes. The double knotter models are equipped as standard with 4 LED service lights to inspect your machine. As an option, there is a choice of 3 additional LED work lights to have a clear view all night long.
STORAGE HOSES For clean & tidy storage, the BIGMASTER is equipped with a convenient stowage place for the hoses and cables needed to operate the machine.
SHIELDING AND TWINE BOXES
AUTOMATIC GREASING SYSTEM
LED WORK LIGHTS
LED SERVICE LIGHTS
22-23 ELECTRONICS
ALWAYS IN CONTROL
ELECTRONICS ISOBUS All DEUTZ-FAHR BIGMASTER balers are ISOBUS compatible. ISOBUS compatible tractors will therefore not require a separate control box for the baler. Alternatively, the VT 50 or CCI 200 monitor can be used with tractors that are not ISOBUS compatible. Operator settings such as bale density and knife activation are accessed via the terminal. Operator warnings as overload, twine routing and operator information, including flakes per bale and number of bales are also provided.
FULL VISIBILITY To provide optimal visibility and safety around the machine, the BIGMASTER can be equipped with a camera system. There are 2 versions available; one version is compatible with the CCI 200 terminal, the other comprises a separate monitor and a camera.
CCI 200 VT 50 The DEUTZ-FAHR ISOBUS VT 50 terminal has a 14,5 cm (5.7�) color screen with outstanding clarity. Adjustments can easily be done by the touch screen and the large soft-touch keys on the sides. The VT 50 terminal can be used for all DEUTZ-FAHR ISOBUS machines.
The ISOBUS compatible CCI 200 terminal has a large 21.6 cm (8.5�) colour screen with outstanding clarity. Machine adjustments can be easily made via the touch screen or with the intuitive, large soft keys. The CCI 200 terminal can also be used with many other ISOBUS compatible machines on the market.
24-25 PRE-CHOPPING
PRE-CHOPPING AT ITS FINEST
CBB 200 CBB 200 Providing high quality forage, bedding and feeding is one of the main development goals for DEUTZ-FAHR machinery. The CBB 200 pre-chopper has a specific design that matches the capacity and machine characteristics of the BIGMASTER baler range. With this combination, you will be able to produce an even higher quality baled product.
SMOOTH AND SHORT
MAXIMUM VERSATILITY
With the industry leading 670 mm rotor, the CBB ensures a smooth running of the machine and a low power requirement. To ensure a perfect cut, and an aggressive damaging of the stem, the machine is equipped with 48 cutting blades and 2 counter knife banks giving a total of 98 counter knives. This results in a theoretical cutting length of 19.5 mm.
The working height of the CBB offers a wide range of adjustment over for maximum adaptation to the given conditions and circumstances. With a ground clearance of 65 cm, the CBB 200 can remain on the machine when pre-chopping is not required. The drawbar is specially designed to match both the CBB 200 and the BIGMASTER balers, creating harmony between the two machines.
26-27 TRACK AND TRACE
ALL YEAR LONG
TRACK AND TRACE TRACK AND TRACE – ADDING VALUE DEUTZ-FAHR BIGMASTER balers can be combined with Harvesttec equipment for big balers. If you require an preservative applicator, dye spray marker or bale tagging system, please contact your local DEUTZ-FAHR dealer or DEUTZ-FAHR representative in your country.
DYE SPRAY MARKER
WM 4034 The Wrapmaster 4034 offers a solid design and a hydraulic sliding feature that allows unique “drive through” operation. This provides the ability to widen the wrapper for easy bale loading, outstanding stability and unmatched visibility of the wrapping process.
WRAPMASTER 4034
BALE TAGGING SYSTEM
28-29 OVERVIEW
8 4
5
6
2
1
7
1
INTEGRAL ROTOR TECHNOLOGY
MACHINE HIGHLIGHTS
2
PRE-CHAMBER INSPECTION DOOR
OVERVIEW 5
3
CAM CLUTCH PROTECTION OF INTAKE COMPONENTS
6
HIGH CAPACITY PLUNGER - 46 STROKES PER MINUTE 12,5 CM DIAMETER PLUNGER ROLLERS
7 3
POWER DENSITY PRE-CHAMBER
3 M (9’ 10”) BALE CHAMBER, WITH LAST BALE EJECTION
8
4
HINGED TWINE STORAGE BOXES FOR EASY MACHINE ACCESS
AUTOMATIC + MANUAL BALE DENSITY CONTROL
30-31 OPTIONS
ELECTRIC BALE LENGTH ADJUSTMENT
AUTOMATIC GREASING SYSTEM
OPTIONS
MOISTURE SENSOR INTEGRATED IN ISO ELECTRONICS
BALE DROP SENSOR
HITCH OPTIONS AVAILABLE
WORKING LIGHT OPTIONS
EASY FLOW
BIGMASTER SPECIFICATIONS
Balers with 80 crop flow channel
Balers with 120 crop flow channel
BigMaster BigMaster BigMaster BigMaster BigMaster BigMaster BigMaster BigMaster BigMaster BigMaster BigMaster BigMaster 578 578 OC 598 598 OC 598 D 598D/OC 5712 5712 OC 5912 5912 OC 5912D 5912D/OC BALE DIMENSIONS Width
80 cm (32”)
80 cm (32”)
80 cm (32”)
120 cm (47”)
120 cm (47”)
120 cm (47”)
Height
70 cm (28”)
80 cm (32”) 90 cm (35”)
90 cm (35”)
70 cm (28”)
80 cm (32”) 90 cm (35”)
90 cm (35”)
Length
60 cm (24”) up to 300 cm (118”)
PICK-UP Intake width
210 cm (83”)
230 cm (91”)
Pick-Up diameter
34 cm (13”)
Number of tine bars
4
5
Tine spacing
61 mm (2.4”)
BALE CHAMBER Number of plunger strokes
46 / min
Plunger stroke length
695 mm (27”)
Density control
3 hydraulic cylinders
4 hydraulic cylinders
Bale chamber length
300 cm (9’ 10”)
Controls
ISOBUS (VT50 / CCI200)
KNOTTERS Number of knotters Knotting system Knotting cleaning
4 TWINSTEP (optional)
6
TWINSTEP
Electric fans
Double knotter
TWINSTEP (optional)
TWINSTEP
Double knotter
Blowers
Electric fans optional blower
Electric fans optional blower
Blowers
Electric fans
Twin spool capacity
24
30
24
30
INTAKE SYSTEM INTEGRAL ROTOR
Optifeed
Opticut
Optifeed
Opticut
Optifeed
Opticut
Optifeed
Omnicut
Optifeed
Omnicut
Optifeed
Omnicut
Knives
-
0/10
-
0/10
-
0/15
-
0/11/12/23
-
0/11/12/23
-
0/11/12/23
Theoretical cutting length
-
70 mm (2¾”)
-
70 mm (2¾”)
-
45 mm (1¾”)
-
45 mm (1¾”)
-
45 mm (1¾”)
-
45 mm (1¾”)
Knives protection
-
Individual spring
-
Individual spring
-
Individual spring
-
Individual spring
-
Individual spring
-
Individual spring
x
x
x
x
WHEELS AND AXLES** Single axle 600/50-22.5
Hydraulic or pneumatic brakes x
x
x
x
x
600/55-22.5 710/40R22.5
x
x
x
x
Tandem axle
x
x
x
x
x
x
x
x
x
x
Standard steering and suspension, hydraulic or pneumatic brakes
400/70-20
x
x
x
x
x
x
x
x
500/55-20
x
x
x
x
x
x
x
x
x
x
x
x
560/45R22.5
x
x
x
x
x
x
x
x
x
x
x
x
620/50R22.5
x
x
x
x
x
x
x
x
x
x
x
x
DIMENSIONS Length
780 cm (25’7”)
800 cm (26’3”)
800 cm (26’3”)
800 cm (26’3”)
Width
276 cm (9’1”)
276 cm (9’1”)
300 cm (9’10”)
300 cm (9’10”)
Height
270 cm (8’10”)
326 cm (10’7”)
275 cm (9’)
326 cm (10’7”)
Weight*** Minimum tractor requirement
7900 kg 8200 kg 8000 kg 8300 kg 8600 kg 8900 kg 8800 kg 9450 kg 9200 kg 9850 kg 9700 kg (17415 lbs) (18075 lbs) (17635 lbs (18295 lbs) (18960 lbs) (19620 lbs) (19400 lbs) (20830 lbs) (20280 lbs) (21715 lbs) (21385 lbs) 66 kW (90 hp)
74 kW (100 hp)
70 kW (95 hp)
77 kW (105 hp)
77 kW (105 hp)
88 kW (120 hp)
81 kW (110 hp)
99 kW (135 hp)
Power requirement may vary with different crops, conditions and options used. Consult operators manual for proper tractor sizing. ** Depending on local homologation *** Depending on version an additional options
88 kW (120 hp)
107 kW (145 hp)
103 kW (140 hp)
10350 kg (22815 lbs) 121 kW (165 hp)
Printed in the Netherlands - Order no.: ZPDH06GB A 02-15
Dealer
The use of original lubricants and coolants is recommended. DEUTZ-FAHR LUBRICANTS
DEUTZ-FAHR is a brand of deutz-fahr.com