Issuu

Still shining: stainless steels in architecture China and India: growing domestic end uses of nickel materials THE MAGAZINE DEVOTED TO NICKEL AND ITS APPLICATIONS

August 2015, Vol. 30, No. 2

Better batteries for transport and sustainable energy grids

T he first issue of Nickel e magazin

2 30TH ANNIVERSARY OF NICKEL MAGAZINE

nickel, vol. 30, no. 2, august 2015

NICKEL, VOL. 30, NO. 2, AUGUST 2015

The Magazine Devoted to Nickel and its Applications Nickel magazine is published by Nickel Institute www.nickelinstitute.org David Butler, President Clare Richardson, Editor crichardson@nickelinstitute.org Contributors: Gary Coates, Catherine Houska, Bruce McKean, Geir Moe, Eric Partington, Thierry Pierard, Clive Whittington Design: Constructive Communications

THIRTY YEARS OF EVOLUTION AND INNOVATION

Nickel Institute can be contacted at: Eighth Floor Avenue des Arts 13-14 Brussels 1210, Belgium Tel. +32 2 290 3200 communications@nickelinstitute.org

Everything in the first editorial of Nickel of 30 years ago (see page opposite) remains true. Well, almost everything: “the non-socialist world” is a phrase one doesn’t see much these days.

Material has been prepared for the general information of the reader and should not be used or relied upon for specific applications without first securing competent advice. While the material is believed to be technically correct, Nickel Institute, its members, staff and consultants do not represent or warrant its suitability for any general or specific use and assume no liability or responsibility of any kind in connection with the information herein. ISSN 0829-8351 Printed in Canada on recycled paper by Hayes Print Group

In Focus Editorial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Special Feature Batteries and nickel . . . . . . . . . . . . . . . . . 4-5 Stainless steel and architecture . . . . . . 6-7 India and China: nickel use 30 years on . . . . . . . . . . . . . 10-11 In Use Stainless steel in Japan . . . . . . . . . . . . . . . . 8 Food safety . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Surface finishing . . . . . . . . . . . . . . . . . . . . . 12 Refuge du Goûter . . . . . . . . . . . . . . . . . . . 13 Fondation Louis Vuitton . . . . . . . . . . . . . 16 14 14 14 15 15 15

Others Metal goods 5% Transport | 18% 21% | | Building and construction 7.5%—

1985 Engineering— 27.5%

Metal goods 18% Building and | construction 10%—

Electrical, — electronic 21%

13%—r Tubular products

Others 6% Transport | 15% |

2013

SOURCE: PARISER

Where nickel goes: 1985 vs 2013

TABLE OF CONTENTS

nickel, vol. 30, no. 2, august 2015

Some of those are revisited in this issue to show how strength, durability, enhanced corrosion resistance, aesthetics and recyclability, are still being exploited to our collective advantage albeit in ways that reflect our increasing sophistication in working with materials. That’s the evolutionary part and the charts below show how our understanding of where nickel goes looks quite similar to three decades ago.

Cover: Constructive Communications Cover image: 30 years of Nickel magazines, Constructive Communications

In Brief New President . . . . . . . . . . . . . . . . . . . . . . . Nickel compounds explained . . . . . . . . UNS details . . . . . . . . . . . . . . . . . . . . . . . . . . Nitinol robots . . . . . . . . . . . . . . . . . . . . . . . . Shape memory alloy . . . . . . . . . . . . . . . . . Web links . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Yet politics do not alter the qualities of nickel and nickel-containing materials, which remain constant. How those qualities are being deployed in support of improved products and environments are direct descendants of what industry and society was expecting of nickel in 1985.

Electrical, — electronic 11% — Engineering 27%

Similar, but not the same. Demand for nickel has almost trebled over the past three decades and those broad end-use categories mask many internal shifts. Nickel in coinage is down, nickel in chemicals for batteries is up. And that brings us to innovation. The editor of Nickel 30 years ago would recognise some of the engineering and architectural story lines but would be amazed at the news coming from pure and applied research where nickel is either essential to the research or essential to the resulting products. Economic and environmental imperatives are driving material science to new levels and, along the way, new uses—even new properties—of nickel are being explored and applied to the benefit of society and the environment. Nickel will continue to report on both the evolutionary and innovative uses of nickel. There will be lots of stories to tell.

Clare Richardson Editor, Nickel magazine

NICKEL IN FOCUS 3

Decades of past and future service nickel in batteries remains essential

atteries are becoming ever more important for the global goal of sustainability and nickel is playing its part. While the first nickel battery (nickel-iron battery patented by the Edison Laboratory in 1901) has been around for over a century, the last three decades have seen extraordinary changes in the nature and composition of cells that, when connected in parallel or series or both, give us batteries. Also, the uses to which those batteries are being put are constantly expanding. And while not as obvious as when the common chemistries were nickel cadmium (NiCd) and nickel metal hydride (NiMH), nickel remains prominent in innovative lithium ion batteries for stationary, portable and motive energy.

They are also becoming more complex . Now cells and batteries are designed to maximise the desired parameters: specific voltages, voltage stability, specific energy and specific power (amount of available energy by volume or mass), speed of recharging, heat generation or any trade-offs between these and other parameters. Manufacturers now design to the performance of today’s diverse availability of batteries or discuss with battery manufacturers their needs. And manufacturers have more and more options for meeting diverse specifications. It’s a dynamic scene. This, in turn, means that it is impossible to predict what comes next. A safe bet, however, is that nickel in combination with other metals and minerals will only increase in importance as the shift from carbon-based energy continues.

The Taiwanese company Gogoro has announced that as of June 2015 it is taking pre-orders for its SmartscooterTM. It will have swappable batteries, free dedicated charging stations, top speed of 95km/h, acceleration to 50km/h in 4.2 seconds, cutting edge design…and nickel in the NCA batteries.

Today’s nickel-dependent battery chemistries Nickel Zinc (NiZn): A rechargeable version of the nickel oxyhydride battery. High self-discharge rate but higher energy-to-mass and power-to-mass ratios because they are 75% lighter than equivalent lead acid batteries. They have a fast rate of charging and are price competitive with NiCd batteries. Nickel Cadmium (NiCd): Once a dominant battery type for portable tools, it has evolved technologically and still has significant end-uses in stationary emergency power situations such as railway signalling, emergency lighting and grid levelling (voltage maintenance) as well as emergency short-term grid power supply.

r The electric scooter for an island where 15 million of its 23 million citizens ride a scooter. The battery swap system uses Bluetooth® to recognise registered scooters and will release a fully charged battery for each depleted battery placed in an open slot. The exchange can take as little as six seconds per battery.

s E ach scooter has two Panasonictechnology NCA batteries, weighing a total of about 17kg.

4 NICKEL SPECIAL FEATURE

ISTOCK PHOTO.COM © KIRSTYPARGETER

The ‘Tesla’ of scooters

Nickel Metal Hydride (NiMH): It was an exciting emerging technology 30 years ago. It is now a mature technology that still fills many roles. It was and remains the dominant battery chemistry for electric vehicles as it powers all the Toyota® Prius models. Lithium Nickel Manganese Cobalt Oxide (NMC): A chemistry that can be tuned to deliver either high specific energy or high specific power, but not both. It is typically one-third nickel, one-third manganese and one-third cobalt but there are many variations to deliver different performance characteristics. It is the current power source of choice for electric tools, e-bikes and electric power trains. But not the Tesla… Lithium Nickel Cobalt Aluminum Oxide (NCA): This variation was the choice for Tesla vehicles. It shares similarity with NMC by offering high specific energy, good specific power and a long life span. The addition of aluminum brings greater stability to the chemistry.

nickel, vol. 30, no. 2, august 2015

TESLA MOTORS

v Available in white, blue or black, a Powerwall battery hangs next to a Tesla Model S. In both cases nickel is a major component of the battery chemistry.

Energy goes to the wall

o call the Tesla Powerwall® a game-changer understates the impact it is going to have on how electricity is generated, distributed and stored. The Powerwall challenges current models and responds in a cost-efficient way to the increasing complexity of electrical grids and the growing role of environmentally-driven (wind, solar, etc.) sources. And nickel is essential to this revolution. At this early stage technical details are scarce. It is known that the Tesla stationary storage battery for residential use weighs 100kg (see Specifications) and will use far fewer cells per unit than in the Tesla Model S. The number of Powerwall units, however, could number in the millions. More important: industrial and grid applications The attention and imagination of the public is centred on the residential applications. These are literally “close to home” and are designed with that in mind with choices of colour for the mounted battery systems. Potentially much more disruptive to the energy industry, however, are the scaled-up versions referred to as “power packs” that will compete with other energy storage systems to provide the traditional capacities of

POWERWALL SPECIFICATIONS Technology

Wall mounted, rechargeable nickel-containing lithium ion battery with liquid thermal control

Models

10kWh US$3,500 for backup applications 7kWh US$3,000 for daily cycle applications

Warranty

10 years

Efficiency

92% round-trip DC efficiency

Power

2.0kW continuous, 3.3kW peak

Voltage

350–450 volts

Current

5.8 amp nominal, 8.6 amp peak output

Compatibility

Single phase and three phase utility grid compatible

Operating Temperature

-20 °C to 43 °C

Weight

100kg

Dimensions

1300mm x 860mm x 180mm

nickel, vol. 30, no. 2, august 2015

peak shaving (storing off-peak energy), load shifting and voltage firming (voltage leveling). According to Tesla Energy, utility-scale systems will group individual 100kWh batteries for capacities ranging from 500kWh to 10MWH and greater. They are to be capable of two to four hours of continuous net discharge power to compensate for grid power in case of outages. This will be delivered by the same nickel-containing batteries of the Tesla automobiles and at a price estimated at about US$250/kW hour of capacity, a reduction of at least 50% from alternative technologies. It is still very early days. Performance and economics have yet to be severely tested but it is clear that the whole model of electrical power distribution, storage and use is being disrupted to the benefit of end-users (everyone) and the environment. s A combination of solar arrays and power pack units is expected to reduce energy costs by 40% for Jackson Family Wines of California.

NICKEL SPECIAL FEATURE 5

Buildings and Structures in Stainless Steel Nickel charts the progress N

ickel Institute consultants, workshops and literature have been a valued source of information for making the building and construction specification decisions for 30 years and work funded by the organisation has made new innovations possible. The pages of Nickel magazine have chronicled these contributions and journey—a look back at just the first 10 years provides insight into the Nickel Institute’s influence. Many of these projects have become iconic symbols of nickel-containing stainless steels’ contribution to durable sustainable design.

Gateway Arch

The gleaming polished Type 316 curves of the University of Minnesota’s Weisman Art Museum in Minneapolis, USA, show

CATHERINE HOUSKA

MIKE RENLUND

PHOTOS: CATHERINE HOUSKA

Many well-known stainless clad buildings graced the pages of Nickel during the first 10 years. The selection of Type 316L by César Pelli for the first building in London’s Canary Wharf business complex, One Canada Square, was announced in Nickel in June 1990. At 48 floors and 235 metres, it was the tallest habitable building in the United Kingdom and tallest building in Europe upon completion. Most of the other buildings in the complex and the spectacular subway entrance canopy also use Type 316L. (Figure 5)

Greenhouses can be very corrosive environments. 17km of Type 316L stainless steel glazing bars were used for the restoration of the historic Palm House at Kew Gardens in London, U.K. (March 1990). The traditional appearance had been maintained with white paint. (Figure 2) Type 316 (S31600) was also instrumental, although hidden, in restoring the architecturally-important 12th century

The design was so innovative in 1948 that stainless steel structural research was needed prior to construction to confirm that Type 304 (UNS S30400) stainless steel plate 6.35mm thick was a suitable load-bearing material for the exterior. That research lead to the world’s first structural design standard for stainless steel and was part of the reason why construction was delayed for thirteen years.

6 NICKEL FEATURE

The magazine has also highlighted cuttingedge applications in famous buildings, including the Louvre Pyramid in Paris, France (June 1991, Figure 3) which used nickel-containing Type 316L and 17-4PH (S17400) for the first large glass curtain wall supported entirely by stainless steel. The structural supports for the stainless and glass roof of the International Terminal of Waterloo Station in London, U.K. are Type 316 as is the roof and the diamond floor plate. (September 1993, Figure 4)

The Nickel Institute has helped fund structural research, specification and design guide development and as well as specifier education. Nickel has documented important structural restorations and new applications. The restoration of the Statue of Liberty was completed using nickel containing Type 316L (UNS S31603) and Alloy 255 (S32550) duplex stainless steel to support the famous copper skin. It replaced badly-corroded structural iron. (June 1986, Figure 1 below)

In June 1987, Nickel celebrated the Arch as “still shimmering like new, yet now 21 years old”. Eero Saarinen’s iconic Gateway Arch will be 50 years old in October 2015. The elegant gleaming silver arch is the world’s tallest memorial at an impressive 192 metres.

Catherine Houska, the stainless steel expert on the team that inspected it at the end of 2014, said ”the stainless steel is dirty because of its exposure to industrial pollutants but the discoloration is superficial. The Arch is in very good condition and should have no problems providing another 50 years of service.”

Santa Maria degli Amalfitani church in Monopoli, Italy. (March 1995)

Many construction materials require extensive maintenance, including repainting or replacement within as little as 20 years. Properly specified, stainless steel can provide hundreds of years of life. The formability, weldability and range of finishes available in nickel-containing stainless steels make them the material of choice for architects around the world.

Figure 1 Statue of Liberty, New York, USA

Figure 2 Palm House, Kew Gardens, London, U.K.

nickel, vol. 30, no. 2, august 2015

how Frank Gehry skillfully combined sculpture and architectural design in his first high profile stainless steel clad building. It constantly changes as it reflects its environment. (June 1994, Figure 6) Rona ld Reaga n Washington National Airport is the showplace gateway to the U.S. capital and features numerous exterior and interior applications. Its distinctive stainless steel roof used a specially developed very dull finish and started a global airport roof trend. (March 1995, Figure 7) Since longevity is such an important aspect of sustainable materials, the Nickel Institute also provides advice on cleaning and restoration. After cleaning, Chrysler Buildingâ€™s famous stainless steel roof (March 1995) still gleams on the New York skyline.

OUTOKUMPU

DAILYMATADOR

Whether the nickel-containing stainless steel is visible or hidden, it provides unparalleled performance relative to other architectural metals. While projects featured in Nickel represent a very small percentage of the projects influenced over the years by the Nickel Institute, their breadth is indicative of the important work done.

NICKEL INSTITUTE

Figure 4 Waterloo Station, London, U.K.

nickel, vol. 30, no. 2, august 2015

Figure 6 W eisman Art Museum, Minneapolis, USA

Figure 7 R onald Reagan Washington National Airport, Washington, DC, USA NICKEL FEATURE 7

OUTOKUMPU

CREDIT? OVERLY MANUFACTURING

Figure 5 One Canada Square, London, U.K.

WIKIMEDIA COMMONS

Figure 3 Louvre Pyramid, Paris, France

Stainless steel in Japan

PRODUCTION, USE, INNOVATION T

he first issue of Nickel magazine 30 years ago looked at new products and applications of nickel-containing stainless steel in Japan, which in 1985 was the world’s leading producer. Since then what has changed and what are the trends?

Over the years, application of nickel-containing stainless steel in Japan has shifted. In the 1960s and 1970s, kitchen utensils, appliances and fittings (the most common being sinks) drove the demand. Since the 1980s, construction applications, such as building materials, transportation vehicles and electric appliances have grown. Automotive applications saw increasing demand in the 1990s, represented by products that control automobile exhaust emissions, against a background of needs for environmental countermeasures. The trend has continued and many recent innovative applications also involve more sophisticated grades of stainless steel. In the civil engineering field, there has been increasing emphasis on the corrosion resistance of stainless steel. Stainless steel reinforcing bar with the advantage of a very long life (100 years plus) became standard in Japan in 2008 (JIS G4322). Another example was the use of a 6% molybdenum super-stainless steel SUS312L (UNS S31254) which has superior seawater corrosion resistance, and was used to clad the piers of the Haneda Airport D runway in Tokyo, which opened in 2010. In addition, stainless steel has come into use for many peripheral but essential materials in the construction and civil engineering fields: stainless steel pipes for housing complexes, water tanks, storage tanks, interior boards and mounting hardware for

COURTESY OF REIYUKAI

v The inaugural issue of Nickel in September 1985 featured black coloured stainless steel tiles on Tokyo’s Shakaden Temple. They are still spectacular today, virtually unchanged in appearance since their installation in 1975. s

8 NICKEL IN USE

…in recent years, the use of shaped Type 304 stainless steel for anti-seismic reinforcement of existing buildings has increased. tunnels, telephone exchange equipment containers, escape ladders, windbreak fences, tunnel louvres, foundation packing for wooden houses, exterior heat-insulating construction material, and stainless steel nuts and bolts. And in recent years, the use of shaped Type 304 (S30400) stainless steel for anti-seismic reinforcement of existing buildings has increased. Type 316L (S31603) stainless steel has also been used effectively in Tokyo’s water distribution system to withstand significant and frequent seismic activity. The installation of stainless steel distribution pipes, which started in the 1980s, has reduced the leakage rate from 20% to just 2%—claimed to be one of the lowest leakage rates of any metropolitan area. This technology has huge potential in a world where water availability is constrained. In many cities, 10-20% of the water is lost between the water treatment plant and the consumer, because of leaks in the pipes. One of the Nickel Institute’s objectives is to bring the Tokyo technology to other countries. Japan has had a special love for coloured stainless steel, both for interior and exterior applications since the 1970s. This too is now catching on in other parts of the world, for example on the roof of the Chinese Swimming Club in Singapore, featured in the March 2013 issue of Nickel. A stunning example is Tokyo’s Shakaden temple where black stainless steel tiles cover the 10,000m2 roof. It was featured in the first issue of Nickel and still looks spectacular today. s The Piers of the Haneda Airport D runway sit on the sea floor and are clad with corrosion resistant 6% Mo nickel-containing stainless steel.

CREATIVE COMMONS © YAMAGUCHI YOSHIAKI

While world production of nickel-containing stainless steel has continued to increase over the past three decades, growth in Japan has slowed. In contrast, stainless steel production in China has seen rapid expansion and today accounts for over half of world supply. Despite China’s rise, Japan is still placed as the number two producer, with over 8% of the world’s supply in 2014.

nickel, vol. 30, no. 2, august 2015

SAFE KEEPING food chain dependence on nickel materials

he Ethiopian famine was in the minds of many when the first issue of Nickel magazine appeared in 1985. It featured a story on how nickel-containing stainless steels were playing a significant role in food safety as well as reducing the wastage of food that occurs between the farmer and the consumer. Today, the food supply chain is even more internationalised and many countries have adopted food safety standards similar to those successfully employed in both Europe and North America. Those standards have gone through significant advances in the last 30 years and will continue to improve. But those same nickelcontaining stainless steel alloys have remained and will remain as the first choice for food contact surfaces for all food and beverage processing operations. Multiple challenges Keeping food safe is a challenge. It requires not only selecting the appropriate materials and proper equipment design but a rigorously enforced system to keep out dangerous contaminants. One of the more recent standard improvements is the definition of a product contact surface. It is not restricted to the obvious surfaces of the containers, conveyors and vessels on or in which food is processed or stored, but includes any surface from which contamination, whether deposited on the surface or a constituent of the material, could drip, splash or be blown onto the food. Moreover, these surfaces must all be hygienic. This does not just mean “always clean and shiny”, reassuring as that may be, but resistant to contamination and easily cleanable between uses. Enter the nickel-containing stainless steels, the most common alloys being Type 304 (UNS S30400), 304L (S30403) and 316L (S31603). Their corrosion resistance based on chromium and enhanced by nickel, is universally recognised: there is a stainless steel suitable for every food product from milk to mustard to the most demanding liquids such as soy sauce, where 6% Mo alloys are required. And sometimes the disinfecting chemicals are more corrosive than the food products themselves.

ISTOCK PHOTO.COM © AGLPHOTOPRODUCTIONS

Smooth surfaces To allow for proper cleaning and disinfection, food product contact surfaces, must be smooth. Both EHEDG (European Hygienic Engineering and Design Group) and 3-A Sanitary Standards (U.S.) recommend smoother surfaces than 30 years ago, and now call for a surface roughness of 0.8µm or less. This standard can be exceeded by a 2B finish on stainless steel sheet. A high quality no.4 polished finish will also meet that requirement. In addition, the hardness of stainless steel resists the abrasion (for instance from dry particulate foods) which can roughen a food contact surface to the point where biofilms can adhere so firmly to the surface that normal cleaning procedures cannot remove them. Outside Europe and North America, Australia, New Zealand and Japan have had rigorous standards for many years now and China is also upgrading its standards to world-class. The common element for all these countries is nickel-containing stainless steels as the materials of choice. nickel, vol. 30, no. 2, august 2015

NICKEL IN USE 9

nickel use supporting development

wo countries not mentioned in the first issue of Nickel magazine were China and India. Neither country was a major player in the international stainless steel market. What a difference 30 years makes! In 1985, India produced just over 1% of the world’s stainless steel, while China’s was much less. Today China stands as the largest stainless steel producer by far, with just over 50% of the world’s production, while India stands in a very respectable third spot, just behind Japan, but ahead of South Korea and the U.S. And while we may think of China and India as producers of standard commodity grades and lower end products, both countries are working hard to produce both higher alloyed nickel-containing stainless steels as well as nickel alloys. Two examples of applications in each country illustrate the large scale and innovative uses suited to their needs.

INDIAC ISTOCKPHOTO.COM © ANTON_SOKOLOV

GREAT LEAPS FORWARD:

India Stainless steel was first used for the shells of railcars in the U.S. in 1934, and has been widely adopted in North America, Australia and Japan. Many countries, including India, had not used stainless steel due to its perceived high cost despite well-known attributes such as very low maintenance and long life. Initial success came in 2002 with the Delhi Metro, and the use of Type 301LN (UNS S30153) for all coaches plus Type 304 (S30400) for the station furnishings and hardware. There are now 143 fully functional stations in the system, with more in different phases of completion. Other metro systems followed suit using Type 301LN coaches, including Jaipur, Chennai, Bangalore and Kochi. In addition, high speed passenger trains are now extensively being made using a combination of 300 and 400 series stainless steels at two new production facilities, with a projected volume of 4000 coaches per year.

10 NICKEL SPECIAL FEATURE

PHOTO COURTESY OF TERI

Another small, but innovative application that can help hundreds of millions of Indian families is a forced air stove, components of which are made in 300 and 200 series austenitic stainless steels. Burning biomass such as wood, crop residue and cattle dung is very common in rural areas for cooking applications. Traditional stoves have incomplete combustion. This results in emissions of toxic gases which, in poorly ventilated kitchens, is estimated to result in half a million premature deaths annually in India, primarily women and children. By using forced air from a fan powered by batteries, there can be a 70% reduction in smoke, a 50% reduction in fuel consumption while cutting the cooking time in half. Designed by TERI (The Energy and Resources Institute), the technology has been approved by the Ministry of New and Renewable Energy and is available to stove manufacturers to use.

nickel, vol. 30, no. 2, august 2015

ACHINA

A switch from gasoline powered vehicles to electric ones is a way to reduce air pollution in the major urban areas.

ISTOCKPHOTO.COM © FCKNIMAGES

China The rapid industrialisation of China has resulted in unacceptably high levels of pollution, especially air pollution. This is one of the major issues with which China is grappling, leading Premier Li Keqiang to declare ‘War on Pollution’ in March 2014.

A switch from gasoline powered vehicles to electric ones is a way to reduce air pollution in the major urban areas. Those batteries often contain nickel, either NMH (nickel metal hydride) or certain types of lithium ion batteries. (See story page 4) China was an early adopter of electric bikes, with over 120 million having been sold. While sales of all electric battery vehicles (BEVs) are still relatively low at just less than 60,000 vehicles in 2014, there are over 40 models currently to choose from in China. In addition, plug-in hybrid vehicles are also available, using batteries most often containing nickel.

ISTOCKPHOTO.COM © 4FR

In China, coal is still king—80% of its electricity is generated from this fuel (2014) and coal-fired power plants are still being built at a rate of one per week. One way to reduce the pollution burden is to build higher efficiency plants. Advanced Ultra Super Critical (AUSC) steam generation offers a solution. This technology is currently being worked on in China as well as in Europe, USA and Japan. (See Nickel Vol. 30 No. 1). These plants produce steam at 700 °C and higher, and mean that the standard steels are unsuitable. Both special nickel alloys and special stainless steels can handle the higher steam temperatures, allowing an efficiency of 50% or more. For the steam generator tubes, a modified 304 (9% nickel) with copper, niobium, nitrogen and boron additions shows promise for long term reliable performance. Both India and China have developed rapidly since the first issue of Nickel magazine 30 years ago, showing increasing levels of innovation. And we can be sure that nickel will still be an important part of the economy of these nations for the future. v Top left: Nickel-containing stainless steel rail passenger cars produced in India

PHOTO © SIEMENS AG

v Top right: Battery powered bicycles and scooters are ubiquitous today in China. v Bottom left: Forced air stove fabricated from austenitic stainless steel with electrically powered fans and rechargeable batteries for use with photovoltaic cells. It is corrosion resistant with smooth surfaces which are easy to clean and provides a safe and affordable solution for domestic cooking. v Bottom right: Steam turbine of type SST5-6000 at Yuhuan power plant

nickel, vol. 30, no. 2, august 2015

NICKEL SPECIAL FEATURE 11

STOCK.XCHNG

Bright future

Nickel surface finishing continues to be relevant in a changing world

uperficially, not a great deal has changed in the plating and electroforming industry. But beneath the surface—where the nickel is found—there have been enormous shifts not in the processes but in the products that depend on the processes. Products that were unheard of 30 years ago but which are now part of daily industrial and household life are made possible or better with nickel plating. The largest use of nickel is in metallurgical alloys such as high nickel alloys for heat and corrosion resistance, stainless and low alloys steels, non-ferrous alloys including coinage, and ferrous castings. But to the average consumer, the most obvious use of pure nickel is for plated coatings. From the humble paper clip, to attractive automotive trim, this widespread use reflects the useful properties of nickel as a coating, and its versatility. By modifying operating conditions, the properties and appearance of nickel can be customised to suit designers’ and consumers’ specific needs. Electroplated nickel is used extensively to enhance the utility, value and sales appeal of manufactured products. Other nickel coatings improve the physical properties such as wear, heat or corrosion resistance. In many important applications, nickel coatings serve the dual role of providing an attractive decorative coating plus imparting improved corrosion resistance or other functional properties. Over the 30 years since Nickel magazine was first published, the most notable developments in nickel plating have been the greater use of durable nickelchromium coatings on plastics and aluminium components. Bright, satin, pearl and black coatings are widely selected for automotive, motor cycle and commercial vehicle components, along with tapware and bathroom fittings, door and cupboard fittings, metal furniture, appliances and consumer electronics. An important application is electroforming, v Not just the “bright and shiny” aesthetic look but enhanced corrosion resistance too for automobile wheels.

12 NICKEL IN USE

where nickel is built up by electrodeposition onto a suitable mandrel, and subsequently removed to produce a nickel product which corresponds precisely to the

Nickel coatings improve the physical properties such as wear, heat or corrosion resistance. shape and texture of the original substrate. Examples are rotary textile printing screens, nickel foam battery electrodes, stampers for CD/DVDs/ holograms and security printing plates for bank notes and postage stamps. Electroless nickel plating is another method for depositing nickel onto a substrate. This is a chemical process which reduces nickel ions in a solution to nickel metal by chemical reduction, rather than with electric current. The unique properties of the resultant nickel deposit include uniform thickness, hardness, corrosion resistance and magnetic response. The largest application is for hard disc drives, while other examples are the metallising of plastics for electroplating, automotive brake cylinders, pumps, valves and other engineering products. The Nickel Plating Handbook provides practical information on the operation and control of nickel electroplating processes, plus important information on safety and environmental matters. Copies are available for download f rom www.nickelinstitute.org or from communications@nickelinstitute.org

nickel, vol. 30, no. 2, august 2015

necessary feature so that hikers and aircraft pilots would not be blinded as well as to ensure the refuge’s integration into the snowy environment.

A nickel-containing stainless steel refuge

ON THE ROOF OF EUROPE

for the refuge. Heat collectors on the roof, solar panels on the façade, the use of biomass produced internally, and the recycling of waste water mean the new refuge is nearly 100% energy and water self-sufficient.

osting 25,000 to 30,000 mountaineers each year, the new Refuge du Goûter, is at an elevation of 3,835 metres and located on the main route to Mont Blanc in the French Alps. Perched on a rocky cliff edge, it was designed to withstand temperatures ranging from -50°C to +30°C and winds that can reach 300 kph.

High-altitude assembly All the components were prepared by subcontractors in the valley then transported by helicopter to the platform for assembly on Mont Blanc. The stainless steel bands were assembled using flat Z-joints. To ensure the full aerodynamic effect around the shell, the stainless steel cladding, windows and solar panels had to be perfectly aligned in the same plane on each of the facets. Opened in 2013, the new Refuge du Goûter can accommodate 120 people and replaces a 1960s shelter which was no longer fit for purpose. At a cost of €6 million, it is an incredible feat of engineering and a sanctuary for climbers on their way to conquer the roof of Europe. Designers of the Refuge du Goûter: DécaLaage architectural agency, Chamonix, and Groupe H, Geneva.

PHOTOS: GUDRUN BERGDAHL – PASCAL TOURNAIRE

The refuge’s ovoid form is built perpendicular to the cliff for the least possible wind resistance. The wind currents meet at the rear of the building, depositing the snow they carry. A huge drift provides a permanent and renewable reserve of fresh water

Strong mechanical resistance, low reflectivity Wood was the preferred construction material because of its light weight and ease of construction at high elevations. However, because it was too fragile to withstand the extreme climatic conditions, the project architects and engineers came up with the solution of cladding the wooden structure. Nickel-containing stainless steel offered the necessary set of properties including long life and low maintenance in a cold environment—the surface would be cleaned naturally by the wind and snow. Low reflectivity from the sun was another

A complex set of facets Type 304 (EN 1.4301, UNS S30400) stainless steel containing 8.0% minimum nickel, with a Uginox “Top” finish was selected in two thicknesses: 0.5mm for the roof and 0.8 mm for the facade. This is a double-sided matte finish with a surface roughness of about 1.5µm. The structure comprises a complex puzzle of 128 facets evenly distributed over four levels (32 facets per level), in four basic dimensions: 2m x 4m (16 facets); 2m x 3m (48 facets); 1.3m x 3m (48 facets). Each facet was itself divided into four or seven bands of stainless steel measuring 2.50 and 2.80m in length. In all, nearly 800 stainless steel sheets were cut.

nickel, vol. 30, no. 2, august 2015

NICKEL IN USE 13

NICKEL INSTITUTE APPOINTS DAVID BUTLER AS PRESIDENT T

& General Counsel. David is an experienced

he Nickel Institute is pleased to announce that David Butler was appointed President, on 1 June 2015. David succeeds Tim Aiken who retired af ter being associated with the Nickel Institute for 25 years.

lawyer specialising in advising Fortune

500 clients, private companies and trade associations. Nickel Institute Chairman, Robert Morris said, “We look forward to the continuing

David Butler has been involved with the Nickel Institute for over 25 years, firstly in his role as external legal counsel and Corporate Secretary, and then joining the Nickel Institute in 2013 as Executive Director

contribution of David in his new role as President and are confident that the NI’s very positive momentum will continue under his leadership.”

Nickel compounds explained

he Nickel Institute has published Nickel Compounds, the inside story..., a free 16-page guide to nickel compounds written for non-specialists by industry experts.

Nickel Compounds, the inside story... shows how nickel compounds are essential to a wide range of industrial sectors including transport, aerospace, marine and architectural applications and for the manufacture of many consumer goods. “Most people do not realise the importance of nickel compounds in the functioning of everyday products like cars and electronics,” said Clare Richardson, Communications Manager, Nickel Institute. “This publication explains in simple terms what nickel compounds

UNS details UNS

are and why they are so widely used. It explains where nickel is an essential material and central to or supportive of virtually all technologies.” She added, “Nickel Compounds, the inside story...reveals the crucial contribution of nickel compounds in the value chain and why nickel has a key role to play in society now and for a long time to come.” Nickel Compounds, the inside story... can be downloaded from the Nickel Institute website or requested from: communications@nickelinstitute.org

Chemical compositions (in percent by weight) of the alloys and stainless steels mentioned in this issue of Nickel.

N01555 p. 15

0.07 max.

0.05 max.

0.01 max.

0.05 max.

0.005 max.

0.025 max.

54.057.0

0.05

bal.

S17400 p. 6

0.07 max.

15.017.5

3.005.00

bal.

1.00 max.

0.150.45

3.005.00

0.040 max.

0.030 max.

1.00 max.

S30153 p. 10

0.030 max.

16.018.0

bal.

2.00 max.

0.070.20

6.08.0

0.045 max.

0.030 max.

1.0 max.

S30400 p. 6,8,9,10,13

0.08 max.

18.0020.00

bal.

2.00 max.

8.0010.50

0.045 max.

0.030 max.

1.00 max.

S30403 p. 9

0.03 max.

18.0020.00

bal.

2.00 max.

8.0012.00

0.045 max.

0.030 max.

1.00 max.

S31254 p. 8

0.020 max.

19.5020.50

0.501.00

bal.

1.00 max.

6.006.50

0.1800.220

17.5018.50

0.030 max.

0.010 max.

0.80 max.

S31600 p. 6

0.08 max.

16.0018.00

bal.

2.00 max.

2.003.00

10.0014.00

0.045 max.

0.030 max.

1.00 max.

S31603 p. 6,8,9,16

0.030 max.

16.0018.00

bal.

2.00 max.

2.003.00

10.0014.00

0.045 max.

0.030 max.

1.00 max.

S31803 p. 16

0.030 max.

21.023.0

bal.

2.00 max.

2.503.50

0.080.20

4.506.50

0.030 max.

0.020 max.

1.00 max.

14 NICKEL IN BRIEF

nickel, vol. 30, no. 2, august 2015

Flexible Nitinol robots could transform surgery S

cientists from Leibniz University, Hannover, Germany, are collaborating with research teams at the Vanderbilt University in Nashville, USA, to develop tiny flexible snake-like robots which will allow surgeons to access difficult-to-reach spaces with minimal invasion. Nitinol (UNS N01555), the bio-compatible nickel titanium alloy frequently used in stents, catheters or braces, has been chosen for its shape memory properties and super elasticity. Dr. Jessica Burgner-Kahrs from the Hannover Center for Mechatronics at Leibniz University is leading research into how robots fitted with tentacle-like arms made of several tiny superelastic Nitinol tubes could transform delicate brain surgery. A team from the Vanderbilt University is researching the removal of hematomas in the brains of stroke patients using the robots, in a project funded by the National Institutes of Health. Unlike conventional robots which have joints and rigid connections, ‘continuum robots’ feature a continuous structure

which is inspired by bionics—think elephant’s trunk or snake. Because of the shape memory properties, the small tube can be bent and once the deforming pressure decreases it will return to its original shape. Ultimately this elasticity could allow the robot to move along curves in tiny spaces within the human body to reach areas previously too dangerous to access. The Nitinol robot has potential applications in sinuses, for access to the pituitary gland as well as removing hemorrhagic fluid or clots from the brain.

UNIVERSITY OF KIEL IN COOPERATION WITH AQUANDAS GMBH

LEIBNIZ UNIVERSITAET HANNOVER

s An American ten cent piece (approximately 18mm in diameter) shows the scale of the Nitinol robot.

Toughest ever

NICKEL

shape memory alloy P

rofessors Manfred Wuttig and Eckhard Quandt at the Universities of Maryland, USA and Kiel, Germany, have produced a new shape memory alloy so tough it returns to its original shape even after being bent and heated over ten million times. This makes the new alloy, a mixture of titanium, nickel and copper, a candidate for “high cycle” applications such as artificial heart valves and solid state air conditioners. In contrast the previous highest-performing shape memory alloy could be deformed approximately 16,000 times before it succumbed to fatigue. All shape memory alloys are phase-changing materials, meaning they can shift into

nickel, vol. 30, no. 2, august 2015

MAGAZINE ONLINE

www.nickelinstitute.org SUBSCRIBE to Nickel magazine free of charge and receive a printed copy or an e-mail notice when a new issue is posted online. www.nickel institute.org/NickelMagazine/Subscription

r 50µm thick NiTiCu thin film linear tensile actuator different molecular configuration—such as water into ice. The new alloy’s transition can be “activated” by heat in one of its forms, and by a release of tension in another. Wuttig and Quandt discovered that the key to the alloy’s durability was the presence of a small impurity, a precipitate of titanium and copper (Ti2Cu). These particles were compatible with both of the alloy’s phases, allowing it to mediate millions of complete and reproducible transformations thereby reducing fatigue.

READ Nickel magazine online in several languages. www.nickelinstitute.org/ NickelMagazine/MagazineHome SEARCH BACK ISSUES of Nickel magazine from our online archive, going back to July 2002. www.nickelinstitute.org/en/NickelMagazine/ MagazineHome/AllArchives MOBILE Download the Nickel magazine app for your Apple® or Android™ device. FOLLOW US on Twitter @NickelInstitute JOIN US on LinkedIn—visit the Nickel Institute’s page WATCH nickel related videos on the Nickel Institute YouTube channel www.youtube.com/user/NickelInstitute

NICKEL IN BRIEF 15

A second freestanding structure includes the twelve curved glass sails wrapped around and above the iceberg, supported by a duplex stainless steel grid. The engineers selected 2205 duplex stainless steel (EN 1.4462, UNS S31803), with 4.5 to 6.5% nickel, for all inserts and nodes, the grid as well as for the gutters, braces, tension rods, thousands of bolts and hundreds of securing fasteners. It offers a yield strength twice that of a standard Type 316L (S31603), yet with 30% less weight. 1,500 tons of high strength duplex stainless steel support the majestic glass sails. In total the building structure contains 15,000 tons of steel—twice as much as in the Eiffel Tower.

reinforcing the sensation of sails and movement.

r C onverting an artistic/architectural vision into reality is a challenge—a challenge answered by engineers and nickelcontaining materials. L.M. DAUZAT

An outer structure comprises an intricate network of long-span laminated larch wood beams connected to carbon steel trusses. They constitute the solid suspension frame of the glass sails. From 3 to 35m long and in various curvatures, all these elements give the impression of gently swirling underneath the sails . A total of 540 duplex stainless steel inserts ensure firm connection between the wooden beams. In addition, 430 unique, geometrically complex nodes link all wooden and metal elements. Made from carbon steel/duplex stainless steel 100mm thick hybrid plates, they give the structure stability, allowing it to flex and maintain its integrity, while

he new Fondation Louis Vuitton museum inaugurated in Paris in October 2014, was born from a spontaneous sketch by Pritzker Prize-winning architect Frank Gehry, and a digital model created by the most advanced 3D software. The building clearly reflects Gehry’s disdain for the straight line. The result is a spectacular space with twelve monumental billowing glass sails supported by an entanglement of steel columns, wooden beams, transoms, braces and tension rods. All these elements are connected and draw upon the “iceberg”, a hard-shell structure containing the museum’s enclosed spaces.

FRANK GEHRY FONDATION LVMH 2014 TODD EBERLE

GLASS SAILS OVER PARIS