Western 26, December 19, 2021 by Construction Equipment Guide

$3.00

Published Nationally ®

Western Edition

December 19 2021 Vol. XXII • No. 26

“The Nation’s Best Read Construction Newspaper… Founded 1957.” 470 Maryland Drive • Ft. Washington, PA 19034 • 215-885-2900 • Toll Free 800-523-2200 • www.constructionequipmentguide.com

Inside

Point of Conflict Allen Butler Construction Corrects Trouble Spot in Lubbock, Texas Texas’ oil and gas industry supports millions of jobs statewide while its thriving windfarm industry employs tens of thousands of Texans. In fact, it’s been reported that if Texas were a country, it would rank number 5 in the world in total wind energy generation. Then there’s the state’s leading cash crop: cotton, a $5.2 billion industry that represents 40 percent of total cotton production in the United States. These three industries have a huge presence throughout the South Plains and Permian Basin areas in western Texas. So much so that traffic safety and mobility issues along heavily trafficked thoroughfares and at busy intersections are being aggressively addressed by the Texas Department of Transportation (TxDOT). One example: the U.S. 87/Farm to Market (FM) 41 intersection, where a 3-year construction project began in October. “Over the past few years, as more folks moved into southern Lubbock County and northern Lynn County, both U.S. 87 and FM 41 have seen an increase in traffic and, unfortunately, a rise in crashes at the intersection,” Steve Sisneros, TxDOT’s Brownfield area engineer, said. “The new bridge, a grade separation structure — always an improvement to any intersection — will eliminate the conflict point between the U.S. 87 mainlane traffic and FM 41 traffic. Also, the slower minor road FM 41 traffic will no longer have to travel across the high-speed U.S. 87 mainlanes, eliminating any stop-and-enter traffic and the related queuing issues.” Allen Butler Construction (ABC) Inc., a mid-sized heavy highway civil construction company in Lubbock founded in 1978 and known for its road and bridge infrastructure construction, is serving as the general contractor. ABC equipment being used for the U.S. 87 bridge project includes milling machines, scrapers, motor graders/maintainers, cranes, drill shafts,

By Joe Jancsurak Cater pillar Hosts Event to Showcase Cold Planers...8

Doosan Unveils New Dozer, Much Mor e in 2022...14

Flynn Brothers Inc. Relies On Rock Commander...38

CEG CORRESPONDENT

Allen Butler Construction Inc. crews demo a portion of the existing northbound U.S. 87 mainlane utilizing a John Deere 892 LC hydraulic excavator. The roadway’s frontage roads will be constructed during Phase 1 of the project.

belly-dumps and laydown paving machines. When finished, motorists will benefit from a new bridge that will take them over FM 41 as well as new entrance and exit ramps, turn-arounds and safety lighting, said Sisneros.How the three-phase project is approached has much to do with safety issues, Sisneros said. “The safety of the traveling public and construction crews is always our top priority, so for about eight months during Phase 1 of the project, FM 41 traffic will not have direct access to U.S. 87 and will be detoured see LUBBOCK page 64

Table of Contents ................4

Industry Ready to Dive Into Infrastructure Work

Paving Section..............25-37

As Agencies Assess Priorities, Contractors Prepare for Influx of Infrastructure Projects

Mini & Compact Equipment Section ..........................47-57 Auction Section ............62-65 Business Calendar ............64 Advertisers Index ..............66

By Lucy Perry CEG CORRESPONDENT

The ink is still drying on the Infrastructure Investment and Jobs Act (IIJA) as the construction industry awaits bid-letting and Congress turns to the reconciliation budget bill. After a long, hard-fought battle for funding, the industry is ready to get to work on these broad-spectrum infrastructure projects, which will color

the national construction picture for years to come. “America finally has a generation-defining infrastructure bill — and if the reconciliation budget comes through, too, America will begin a building spree larger than what happened during the New Deal,” observed Brookings Institution. It’s “worth pausing to consider” the enormity see INFRASTRUCTURE page 46

Page 2 • December 19, 2021 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • December 19, 2021 • Page 3

"In Business for over 33 Years" www.hendrixmachineryllc.com Se Habla Español

2007 Broderson IC80-2G, Stk#: 12945, 18,000 lbs., 46 ft., 1,147 hrs., 10 ft. JIB, 4WD, 4WS, 69 hp., 10.00Rx15 Tires ............................$21,500

2015 Dynapac CA1500, Stk#: 12526, EROPS, A/C & Heat, AM/FM Radio, 66" Smooth Drum, 267 hrs., 14.9x24R3 Tires, 4 Cyl. Deutz ..$69,500

2018 Cat D6N LGP, Stk#: 12876, EROPS, A/C & Heat, Radio, Sweeps, Rear Screens, 6 Way Blade, 3,647 hrs, 33" Pads, 13'4" Wide$179,500

2015 Bomag BW211D-50, Stk#: 12686, 84" Pad 2016 Cat CS54B, Stk#: 12900, OROPS, 84" Pad 2015 Cat 12M3, Stk#: 12898, EROPS, A/C & Drum, 2,026 hrs., 23.1x26R3 Tires, 4 Cyl. Deutz Drum, 2,428 hrs., S70x75x26R3 Tires, 4 Cyl. Cat Heat, Radio, 6,678 hrs., Front, Hyd., 14 ft. M/B, 2015 Freight Liner MZ, Stk#: 12874, 2,000 Gallons, 13,605 Miles, 11Rx22.5 Tires ..$52,500 Eng ........................................................$66,500 Eng.........................................................$89,500 Ripper, 17.5x25 Tires, 90% Tires ........$139,500

2018 Cat 259D3, Stk#: 12950, OROPS, 2,241 hrs., 6' 2" Bucket, 12" Tracks ................$42,500

2015 Bomag BW211D-50, Stk#: 12486, 84" Smooth Drum, 2,230 hrs., TR-387 Tires, 4 Cyl. Deutz Eng...............................................$59,500

2018 John Deere 850K WT, Stk#: 12931, 2012 Cat CT660S, Stk#: 12785, 2,980 hrs., EROPS, A/C & Heat, Radio, S/U Blade, 3,463 6x4WD, 4,000 gal. w/Front & Rear Spray Bars, hrs., 3 Shank Ripper, 30" Pads, 85% U/C, 10 ft. VIN: 1HSJGTKR6CJ062961 ..................$89,500 Wide ....................................................$198,500

2012 JLG 800S, Stk#: 12649, 1,000 lbs., 80 ft., 3,504 hrs., 4WD, 15x625 Tires @ 90%, 4 Cyl. Deutz Eng...............................................$39,500

2014 Cat 740B, Stk#: 12968, EROPS, A/C, 10,777 hrs., 29.5Rx25 Tires ..................$169,500

2016 Rome Disc, Stk#: 11856, 12' 32" Disc Tractor Attachment ................................$15,500

2013 Toyota 7FDV35, Stk#: 12809, 7,000 lbs., 2020 Trojan 35CL, Stk#: 12346, New Hydraulic 4,026 hrs., 48" Forks 48" Frame, 250-15/7.00 Hammer, Fits Cat 305, 305.5, 304, Case / Kobelco Front Tires, 7.00x12/5.00 Rear Tires, 6 Cyl. 2017 Cat 259D, Stk#: 12948, OROPS, 1,853 hrs., 72" Bucket, 12" Tracks ..................$42,500 35, Jdeere / Hitachi 35, Sany SY35 ........$3,850 Diesel Toyota Eng. ................................$12,500

2015 Cat 12M3, Stk#: 12898, EROPS, A/C & Heat, Radio, 6,678 hrs., Front, Hyd., 14 ft. M/B, Ripper, 17.5x25 Tires, 90% Tires ........$139,500

2018 Cat 259D3, Stk#: 12951, OROPS, 2,075 hrs., 74" Bucket, 14" Tracks ..................$42,500

2018 John Deere 850K WT, Stk#: 12931, EROPS, A/C & Heat, Radio, S/U Blade, 3,463 2003 Rome Disc, Stk#: 12157, 36" Disc ............ 2000 Cat 924F, Stk#: 12113, OROPS, 6,423 hrs., 3 Shank Ripper, 30" Pads, 85% U/C, 10 ft. ..............................................................$14,500 hrs., 94" Bucket, 17.5x25 Tires..............$29,500 Wide ....................................................$198,500

2010 Cat 120M, Stk#: 12838, EROPS, A/C & Heat, Radio, 8,378 hrs., 14 ft. M/B, Front Implement Attachment ........................$102,500

2015 Volvo SD115, Stk#: 12906, OROPS, 84" Vidratory Smooth Drum, 2,489 hrs., 90% Tires, 28.1x26Rx3 Tires, 6 Cyl. Volvo Eng ......$59,500

2015 Dynapac CA1500, Stk#: 12526, EROPS, 2018 Cat D6N LGP, Stk#: 12876, EROPS, A/C & A/C & Heat, AM/FM Radio, 66" Smooth Drum, Heat, Radio, Sweeps, Rear Screens, 6 Way Blade, 2019 Case 580N, Stk#: 12627, OROPS, 4WD, 267 hrs., 14.9x24R3 Tires, 4 Cyl. Deutz ..$69,500 3,647 hrs, 33" Pads, 13'4" Wide ............$179,500 865 hrs., 4&1 Front Bucket, Ext-hoe ......$78,500

2018 Cat 259D, Stk#: 12947, OROPS, 1,980 hrs., 74" Bucket, 14" Tracks ..................$42,500

2012 Genie S40, Stk#: 12106, 500 lbs., 40 ft., 3,307 hrs., 12x15.5 Foam-Filled Tires, 3 Cyl. Deutz Eng ..............................................$26,500

2010 Cat 120M, Stk#: 12838, EROPS, A/C & Heat, Radio, 8,378 hrs., 14 ft. M/B, Front Implement Attachment ........................$102,500

2009 Broderson IC80-2H, Stk#: 12449, 18,000 lbs., 46 ft., 1,066 hrs., 10 ft. JIB, 4WD, 4WS, 69 hp., 10.00Rx15 Tires ............................$21,500

2016 Cat CS54B, Stk#: 12900, OROPS, 84" Pad Drum, 2,428 hrs., S70x75x26R3 Tires, 4 Cyl. Cat Eng. ..........................................................$89,500

2019 Case 580N, Stk#: 12627, OROPS, 4WD, 865 hrs., 4&1 Front Bucket, Ext-hoe ......$78,500

2009 Broderson IC80-2H, Stk#: 12456, 18,000 lbs., 46 ft., 1,352 hrs., 10 ft. JIB, 4WD, 4WS, 69 hp., 10.00Rx15 Tires ............................$21,500

1-936-327-5430 • Email: sales@hendrixmachineryllc.com

2017 John Deere 750K LGP, Stk#: 12928, 2015 Volvo SD115, Stk#: 12906, OROPS, 84" EROPS, A/C & Heat, Radio, 6 Way Blade, 80% Vidratory Smooth Drum, 2,489 hrs., 90% Tires, U/C, 4,074 hrs., 34" Pads, 12 ft. Wide $142,500 28.1x26Rx3 Tires, 6 Cyl. Volvo Eng ......$59,500

2017 John Deere 750K LGP, Stk#: 12928, EROPS, A/C & Heat, Radio, 6 Way Blade, 80% U/C, 4,074 hrs., 34" Pads, 12 ft. Wide $142,500

Page 4 • December 19, 2021 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

CATERPILLAR HOSTS EVENT TO SHOWCASE ITS COLD PLANER MODELS

For dealers and contractors throughout the United States at the event, Caterpillar discussed its PM312, PM622 and PM825 cold planer models and provided several demonstrations of the PM825.

HITACHI SHIPS ITS FIRST ZX210LC-6 UTILITY EXCAVATOR

SOIL CONNECT NOW INCLUDES TIME TRACKING TO E-TICKETING

Hitachi Construction Machinery Americas Inc. announced the first medium-sized Hitachi ZX210LC-6 utility hydraulic excavator, built for the North American market, has shipped from Hitachi Construction Machinery Tsuchiura Works.

Doosan Infracore North America introduced its new products for 2022 during a media event at its Real Operations Center (ROC) in Arizona the first week of December.

During Season 3 of “Pave It Black,” NAPA’s podcast covering the people and issues affecting the industry, hosts Richard Willis and Brett Williams interviewed industry experts to dig deeper into the realm of asphalt.

DOOSAN UNVEILS NEW DD100 DOZER, MUCH MORE FOR 2022

VOLVO PROTOTYPE LX03: INTELLIGENT FUTURE OF CONSTRUCTION

The LX03, a fully autonomous, battery-electric prototype by Volvo Construction Equipment is the first real-world example of a self-learning concept wheel loader with the brains to make decisions, perform tasks and interact with humans.

CONTRACTOR DISCUSSES WHAT MAKES FOR SUCCESSFUL DREDGE

Dredging…what is it? Dredging, by definition, is the process of removing the sediment from a water body (reservoir or channel), transporting, and depositing it at another location far away.

WEEKS-LONG JOHN DEERE STRIKE ENDS AFTER NEW PACT

A five-week-long strike at John Deere ended as United Auto Workers (UAW) members approved a new six-year contract with the agricultural and construction equipment manufacturer.

KIRBY-SMITH MACHINERY’S DAVID MEHRTENS PASSES AWAY

David A. Mehrtens, 61, of Lenexa, Kan., passed away Dec. 3, 2021. He worked in the construction equipment industry for more than 40 years, most recently serving Kirby-Smith Machinery as director of remarketing and used equipment. Founder, Publisher & CEO Western Publisher Executive Publisher Editor In Chief Senior Editor Editorial Assistant Editorial Consultant Production Mgr. Controller Circulation Mgr.

Edwin M. McKeon Sr. Dennis Hogeboom Teddy McKeon Craig Mongeau Robby Chakler Katherine Petrik Pete Sigmund John Pinkerton Judith Nixon Cathy Printz

www.constructionequipmentguide.com

Facebook

Twitter

NAPA ‘PAVE IT BLACK’ PODCAST HIGHLIGHTS TECH INNOVATIONS BOMAG NAMES NEWEST VICE PRESIDENT OF MILLING, PAVING

SOOSAN’S ROCK COMMANDER GIVES FLYNN BROTHERS INC. CONFIDENCE

Flynn Brothers has used Soosan America’s Rock Commander rock drills for the majority of its drilling needs since 2018. The company currently has three Rock Commander drills in its fleet: a JD1400E-II and two JD800E-II drills.

INFRASTRUCTURE BILL CALLS ON INDUSTRY TO REQUIRE INNOVATION

The most aggressive infrastructure spending initiative since the 1950s was signed into law. Combined with a skilled labor shortage, the $550 billion bill calls into question whether contractors have the capacity to meet growing demand.

KIRBY-SMITH HIRES JOEL COOK AS EXECUTIVE VICE PRESIDENT, GM

Kirby-Smith Machinery (KSM) continues to build its executive team with the addition of Joel Cook as its new executive vice president and general manager, construction group.

FAMILY FUN DAY, FOOD DRIVE RAISE $4K FOR LOCAL FOOD BANK

Takeuchi-US employees, including President Jeff Stewart, presented the Banks Jackson Food Bank in Commerce, Ga., with food for 200 Thanksgiving dinners and an extra $2,550 to buy additional turkeys to feed more needy families.

RITCHIE BROS.: WHEEL LOADER PRICES UP 13 PERCENT IN NOV.

Ritchie Bros.’ November Market Trends Report continues to show positive pricing trends across all its equipment indexes, with medium earthmoving equipment prices up 36 percent in the United States.

MINI & COMPACT SECTION

52 54 56 56

HUMMERBEE MAKES IMPRESSION ON MICHIGAN EXCAVATOR CONTRACTOR CAT’S NEW 304, 305 CR INCREASE USER’S PERFORMANCE BOBCAT DEBUTS TWO REIMAGINED TOOLCAT UTILITY MACHINES

DITCH WITCH RT70 RIDE-ON TRENCHER MAXIMIZES OPERATOR EXPERIENCE TORO’S DINGO TX 700 COMPACT UTILITY LOADER IS IDEAL IN TIGHT SPACES

DEPARTMENTS

62 64

COMING AUCTIONS BUSINESS CALENDAR

DYNAPAC CC6200 VI Roller

EQUIPMENT

Dennis Hogeboom

Kent Hogeboom

Patrick Kiel

Sharon Swanson

• Colorado • Louisiana • Oklahoma • Texas • New Mexico

National Sales Manager

• Idaho • Montana • Oregon • Washington • Wyoming

• Arizona • California • Nevada • Utah

952/353-1770 612/481-8557 Cell e-mail pkiel@cegltd.com

760-518-4336 Cell e-mail sswanson@cegltd.com

Cell e-mail

Advertising e-mail production@cegltd.com

Mobile

For advertising rates Contact

Main office 470 Maryland Drive Fort Washington, PA 19034 215/885-2900 Toll Free 800/523-2200 Fax 215/885-2910 Web site

Circulated Throughout

• Alaska • Arizona • California • Colorado • Hawaii • Idaho • Montana • New Mexico • Nevada • Oklahoma • Oregon • Texas • Utah • Washington • Wyoming

To read these stories and many more, visit www.constructionequipmentguide.com

FEATURES

IN THIS ISSUE

WESTERN EDITION

YouTube

602/679-8759 dennishogeboom@cegltd.com

Cell e-mail

315/866-1423 518/221-5159 khogeboom@cegltd.com

Construction Equipment Guide Western Edition (ISSN 2330-9792) is published bi-weekly by Construction Equipment Guide Ltd. Advertising and Editorial Offices are located at 470 Maryland Dr., Ft. Washington, PA 19034. Toll Free 800/523-2200 or Fax 215/885-2910. Annual Subscription Rate $65.00. Call for Canadian and foreign rates.

the publisher. All editorial material, photographs, drawings, letters, and other material will be treated as unconditionally assigned for publication and copyright purposes and are subject to Construction Equipment Guide's unrestricted right to edit and comment editorially. Contributor articles do not necessarily reflect the policy or opinions of this publication.

Periodicals postage paid at Ft. Washington, PA and at additional mailing offices. POSTMASTER: Send address changes to Construction Equipment Guide Western Edition, 470 Maryland Dr, Ft. Washington, PA 19034.

Call or write for advertising rates, publication schedule and media kit. The Construction Equipment Guide is not responsible for clerical or printer's errors, every care is taken to avoid mistakes. Photographs of equipment used in advertisements are not necessarily actual photographs of the specific machine. Similar photographs are used occasionally and every effort is taken to depict the actual equipment advertised. The right is reserved to reject any advertising.

Contents Copyrighted ©2021, by Construction Equipment Guide, which is a Registered Trademark, registered in the U.S. Patent Office. Registration number 0957323. All rights reserved, nothing may be reprinted or reproduced (including framing) in whole or part without written permission from

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • December 19, 2021 • Page 5

563-8 872-44112 112

Bellevue (Dubuque), ubuque), Iowa sales@jjscheckel.com jscheckel.com

2015 CA ATT D11T - $1,285,000 $1,28 , 85,000

2002 CA ATT D11R - $185,000 $

2017 CA ATT D10T22 - $1,460,000

2005 CA ATT D10T D - $388,000 $

Zero Hour Powertrain Componen p ts w// 4 yyearr,, 6,000 hr 7PZ High g Horse series, Runs R andd oper p ates to spec p , 1,800 Hours, 525 at idle, dl 4 Year warranty w y remaining, RJG S#, 1 Owner since new n w,, Low L to midlif dl fe fe componen p t l d SS ipperr,, Good factoryy Cat warrantyy. U BBlade, S Rippe G UC. U-blade ipp r.. A/C, A//C /C, HHeat. Could U blade, Multi-shank ripper pppperr,, CCAT AT Minestar M GPS GPS, hours, SS ripper pp r,, U blade ade, Twin Twin tilt tilt, Well maintained, i i d bl d w// twin tilt, SSS ripper ld use Excellent hhistory,y, straight str i & clean. Availa b Jan. 2022. paint, otherwise very straight ilable i h tracttor from good home. Documentedd history, hi y, Reputa R ation i machine, Like new! Clean, straight, i h and repputable machine. Priced to sell.

RENT OR

2019 CA ATT D6 LGP - $35 $358,000 8,000 ,

Next Gen. A02947. 2,850 Hours, 2 Year ffulll warranty remainingg. ARO gr g ade assist, Multi shank ripper i r,, AAs clean l as they comee.

RENT OR

BUY!

2019 CA ATT D6T LGP VP PA AT - $288,000

2015 Deere ere 1050K - $328,000 $

4,650 hours, SUU Blade, B Multi Shank Ripper pp r,, Topc Topc p on GX60 Full Auto GPS syst y em comes withh machine. hi Straight, cleann & original i i Midwest dirt machine.

BUY!

2016 CA ATT D6T LLGP GP - $$288,000

2013 CA ATT D6 D6T 6T XW - $288,000 ,

2019 CA ATT 374FL - $618,000 A

A02962. 3,960 Total hours. 2 Year Yearr, 2,000 hour w warranty A02981. 2,161 Totall hhours, 695 at Idle, dl 1,466 actual A02952. 2,720 Hours, 744 Idle dl hours, h Only ly 1,976 3,663 Hours, 2 Years Years off ffactory fac y warrantyy remaining. i hi Grade control.l remainingg until 9/2023. ARP Accugr g ade GPS readyy,y, operatingg hours, Full 2 year ffactoryy warrantyy remains, actual oper p atingg hourss. GPS readyy,, AAllied W6G W Winch, Reputa p tion 1 owner o machine. Goodd U/C, documented hi history. Straight S i h bl blade, history since d documented history. 11’10” 0”” SStick. i k 4 Yar Yar a d 60”” bucket. buck Super clean machine! U/C Clean Cl and original with doc d RRear winch, i SService hi i new. VPPAAT 66-way blad bl de,

RENT OR

BUY!

2019 CA ATT 336 Next Gen - $$268,000 ,

2018 CA ATT 320 Next Gen Geen - $159,000 $ , 2018 CA ATT 320 Next Nexxt Gen - $$159,000 ,

2014 CA ATT MH3059 M - $348,000 ,

3,800 Hours, 1,367 Idle Idl hours, h W Warranty y untill 9/2023. / A02946. 2,623 totall hours, h 1,462 ooff those h hours h at idle, dl A02915. 2,450 Total hours, 1,593 IIdle hours. h 2DD Grade G d 8,250 Hours, Material handlerr,, as nice as they h y come. li cabb, 325 HPP,, 2D Grade contrrol ol. 12’10”” Stick S . 60”” Buck B ket. k 1 Ownerr,, 2D Grade Control, 9’6”” Stick, S Aux Hyydraulic Pkgg in stock. control, Deluxe pack p age g , Facctoryy warranty rremaining emaining. Ground access and hiigh g rise hydraulic Original paint, Documented history,y, Cle C ean machine! This machine won’t dissapoint, savve big $$ from new! 24”” BBucket S AAuxiliary li 35’ Boom, 29’ 9’’ SStick, i k Setup for k , 9’6” 9’66”” Stick, ili hydraulics. f grapple. 130,000 lbs.

(4)2016 ) Volvo A40G’s - $268,000 , EA. 55,400 400 Hour H truccks, Half idle time, Mat Ma ching h ggroupp. V y ggoodd Tailga g tes, 1 Ow wnerr,, Excellent Ex condition. Very R di tires. Ready to Radial t go. Rent/Lease or Buy. Buy

RENT OR

BUY!

(2)2015 ) Volvo V olvo A25G’s - $2448,000 48,000 EA. EA ((2)2014 ) CA ATT 730C’ 730C’s - $358,000 $$358 000 EA. EA 33,060 060 Hours, H 1,866 Idle hours, Tailgate il es, M Matching hi Radial tires, Original g pain p t, Documentted history,y, Volvo ddealer l iinspected, Very cleean.

Ejec Ej j tor bbodies, di 835 8 & 1,418 Hourrs. 1 Ownerr.. Radial R di l i Original tires. g pain p t. All maintenaance historyy. Super p clean, original, i l low l hour h trucks. Reent/Lease or Buy. B

B POWERTRAIN PLUS REBUILDS

ROLLERBLADES HOLMES SMOOTH DRUM R

2016 CA ATT 980M M - $268,000 $268,000

7,650 Hours, 2,671 in neutr utral,l Only ly 4,979 actual b k Ride R workingg hours. Radials, 7.5 Yar Yarrd GP buck bucket, control,l Auto A grease, Dealer maintained, History.

2019 V Volvo olvo L260H L - $288,000 ,

7,320 Hours, 2,333 2 333 Id Idle d hours, dl h 9.5 Yar Yarrd GP bucket, buck Ride contrrol ol, 875 Raddial tires, Dealer maintained, Documentedd history, Super clean.

2018 V Voolvo L180H - $238,000

A02916. 6,2500 Hours, H 6.5 Yar Yardd GP bucket b k , 330 HPP,, 62,000 lbs, Auxiillaryy hydaulic controls, Volvo dealer inspected. Clean andd straight, original machine.

RENT OR

BUY!

NEW! Ready to ship!

2014 K-TEC TEC 1233 - $148,000 , 2007 CA ATT 826H H - $$288,000 , 2011 CA ATT 140 140M 0M VHP - $248,000 248,000 , 36 Yar Yardd capacit p y pullll scraper p r,, very v y nice & clean. l CComes 9,800 Hours on Complet pl e Dealer l Rebuild R b ld. Goodd used Verified 735 total hours, 451 Idl dle hhours, Only ly 284 2 Models, 11’’ or 16’’ cuttingg width. Made in Iowa. 2006 CA ATT D10T Rebuild In n Process Constr with i h joyystick for Volvo V l A40. A40 i k conntrols, l hharness & hitchh for i tennance & servici e hist compac p tor w// ffullll main hi ory. i ide d actuall workking hours h . From state DOTT,, SStoree inside. uction ggrade d , extreme dduty. For haul h l roadd & site - $885,000. Zero hour Powertrain Plus, E i d 1,,400 hours use. Rear push block. Estimated EExcellen e , Cllean cabb, Testedd to OEM specs. ll t feet 14’ M Moldboard ldb d, M Mid id-m fi V Ripperr.. Tier 3. d mount Scarafier lleveling l , compacting & sealing l dir ddi t prior to rain event. Holmes 11F - $25,50 , 0 / 16F - $31,500 $

OEM CAT Warranty. New undercarraigge g , U Blade, i SS Ripperr,, Pre-emissions! Available M March/2021

visit

JJSccheckel.com

and w watch our new company vid deo!

The fastest growing w choice for

Large Equipm ment Rental

Delivered Nationwide.. We are easy to work with & will not be beat at on price and terms! Large Dozers - Cat D8T,T, D9TT,, D10TT,, D11T Large Excavators - Cat 374FL, L, 390FL Truck Fleet - Cat 740/745, & Volvo A40G Compaction, Wheel Loaderss, and much more.

WE OWN WHA ATT WE W ADVERTISE!

call: 5663 63-872-4112 872 4112 | email: sales@ @jjscheckel com | www. jjsscheckel.com @jjscheckel.com scheckel com | follow us ffor orr daily updates:

Page 6 • December 19, 2021 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

Compa act d Wh l d Tra k d

C805 | C807s | C810s C810 C815 C912

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • December 19, 2021 • Page 7

#92948, 2017 BOMAG BW138AC-5, 1200 HOURS ....................................................$39,500

#93105, 2017 BOBCAT E85, HYD THUMB, 1575 HOURS ..........................................$84,500

#83217, 2015 KOMATSU PC228USLC-10, 2850 HOURS ........................................$159,500

#2021001DM, 2015 KOMATSU D39PX-23, 2400 HOURS............................................$85,000

#92881, 2013 KOMATSU PC390LC-10, 7900 HOURS ........................................$119,500

#92729, 2012 KOMATSU WA380-7, JRB QC. 4000 HOURS..........................................$127,000

#83398, 2014 KOMATSU PC210LC-10, QC, 4200 HOURS ..................................................$104,500

#82380, 2009 KOMATSU PC220 LONG FRONT, 5,950 HOURS ........................................$129,500

#92930, 2011 KOMATSU D51PX-22, 6 WAY BLADE, 3200 HOURS ..........................$127,500

#52030, 2016 KOMATSU PC490LC-11, AUX HYD, #92926, 2013 KOMATSU PC490LC-10, 8750 JRB QC, 5700 HOURS ..........................$192,000 HOURS, AUX HYD, QC ..........................$109,000

#93009, 2015 KOMATSU PC240LC-10, 7,750 HOURS, QC ............................................$79,500

#80768, PC300LC-7 LONG FRONT, 7400 HOURS ................................................................$99,000

#92180, 2012 KOMATSU D65EX-17, RIPPER, SIGMA BLADE, 4700 HOURS ................$149,500

#92983, 2013 KOMATSU D65WX-16, CAB/AC, RIPPER, SIGMA, 6700 HOURS ..............$94,500

#93089,2020 TAKEUCHI TB290, AUX HYD, HYD THUMB, 455 HOURS ............................$104,500

Page 8 • December 19, 2021 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

Attendees look over and learn about the Cat PM825.

Travis McClung (L) of Caterpillar goes over the PM825’s ease of operation with Joe Neilso of B. Jackson Construction in West Jordan, Utah.

Travis’s larger-than-life personality, sense of humor and incredible spirit for life engaged the audience from the moment he took center stage.

Caterpillar Hosts Event to Showcase Its Cold Planer Models

aterpillar held an event Dec. 1, 2021, in Clayton, N.C., to showcase its lineup of cold planers.

Before the equipment walk-arounds and demonstrations began, however, retired United States Army Staff Sergeant Travis Mills of the 82nd Airborne delivered a keynote address to all attendees. Mills’s larger-than-life personality, sense of humor and incredible spirit for life engaged the attendees from the moment he took center stage. Mills is a recalibrated warrior, motivational speaker, actor, author and an advocate for veterans and amputees. Mills’s New York Times bestselling memoir, “Tough as They Come,” is currently available on sale in bookstores everywhere. Despite losing portions of both arms and legs from an IED while on active duty in Afghanistan, Mills continues to overcome life’s challenges, breaking physical barriers and defying odds. Mills lives by his motto: “Never give up. Never quit.” After his address, the equipment then took center stage. Five years ago, Cat brought a fresh roster of cold planers to the market and has been continuously working on improvements to the product line ever since. The 2021 product release marks the third update to these models since they were first introduced. For dealers and contractors throughout the United States at the event, Caterpillar discussed its

Caterpillar dealers and contractors from across the United States gathered in Clayton, N.C., to learn about the manufacturer’s line of cold planers.

PM312, PM622 and PM825 cold planer models and provided several demonstrations of the PM825. The PM312 is an efficient, highly maneuverable milling machine with a cutting width of 48.2 in. (1,225 mm) that performs controlled full-depth removal of asphalt and concrete pavements in a single pass. The PM622 is a high-production, half-lane milling machine with a cutting width of 88 in. (2,235 mm) that performs controlled full-depth removal of asphalt and concrete pavements in a single pass. The PM825 is a high-production, half-lane milling machine with a cutting width of 98.6 in. (2,505 mm) that performs controlled full-depth removal of asphalt and concrete pavements in a single pass. The models meet U.S. EPA Tier IV Final, EU Stage V and Korea Tier 4 Final emissions standards and are optimized to reduce fuel burn with a high-capacity cooling system that keeps the engine at ideal temperatures for optimal fuel efficiency and lower emissions. New expanded LED lighting enhances nighttime and low-light operation. The new wide-dispersion LED work lights come standard and provide an improved, well-lit work area for ground crew. LED perimeter lights also can be added to further illuminate the rotor chamber, cutting path and work areas around the machine for increased visibility. According to Cat, the integrated Cat GRADE with Grade and Slope system takes the guesswork out of producing accurate and repeatable cutting results and includes automated features like obstacle jump and programmable cut transitions to aid in milling precision. Cat cold planers also can be enhanced with full 3D milling operation. The cutting system is designed to withstand tough applications and is built to last with heavy steel construction and reinforced alloys to resist abrasion, according to Cat. Available in a wide variety of spacings, the durable Cat System K rotors deliver high-performance with efficient material flow and an excellent cutting pattern. Kicker paddles are reversible for extended life, and the tapered dual retention toolholder design eliminates the need for retaining bolts, pins, or setscrews, reducing replacement time by up to

50. A reliable track undercarriage system with well-engineered track geometry provides high tractive effort and better load distribution when milling deep cuts or through hard materials. High-capacity conveyors provide efficient removal of milled material with outstanding discharge control. The belt also reverses for faster clean-up, while magnetic vinyl covers provide quick access to inspect the rollers for wear. Optional dust ventilation and spray bar systems maximize dust removal. Longer lasting conveyor flashing, improved rotor drive access, corded pendant for the rotor turning device and an added wear shoe for the inboard ski are just a handful of the many improvements included in this product update. Cat milling machines are designed with long maintenance intervals, large service doors, and power hood for walk-in access to critical components and systems. Track pads are easy to replace, while track chains and other undercarriage components are maintenance-free up to 4,000 hours. When time to replace high wear components, Cat dealers provide specialized support with repair kits, convenient parts availability, and service options for both the machine and the engine.  CEG

The Cat PM825 is a high-production, half-lane milling machine with a cutting width of 98.6 in. (2,505 mm) that performs controlled full-depth removal of asphalt and concrete pavements in a single pass.

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • December 19, 2021 • Page 9

MADE FO OR

AMERIC CA SERVIC CE THAT’S TS

LOCAL L SCHEDULE A DEMO O

TODAY Y WITH A LOCAL DEA ALER

Award Winning

SW405K

Page 10 • December 19, 2021 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

Hitachi Ships Its First ZX210LC-6 Utility Excavator

Transfor o ming your excavator. And your business. The Rototilt® tiltrotator transforms your excavator into a flexible tool carrier. This opens the way for new t ypes of jobs, and ma ximize both safet y and productivit y. The whole tiltrotator fami m ly is packed with innovative technolo o gies and ingenious design solutions that make your work safer, easier and more profitable. Like our safet y solution SecureLock™, and the time-saving QuickChange™ that lets you change hydraulic work tools without leaving the cab. With Rototilt® you get a tiltrotator that fits your specific need, whether you require dex terit y and precision, or muscles and capacit y. Rototilt® makes it possible.

Open-S The open n industry standard for fully a automatic quick couplers. Read mor o e at www.opens.org

rototilt.com

Hitachi Construction Machinery Americas Inc. (HCMA) announced that the first medium-sized Hitachi ZX210LC-6 utility hydraulic excavator, built for the North American market, has shipped from Hitachi Construction Machinery Tsuchiura Works (Tsuchiura, Ibaraki Prefecture, Japan). The ZX210LC-6 excavator is the first of many Hitachibuilt and branded machines soon to be available throughout North America and Latin America, according to the manufacturer. With the joint venture dissolution between Hitachi Construction Machinery Group and Deere & Company, announced earlier this year, HCMA is committed to independently developing and deploying the latest product advancements, technologies and services throughout the region. To celebrate this important milestone for Hitachi and its customers, the team in Japan responsible for developing and building this first excavator unit gathered to give it a proper sendoff. Draped across the machine is a banner with the phrase “Empowering the Americas — The Lineup Grows More Powerful.” This message signifies HCMA’s commitment to its customers moving into the future. Since 1965, with the introduction of the Hitachi UH03, Japan’s first hydraulic excavator, Hitachi hydraulic excavators have been a flagship product of the Hitachi Construction Machinery portfolio. With a range of models available to meet customers’ specific requirements, these machines excel at leveling and forming work for large-scale residential land and the development of social infrastructure for roads, railways and riverways. Hitachi utility excavators available in the Americas, including the ZX210LC-6 model, are equipped with Solution Linkage Assist, a proprietary machine control feature, which enables efficient work to be performed without over-excavating the target work surface, as well as a hydraulic system that features high-efficiency AERIAL ANGLE technology to help improve worksite safety and the brand’s ConSite OIL service solution. These machines are designed to help contractors in the Americas maintain the quality of work amid labor shortages and the decline in experienced operators, as well as to contribute to improved productivity and safe operation. Local sales for the latest Hitachi-built line of equipment will start in North America in March 2022. For more information, visit www.hitachicm.us. 

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • December 19, 2021 • Page 11

PLEASE CONTACT YOUR LOCAL DEALER: ALASKA

TEXAS

ARIZONA

CALIFORNIA

COLORADO

IDAHO

OKLAHOMA

OREGON

¡ ¢

¡ ¢ £ ¡ ¢

UTAH

WASHINGTON

WYOMING

NPK MANUFACTURES AND MARKETS THE GREATEST SELECTION OF:

NPKCE.COM

Page 12 • December 19, 2021 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

Ed McKeon

Judy Nixon

Craig Mongeau

Ted McKeon

Theresa Vickers

Rob Chakler

Joe McKeon

Katherine Petrik

Richard McKeon

Mia Klimp

Barry McKeon

Sondra Rossi

Teddy McKeon Kent Hogeboom

Cathy Printz

Rich Olivier

Martine Matteo

Ed Bryden

Caitlin Murphy

Patrick Kiel

Anne Shoemaker

Dennis Hogeboom

Deby Hogeboom

Maria McKeon

Joshua Phillips

Denise Giaccio

Donna Prendergast

Sharon Swanson

Mary DeRosa Rob Tredinnick John Pinkerton

Andrea Pinkerton

Matt Seslow

Stephen Collins

Jennifer Hood

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • December 19, 2021 • Page 13

Page 14 • December 19, 2021 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

Doosan Unveils New DD100 Dozer, Much More for 2022 Doosan Infracore North America introduced its new products for 2022 during a media event at its Real Operations Center (ROC) in Arizona the first week of December. The company’s next generation crawler excavators, miniexcavators and new -7 series wheel loaders were featured in presentations by the respective product specialists. Doosan also unveiled its DD100 dozer, which it said will be available through dealers in 2022. Technological upgrades also were introduced, including the “Transparent Bucket.” The transparent bucket is a system that allows the wheel loader operator to see blind spots in front of the bucket through the monitor in the cockpit. The innovative system records images in front of the wheel loader with cameras installed at the top and bottom of the equipment and shows combined images in real time using a curved projection method. The front of the wheel loader has been considered an area prone to major safety issues due to its blind spots. With the transparent bucket function, however, the operator can easily check the blind spot in front of the bucket through the monitor and prevent accidents. Another advantage is that it can significantly improve work efficiency by enabling a forward-view perspective during loading/unloading or when carrying soil and sand, according to the manufacturer. DD100 Dozer Doosan’s 122-hp DD100 dozer delivers powerful pushing performance, fuel efficiency and all-day operator comfort, according to the manufacturer. The DD100 features a dual/single flange-type roller with several track guard options. Designed with operators in mind, the DD100 features the 8-in. Smart Touch display, giving operators complete control from a convenient, easy-to-read touch screen. It also offers enhanced visibility with minimized front pillars, maximum glass area and a standard rearview camera — plus LED lights and front, rear and side wiper blades. The DD100 features a Doosan engine with convenient maintenance access points and does not require the use of a diesel particulate filter to meet current emission standards. Doosan DD100 owners can add the 3D Machine Guidance

Doosan unveiled its DD100 dozer, which will be available through dealers in 2022.

and 3D Machine Control features as an option for greater accuracy and ease of operation. Specs include: • Horsepower: 122 hp • Operating Weight: 25,309 lbs. • Blade Capacity: 3 cu. yds. • Blade Height: 3 ft. 7 in. • Blade Width: 8 ft. 10 in. • Blade Angle: 22.5 degrees • Drawbar Pull: 33,721 lbf. • Track Length: 7 ft. 7 in. • Travel Speed, max: 5.7 mph (Preliminary specs, subject to change) Other Unveilings During the event, Doosan also announced several other new equipment models coming to the North American market in 2022.

DX27Z-7 Mini-Excavator Specs include: • Horsepower: 24.7 hp • Operating Weight: 6,168 lbs. • Maximum Digging depth: 8 ft. 8 in. • Maximum Digging Reach (ground): 14 ft. 10 in. • Maximum Loading Height: 10 ft. 1 in. DX35Z-7 Mini-Excavator Specs include: • Horsepower: 24.7 hp • Operating Weight: 8,807 lbs. • Maximum Digging Depth: 11 ft. 4 in. • Maximum Digging Reach (ground): 17 ft. 9 in. • Maximum loading height: 12 ft. 2 in.

Doosan unveiled three mini-excavators: the DX27Z-7 mini-excavator, the DX35Z-7 mini-excavator and the DX50Z-7 mini-excavator.

see DOOSAN page 60

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • December 19, 2021 • Page 15

Page 16 • December 19, 2021 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

Volvo Prototype LX03: Intelligent Future of Construction The LX03, a fully autonomous, battery-electric prototype by Volvo Construction Equipment (Volvo CE) is the first real-world example of a self-learning concept wheel loader with the brains to make decisions, perform tasks and interact with humans. It also is the first time ever a LEGO Technic model has been turned into a real machine. While not commercially available, engineers expect that valuable insights from the LX03 will feed into applications for today and tomorrow. Inspired by a concept devised by Volvo CE and LEGO Technic engineers and designers, the Volvo LX03 is a remarkable milestone breaking new grounds in smart construction technology. It represents both the next stage in Volvo CE’s exploration into machine intelligence and its determination to decarbonize the construction industry. Melker Jernberg, president of Volvo CE, said, “We need to transform the construction industry with

smart and more sustainable solutions that will have an impact on a global scale. The unveiling of the LX03 prototype today represents just that — and is testament to the incredible expertise of our engineers and our united commitment towards positive change. Together with the LEGO Group, we are pushing the boundaries of both technology and imagination and the result is beyond anything the world has seen before.” Lars Stenqvist, chief technology officer of Volvo Group, said, “As transport and infrastructure leaders, we have a vital role to play in taking action on climate change and stepping up the pace of innovation needed to deliver on emissions targets. We believe in working with driven and creative partners who, like us, are focused on making innovation real and moving beyond just words.” Pioneering Partnership What started out as an exciting project between designers and engineers at the two companies, to

explore the potential for future construction, evolved over time with the help of a team of smart children into the successful launch of the 42081 LEGO Technic Concept Wheel Loader ZEUX. The LEGO Group’s Head of Product for LEGO Technic, Niels Henrik Horsted said, “Our two companies have enjoyed an extremely successful partnership

over the years in which we have collaborated on several LEGO Technic models. But this is the first time we are making a real machine based on a model and not the other way around — and that is what makes this a truly unique project.” Collaborative Machines The prototype LX03 has been built by a dedicated team of engi-

The prototype LX03 with the LEGO Technic Concept Wheel Loader ZEUX, which inspired its creation.

neers, programmers and workshop technicians from Volvo CE sites in Eskilstuna, Sweden and Konz, Germany, in collaboration with the design team in Gothenburg, Sweden. It is a 5-ton wheel loader that has been developed as a modular concept, with the capability of being made larger or smaller with just one or two changes to the manufacturing process. It also shares its driveline with the L25 Electric, making it a zero emission, lownoise machine with a runtime of up to eight hours depending on its application. It is designed to be a smart and safe worker, equipped with a brain that has the capacity to adapt to different scenarios, make decisions in real-time and most importantly collaborate with humans. It can be programmed by customers to complete heavy, repetitive or dangerous tasks, reducing the need for a human on site. For more information visit, https://www.volvoce.com/global/e n/this-is-volvo-ce/what-webelieve-in/innovation/zeux/. 

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • December 19, 2021 • Page 17

Committed to bringing our customers the best in sales, parts and service. “We are very excited to add Tri-State Equipment to the Hyundai Construction Equipment network of dealers. With their extensive coverage and aggressive customer-first approach, Tri- State Equipment is the right partner to help us grow the Hyundai brand.”

COMPACT EQUIPMENT HYUNDAI DEALER Hyundai Construction Equipment Americas announces the expansion of its North American authorized dealer network with the addition of Tri-State Equipment Rentals. Tri-State has been providing top quality Construction Equipment in the Southwest since 2007. Every member of the Tri-State team works to provide the highest quality machines and service. With the addition of this new dealership in Arizona, Hyundai’s North American network now includes over 80 dealerships operating in just over 180 locations, offering sales, service, and parts for the full line of Hyundai excavators, wheel loaders, compaction rollers and other construction equipment.

- Matt Brown, HCEA District Manager –West “We are excited to supply our customers here in the Tri State area with a quality manufacture like Hyundai Construction Equipment.” - Robert Lara, VP/General Sales Manager

For more information,

928-704-0101 4095 Hwy 95 Fort Mohave, AZ 86426

928-680-6748 82 N. Lake Havasu Ave Lake Havasu City, AZ 86403 tristate-hyundai.com

Fort Mohave, AZ

Lake Havasu City, AZ

www.hceamericas.com

Page 18 • December 19, 2021 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

Contractor Discusses What Qualities Weeks-Long John Make for Highly Successful Dredge Deere Strike Ends After New Pact The new agreement will boost hourly wages by 10 percent and increase retirement benefits. When Gerke Excavating needed a highly powered customized cutter head dredge, it turned to DSC Dredge.

Dredging…what is it? Dredging, by definition, is the process of removing the sediment from a water body (reservoir or channel), transporting, and depositing it at another location far away. For some, dredging is undertaken for a variety of reasons, including mining, navigation, environmental remediation, flood control and the emplacement of structures (e.g., foundations, pipelines and tunnels). The question now is what makes a company or service a success story when it comes to dredging — is it only the equipment, or does it extend further? According to Taylor Hancock, quarry organizations supervisor of Gerke Excavating Inc., “It’s the ability to provide quality service while building long standing relations,” goals that her family’s company has stood on since 1946. Gerke Excavating, located in Tomah, Wis., offers services that include not only excavating, site grading and trucking, but also crushing and decades of experience in various mining techniques. So, after much industry research, this familyowned business made the decision to purchase a customized dredge from DSC Dredge. Wayne McGinnis, mining operations supervisor of Gerke Excavating Inc. said, “After speaking with Charles Johnson, DSC’s director of domestic dredge sales, I knew immediately that DSC was the right choice. “Throughout the entire process I never felt like I was a bother, or asking too many questions. He was always accessible, and his response time was exactly the way we would operate with our clients — it felt like home.” DSC Dredge is a family-owned dredge manufacturing company based in Reserve, La., whose customized technology and dredging solutions lead the industry throughout 50 different countries, according to the company. While Gerke was no stranger to dredges, it was made clear that the current dredge they were utilizing just wasn’t cutting it. The materials they were attempting to liberate were too hard and required a highly powered customized cutter head dredge. Specifically, a Custom 10300 Series Electric Marlin Dredge with Digging Jet, which includes DSC’s highly innovative, user-friendly bottom visualization system, DSC VISION. According to McGinnis, “DSC Vision has been a phenomenal system, it is very helpful for the operators and has

exceeded all expectations. The software is incomparable to anything else we have ever utilized. “The entire process, from delivery to set up and support has been phenomenal,” said McGinnis, noting that from the beginning his team was made to feel like family, not just another customer. “To know I can pick up the phone and call Bill [DSC’s coowner, EVP of product development and CTO[ and get immediate feedback is a great feeling.” Hancock echoed similar sentiments. “Throughout my own family, across all generations, starting with my great grandpa Allan who started the company and then through my dad, it was always taught, ‘you have to take care of your customers and community’ and this is the feeling I get every time we interact with DSC. The feeling of continuous support; that we have nothing to worry about.” She recalled how much it meant to everyone when Bill Wetta came out to their site to just “check in” on their jobs. That personal touch demonstrated that DSC cared not just about the delivered dredge and its performance, but also about the Gerke team and their own success, she said. “To know there are other companies out there that value their clients the way we do means a lot. It showed us everyone has boots on the ground and are ready to interact. The experience of the two teams working together — DSC’s product support guys and our dredge operators, was so positive that it was honestly one of the best experiences we’ve had.” Gerke Excavating has a strong foundation with well over three decades of experience mining limestone and over a decade with frac sand. While they have been dredging for six years, future expansion is already being discussed. “DSC values our partnership with the Gerke family. As they have shared, our business models are very similar, and our values are aligned which made this a win-win relationship all around. We are excited to be a part Gerke’s continued growth in the dredging industry,” said William J. Wetta, DSC Dredge. DSC Dredge operates from three manufacturing facilities located in Reserve, La., Poplarville, Miss., and Greenbush, Mich. For more information, visit www.dscdredge.com. 

A five-week-long strike at John Deere ended Nov. 17 as United Auto Workers (UAW) members approved a new sixyear contract with the agricultural and construction equipment manufacturer. The new agreement will boost hourly wages by 10 percent and increase retirement benefits. In addition, the company will maintain its health insurance program, in which workers do not pay premiums, the Register reported. The pact was approved by approximately 61 percent of UAW voters. The 10,100 John Deere workers in Iowa, Illinois and Kansas had rejected two previous contracts, setting off the first strike against the company since 1986. “UAW John Deere members did not just unite themselves,” Ray Curry, president of UAW International, said in a statement. “They seemed to unite the nation in a struggle for fairness in the workplace. We could not be more proud.” In his own statement, Deere CEO John May said, “I’m pleased our highly skilled employees are back to work building and supporting the industry-leading products which make our customers more profitable and sustainable.” Deal Reached On Third Contract Proposal The contract approved Nov. 17 was much the same as an agreement that 55 percent of members voted down Nov. 2. After that vote, company officials said they would not offer any further wage or benefit increases. The strike began as Deere celebrated the prospect of record profits, with executives projecting in August that the company would earn $5.7 billion-$5.9 billion for the fiscal year that ended Nov. 1 — a 62 percent bump over 2013 earnings, the company’s previous record year. In the first contract introduced in early October, Deere offered up to 6 percent pay increases and re-introduced quarterly cost-of-living adjustments, a feature of previous Deere-UAW contracts that the company eliminated in 2015. The equipment maker also offered workers $3,500 bonuses if they ratified the contract. Additionally, the company proposed a boost to the pension program that would have given a 25-year employee about $100 extra each month in retirement and offered lumpsum payments of $20,000 to $50,000 for workers when they retire, depending on their length of service. At the same time, Deere proposed to eliminate the pension program for workers hired after Nov. 1. 

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • December 19, 2021 • Page 19

Page 20 • December 19, 2021 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

7TFI <NIJSJWX

2FYJWNFQ 9WFSXKJW ;JMNHQJX

10’ Commercial Pavers ѣ (TRRJWNHFQ 5F[JWX

<NYM T[JW ^JFWX TK J]UJWNJSHJ \J XUJHNFQN_J NS GZ^NSL FSI XJQQNSL ZXJI FXUMFQY UF[NSL JVZNURJSY

8’ Commercial Pavers ѣ (TRRJWNHFQ 5F[JWX

9FSIJR ;NGWFYTW^ 7TQQJWX

WEPIW$GEPZMRKVSYTMRG GSQ \\\ HFQ[NSLWTZUNSH HTR

&XUMFQY )NXYWNGZYTWX

(MNU 8UWJFIJWX

2NQQNSL 2FHMNSJX

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • December 19, 2021 • Page 21

WE HAVE YOUR NEXT OFF ROAD TRUCK Niece 8,000 gallon water tanks installed on 40 ton Articulated Off Highway chassis. This combination is the workhorse of the dust control and water needs for quarries and large construction sites

NWT9500

The NWT9500 950 Gallon water tank mounted on articulated truck. Pictured: Deere 460E with 9,500 gallon tank. Tanks come with 6X5 pumps.

NFL3000

The NFL3000 Off Road, Fuel and Lube Bed offers 3,000 gallons of diesel fuel.

NFL10000

The NFL10000 Fuel & Lube Can be mounted on any 100,000 lb rigid frame truck. Holds 10,000 gallons of diesel. 5 additional fluid tanks. Holds up to 3,000 gallons of oil.

Page 22 • December 19, 2021 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

www.trophytractor.com Agricultural Tractors

Crawler Loaders

Off-Highway Trucks

Water Equipment - Trucks

2015 JOHN DEERE 6215R..................................................$139,500 (4) 2018/19 JOHN DEERE 6120M..............................From $79,500 2018 JOHN DEERE 5125R....................................................$98,500 (2) 2017 JOHN DEERE 5085M ..................................From $59,500

(3) 2017-20 CATERPILLAR 963K ............................From $265,000

(2) 1995 CATERPILLAR 777C ..............................................$59,500

2013 CATERPILLAR 740B ............................................................$329,500 (3) 2014/15 CATERPILLAR 725C ....................................From $269,500 2017 CATERPILLAR 725C2..........................................................$339,500 2021 CATERPILLAR 725................................................................$550,000 2019 FORD F750 ................................................................................$95,000 (2) 2007/15 FREIGHTLINER M2 ........................................From $49,500 (18) 2018-20 KENWORTH T370 ................................From $89,500 (18) 2018-22 PETERBILT 348 ..................................From $119,500 VOLVO A25D..........................................................................$109,500

Artic Trucks (2) 2016 CATERPILLAR 745C......................................$309,500 Ea. (2) 2019 CATERPILLAR 745 ........................................$465,000 Ea. (5) 2016-2019 CATERPILLAR 725C2......................From $259,500 (2) 2014-15 CATERPILLAR 725C ............................From $195,000

Compactors - Padfoot/Smooth Drum 2020 CATERPILLAR 815K......................................................$CALL 2007 CATERPILLAR 815F 2 ..................................................$CALL (4) 2013-17 CATERPILLAR CS66B ........................From $129,500 (6) 2013-18 CATERPILLAR CP56B ........................From $129,500 (4) 2017/18 CATERPILLAR CS56B ..........................From $64,500 2019 HAMM H7IP....................................................................$69,500

Crawler Carriers 2019 MOROOKA MST4000VD............................................$319,500 (2) 2018 MOROOKA MST3000VD ..........................From $229,500 (3) 2018/19 MOROOKA MST2200VD......................From $172,500 (2) 2019 MOROOKA MST1500VD ..........................From $149,500 MOROOKA MST660VD..........................................................$89,500

Dozers - Crawler

Motor Graders

2012 CATERPILLAR D11T......................................................$CALL 2017 CATERPILLAR D10T2, 3456 Hrs..............................$965,000 2018 CATERPILLAR D9T ....................................................$829,500 (4) 2018 CATERPILLAR D8T....................................From $510,000 2020 CATERPILLAR D6 XL ................................................$425,000 (6) 2019-21 CATERPILLAR D6 LGP........................From $425,000 (4) 2014-19 CATERPILLAR D6T XW ......................From $159,500 2016 CATERPILLAR D6N LGP ..........................................$139,500 2018 CATERPILLAR D6K 2XL............................................$185,000 2012 CATERPILLAR D6K XL ................................................$CALL

2020 CATERPILLAR 150AWD............................................$407,500 (2) 2017-19 CATERPILLAR 140M3........................................$CALL 2019 CATERPILLAR 16M3..................................................$845,000 2016 CATERPILLAR 14M VHP ..........................................$405,000 2007 CATERPILLAR 14H ....................................................$155,000

Dozers - Wheel 2015 CATERPILLAR 834K ..................................................$285,000

Excavators - Crawlers 2015 CATERPILLAR 374FL ................................................$395,000 (2) 2017/21 CATERPILLAR 349FL ..........................From $329,500 2019 CATERPILLAR 336 ....................................................$289,500 2017 CATERPILLAR 336FL, 2941 Hrs ..............................$219,500 2014 CATERPILLAR 329EL, 4134 Hrs ..............................$159,500 2015 CATERPILLAR 323FL ................................................$132,500 (2) 2018/19 CATERPILLAR 320 ..............................From $179,500 2017 CATERPILLAR 316FL ................................................$169,500

Scrapers

Wheel Loaders

1980 CATERPILLAR 637D ....................................................$59,500 2000 CATERPILLAR 627F ..................................................$125,000

1991 CATERPILLAR 992C......................................................$CALL 2019 CATERPILLAR 982M..................................................$439,500 (2) 2018/2019 CATERPILLAR 966M........................From $329,500 (2) 2018 CATERPILLAR 938M ................................From $179,500 2015 CATERPILLAR 914K ....................................................$69,500

Skid Steers - Track (8) 2020-21 JOHN DEERE 333G............................................$CALL (3) 2020 CATERPILLAR 299D3 XPS ....................................$CALL (3) 2021 CATERPILLAR 299D3..............................................$CALL (4) 2015-18 CATERPILLAR 299D2 XPS ..................From $59,500 2016 CATERPILLAR 242D ....................................................$39,500

Water Equipment - Tower/Tanks

Miscelleneous Equipment 2021 ROME TRCW16 ..............................................................$CALL 2018 ROME TRCW12..............................................................$48,500 2019 ROME TACW16..............................................................$36,000 2018 ROME TCW28 ................................................................$19,750 2018 ROME TCW32 ................................................................$23,000

(4) 2020/21 Klein KPT-120 Water Towers..................From $54,500

Authorized dealer for

Winch PACCAR PA110VS245 ............................................................$7,500

Fisher Sand and Gravel Begins $52M Ariz. Bridge Project BULLHEAD CITY, Ariz. (AP) Siteclearing work has begun for a $52.4 million bridge construction project to provide a long-awaited second road crossing over the Colorado River between Bullhead City, Ariz., and Laughlin, Nev. Actual construction is expected to begin by the end of the year and is scheduled to be completed by the end of 2023. Fisher Sand and Gravel, of Tempe, Ariz., is the primary contractor for building the four-lane bridge that will span 724 ft. (221 m) and include a path for pedestrians and bicyclists. “Bottom line, the new bridge project is underway after many, many years of dialogue and debate,” said Bullhead City Manager Toby Cotter. “It's going to happen. It’s starting to happen now.” The project is a partnership between Bullhead City and Clark County, which includes Laughlin, an unincorporated casino and resort community. The two communities across the river from each other share a local economy, with many Bullhead City residents working in

Laughlin. “The need for a second bridge connecting Laughlin and Bullhead City has been discussed and planned for decades, with federal funding first committed in the 1990s,” said Clark County Commission Michael Naft, whose district includes Laughlin. “This bridge is an important transportation element and it is also critical for emergency responders.” The bridge will link the Bullhead Parkway in southern Bullhead City to Needles Highway in Laughlin, the Mohave Valley Daily News reported. The existing Laughlin Bridge, paid for by Laughlin founder Don Laughlin in 1987 and deeded to the states of Nevada and Arizona, has served since 2001 as the only span crossing the river within the Bullhead City limits. The new bridge will be about 8 mi. (13 km) south of the Laughlin Bridge and about 6 mi. (9.6 km) north of the Veteran’s Memorial Bridge linking Fort Mohave to Laughlin near the Avi Resort Casino. The next-closest bridge is at Needles. Before the Laughlin Bridge was built, the

bridge at Davis Dam was the only link between Bullhead City and Laughlin. That bridge was closed to public access following the 2001 terrorist attacks against New York and Washington, D.C. Work recently started with clearing brush

and other debris from the project area, constructing a pond near the Colorado River Nature Center on the Arizona side and staging equipment near the work site. Clark County is contributing $27.1 million, the federal government is providing $20.8 million and Bullhead City will pay

$4.5 million. The bridge has long been in the planning process, with then-U.S.-Sens. John McCain of Arizona and Harry Reid of Nevada pledging support well before the turn of the century and Bullhead City and Nevada officials working with the Federal Highway Administration to identify an appropriate site. The original favored site was discarded in 2008 because construction would have infringed on a public park, precluding federal funding. It then took Bullhead City several years to come up with its current preferred site. But Laughlin officials didn’t like the site, and said it was too far south of Laughlin's business and casino districts and that the location would require construction of a new roadway to connect the bridge to Needles Highway. At one point, the Laughlin Town Advisory Board asked if there were other projects of greater benefit to Laughlin that could benefit from county money earmarked for the bridge. 

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • December 19, 2021 • Page 23

RENTALS

HEAVY EQUIPMENT

Kirby-Smith Machinery’s David Mehrtens Passes Away

Serving the Construction & Mining Industries Since 1962

Former Rental Units for Sale:

David A. Mehrtens

David A. Mehrtens, 61, of Lenexa, Kan., passed away Dec. 3, 2021. He worked in the construction equipment industry for more than 40 years, most recently serving KirbySmith Machinery as its director of remarketing and used equipment.  Message from Ed Kirby, John Arapidis The entire Kirby-Smith family is still in mourning over the news last Friday regarding the passing of our dear friend and colleague David Mehrtens. Chairman of the Board Ed Kirby and President John Arapidis have prepared the following statement: As we mourn the loss of David Mehrtens, our sincerest condolences go out to his wife Robyn, his daughters, and the entire Mehrtens family in this difficult time. David had no trouble integrating himself into the Kirby-Smith family when he left Kansas for Oklahoma City to become our Director of Remarketing and Used Equipment in 2017. Indeed, he endeared himself to everyone he encountered and exemplified the best of our principles in his selflessness, honesty, loyalty, and friendship. David loved to teach others and had the gift

of making learning fun. He invested so much time into so many of us, and in doing so has established a strong foundation that will continue to shape Kirby-Smith Machinery long after his passing. As a professional, the impact David made on this company was both sizable and immediate. His wealth of experience at pricing and trades, along with a penchant for always finding the right equipment for customers, allowed him to gain the trust of our salesforce overnight. One of the most respected used equipment managers in the entire industry with a network of contacts second to none, David’s presence helped elevate our used equipment business to new heights. He was a great teammate who was passionate about selling equipment and helping others, and he continued to serve as a valuable resource and mentor into his final days. In closing, we reflect on how much David loved being a part of Kirby-Smith Machinery, and how much this company loved him for being here. Though we have all lost a good friend, we are incredibly fortunate to have had someone with the character and integrity of David Mehrtens in our lives, and he will be deeply missed. 

2001 CAT 320CL, Ready to work, 24T HEX 1996 CAT 815F, Excellent, work ready 22 ton with reach boom, med stick, cab, AC, aux soil compactor with OROPS, S-Dozer w/ tilt, hyd. QC, 1000 hrs on new tracks ......$55,000 5200 hrs on rebuilt engine, 0hrs on newly rebuilt trans and 1200hrs on feet ....$149,000

2003 CAT D6R DS LGP, Excellent, series 2, LGP w/ cab, AC, 6S Dozer w/ tilt, drawbar, Almost new tracks w/ 50% 36" flat pads. Fully serviced and work ready ....................$79,000

1997 CAT D6R LGP, CAB, AC, 6S Dozer, 2003 CAT 330C, Work ready 40T HEX with DRAWBAR, 1200 hr on new UC w/ 36" FLAT reach boom, med stick, QC, GP Bucket, fully PADS, 2700 hr on engine rebuild. Runs great, serviced, Tier 2 engine ......................$69,000 former rental unit ..............................$65,000

2003 CAT 14H, Work ready, larger blade, fully equipped with cab, AC, pushblock, ripper, engine doors, 20.5-25 tires in good condition. 1 of 2 available ................................$149,000

1980 CAT 631D, 2000 hrs on CAT dealer re2012 TEREX TA300, Excellent, low hours, power 3408TA, T-2 engine, cab, AC, retarder, 30T 6x6 Artic with retarder, tailgate, backup 37.25x35 tires at 90%F, good rears. Excellent camera, supplemental steering, good tires. Work ready. One of two available ....$139,500 ..........................................................$99,000

2011 DEERE 544K, LOW Hours, cab, AC, QC with GP Bucket and Forks, in excellent condition, work ready ................................$82,500

(714) 340-1025 • Mike Kustura: sales@EccoEquipment.com

www.eccoheavyequipment.com

Santa Ana, CA – HQ (714) 554-4851

Visalia, CA (559) 651-0116

San Diego, CA (619) 205-2026

Coachella, CA (760) 578-1043

Sacramento, CA (916) 997-7492

Bullhead City, AZ (928) 715-0672

Riverside, CA (951) 276-9025

Stockton, CA (510) 516-5567

Phoenix, AZ (602) 276-2040

Las Vegas, NV (702) 877-4302

Salt Lake City, UT (801) 796-7368

Boise, ID (208) 459-3800

Williston, ND (701) 572-8126

Page 24 • December 19, 2021 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

//DUJH ,QYHQWRU\ RI 3RSXODU DQG DUJH ,QYHQWRU\ RI 3RSXODU DQG 1RW 6R 3RSXODU &RROLQJ 3URGXFWV 1RW 6R 3RSXODU &RROLQJ 3URGXFWV /& t KEΖd , s /d͕ t t/>> D < /d͊ & t KEΖd , s /d͕ t t/>> D < /d͊

x Z / dKZ^ x K/> KK> Z^ $WODQWD &LQFLQQDWL 'DOODV %DOWLPRUH '& +RXVWRQ &KDUORWWH /RV $QJHOHV &KLFDJR

3KLODGHOSKLD 3KRHQL[ 7DPSD 7ROHGR

x , Z' /Z KK> Z^

www.Act tiveRadiator.com

heavy equipment

Armor PROTECTION YOU CAN COUNT ON!

Heavy Equipment Armor is the FIRST and ONLY company dedicated to building ballistic window/ door, top guard, and cab guard products for heavy equipment. Whether your machine is moving dirt with a bucket, lifting materials on the job site, masticating, demolition, or doing a specialized job with an attachment; You can count on HEA ballistic window and cab guards protecting your assets! Our enhanced guarding will be there to help protect the operator and the heavy equipment. Ƥ ǡ ǡ ǡ Ǥ

Our enhanced products like our cab guards for excavators and skid steer armor add another safety protection level for the operator and the machine. A company’s most valuable asset is protected – It’s PEOPLE. This, in turn, reduces injuries which reduce business costs and disruption. Our heavy equipment protection also improves work quality. Insurance claims decrease in safe work environments with Heavy Equipment Armor’s enhanced cab guards and ballistic windows.

TOP PRODUCTS Ballistic Defender Door or Window for Excavators or Skid Steers Bolt on Window Screen for Excavators

Soil Connect Now Includes Time Tracking to E-Ticketing

Bolt on Skeleton Front Door for Skid Steers Enhanced Guarding for both Excavator and Skid Steer

Soil Connect — a digital marketplace connecting those who have soil, aggregates and other building materials with those who need it — has added time tracking to its growing e-ticketing platform, eTickets. The new time tracking feature has been seamlessly integrated into the Soil Connect eTickets platform and allows users to easily reduce timesheet errors and make accurate and timely payments to haulers. An automatically geo-tagged punch-in and punch-out function enables users to analyze route efficiencies and provides a clear picture of the route, along with the complete data set provided by the platform. “We are always looking for ways to solve the many age-old day-to-day problems encountered by contractors in the material hauling and dirt moving world,” said Cliff Fetner, founder and CEO of Soil Connect. “eTickets was designed with the small- to

mid-size contractor in mind, and this new feature provides business owners a time tracking solution that can improve driver and subhauler accountability, without being constantly mired in additional administrative duties, invoice disputes, etc. This can make a real impact on a company’s bottom line.” eTickets is a contactless, easy-to-use e-ticketing platform designed to eliminate the use of paper tickets and allow users to easily capture customer information, type of truck, destination, pictures, eSignatures, type of material, load count and more. eTickets provides a better ticket management solution for any industry that hauls and manages loads, eliminating the human error associated with traditional paper tickets and ultimately helping contractors get paid faster. For more information, visit www.soilconnect.com. 

Paving

SECTION

Pages 25-37

For more information on paving, compaction and milling equipment, as well as comparison charts, visit CEG's Web site at www.constructionequipmentguide.com.

LHC Reaches Compaction in Fewer Passes, Lower Cost For more than 50 years, LHC Inc. has provided construction services to Montana’s Flathead Valley. It has completed and is currently working on some of the Treasure State’s largest, most complex and high-profile projects, including the construction of a nearly $34 million bypass around its home city of Kalispell. LHC’s services include design, engineering and construction of all types of infrastructure undertakings, as well as site work for commercial and other properties. It selfperforms nearly every aspect of a project, including mass earthwork, utility installation, subgrade prep and asphalt paving. LHC supplies the materials for the latter from three strategically located gravel pits around the Flathead Valley. LHC recently added its first two Dynapac CC6200 VI rollers to its asphalt paving operations. With an operating mass of 27,340 lbs. and 84-in. drum width, the CC6200 VI is the largest in Dynapac’s tandem rollers lineup. Operators Dustin Yeadon and Stanley Appelt said the machines have increased productivity and efficiency. “We call them the Swiss Army knives of compaction because they actually work great in all three paving stages: breakdown, intermediate and finish,” said Appelt. “Typically, we just use them for the latter two because you can do both virtually simultaneously with a CC6200 VI. You can do more in one pass than with competitive machines.” Yeadon added, “The ability to get the job done with fewer passes gives us time, labor and fuel savings. We basically can run all day on less than half a tank. And, if we can handle two stages with one machine, that eliminates the need for additional rollers, which increases the savings.” Adjustable Vibration Frequency, User-Friendly Operation Dynapac designed its CC asphalt tandem rollers for high vibration frequency with low amplitude in order to maintain high efficiency on modern, thin asphalt layers. This allows them to compact quickly without crushing the aggregate material. They also can be used for thick layers with high ampli-

lead roller behind the paver, it takes a good, long time for the water to run out. We typically put down 400 to 500 tons between fill ups.”

LHC recently added its first two Dynapac CC6200 VI rollers to its asphalt paving operations. With an operating mass of 27,340 lbs. and 84-in. drum width, the CC6200 VI is the largest in Dynapac’s tandem rollers lineup.

tude and a “normal” vibration frequency. A wide frequency and amplitude range provides optimization in any application. “Being able to adjust the vibration frequency increases versatility,” said Appelt. “We used the CC6200s on everything from smaller parking lots to large-scale highway projects. You can set your numbers to what you need, and it will tell you the range of where you need to be speed-wise for optimized production. That helps with efficiency.” Vibration frequency is set through the new instrument panel and controls that were designed with simplicity in mind. A bigger touch screen ensures maximum visibility. The latest technology simplifies roller operation and ensures optimized handling, thus increasing the quality of the compaction job. “It’s very user-friendly with a dynamic screen that gives you instant feedback with information such as where you’re at in terms of impacts per foot,” said Appelt. “You can input your numbers pre-workday, so you can get right to work when it’s time. If you do need to make a quick adjustment, it’s two or three buttons and you’re back to rolling.”

The swiveling operator’s module in the CC6200 VI allows a 180-degree turn of the seat, instruments and levers. It also can slide from side to side, making it possible for the operator to see drum surfaces, sprinkler nozzles and drum edges. “Sliding and turning is all done with one handle, as opposed to numerous ones like other rollers I have run,” said Yeadon. “You can instantly slide over and get on point. It’s effortless and speeds up operation.” Appelt added, “The visibility is outstanding with the open-cab design. There are no bars in the middle of the cab that you have to look or lean around to see as you go forward. The seat sits up higher than others, so you can see right down in front of you.” Yeadon and Appelt can set how often water from the high-capacity water tank is sprayed on the drums with the control panel and a joystick button. The tank can be filled from both sides of the roller, and there is a two-bar setup on both drums. “If you want water on demand, just push the button; otherwise, you can adjust how often it sprays to match the job,” Yeadon pointed out. “In most cases, even if it’s the

Expanded Partnership That Helps More Contractors LHC Inc. purchased the Dynapac CC6200 VI rollers from Modern Machinery with the assistance of Territory Manager Ben Ralls. Modern has a long history with Dynapac in Montana and Idaho, and earlier this year, it added Wyoming, Washington and Oregon to its territory — making it one of North America’s largest Dynapac dealers. “Modern is well-respected in the market and a perfect fit for Dynapac,” said Dynapac North America Vice President of Sales Jamie Roush when the expansion was announced. “This partnership will enable us to strengthen our brand presence and customer support even further in this region.” Ralls and Modern set up a demo with one CC6200 VI so LHC could put it to the test on a highway paving project. Dynapac representatives, including Western Region Manager Steve Cole, were on hand to answer questions and provide training and support. “They gave us a walk-around and showed us every aspect, which gave us a leg up before we started,” said LHC Inc. Superintendent Cruz Smith. “That was a huge help, and they have followed up since we purchased the machines to make sure everything continues to run smoothly. We are looking forward to doing more business with them after purchasing these rollers and seeing how they increase our productivity.” Ralls emphasized that others could see similar results. “I have seen these and other Dynapac rollers get compaction where other brands would struggle. Having equipment like Dynapac, that’s backed by great manufacturer service and support, plays a strategic role in Modern Machinery’s ability to build trust with customers. Both companies are excited about the partnership expansion, as it gives us the ability to help other customers like LHC be more productive, efficient and profitable.” For more information, visit www.dynapac.us. 

Page 26 • December 19, 2021 • www.constructionequipmentguide.com • Paving Section • Construction Equipment Guide

NAPA ‘Pave It Black’ Podcast Highlights Tech Innovations By Tom Gresham NAPA

New technologies are reshaping the asphalt pavement industry, and the pace of change is accelerating as high-tech tools grow both more sophisticated and accessible. During Season 3 of “Pave It Black,” NAPA’s podcast covering the people and issues affecting the industry, hosts Richard Willis and Brett Williams interviewed industry experts to dig deeper into the innovations that are most affecting the realm of asphalt pavement — and that promise to change the way the industry operates long into the future. Episode 1: “What Is Innovation?” In Episode 1, Nicholas Webb, founder and CEO of LeaderLogic and the keynote speaker at the 2020 NAPA Annual Meeting, detailed his thoughts on the concept of innovation and how it promises to impact the asphalt pavement industry. Episode 2: “It’s Electric” Dan Gallagher, president of Gallagher Asphalt, discussed the growing electrification of vehicles and how that affects the asphalt industry — an industry funded in part by gas taxes through the Highway Trust Fund. Episode 3: “Innovation = Business Opportunities” Katie Peabody, senior business analyst with Lakeside Industries, joined “Pave It Black” to discuss the far-reaching impact of new developments in computing technology. “Everything is definitely evolving,” she said. “As an organization, we realize the importance of these technologies in order to continue to thrive in the industry, even though it isn’t always easy to adopt and utilize technology.” Episode 4: “Big Data in the Asphalt Industry” Dan Ridolfi, president of California-based LASTRADA Partners, dove into how data analytics and artificial intelligence can help operators “focus on what matters.” Ridolfi explained, “What we have the ability to do today is expand the databases, and that’s kind of what’s exciting about our world.” Episode 5: “Temperature, Temperature, Temperature” Brent Carron, president of Valley Paving in Minnesota, explained the benefits of thermal profiling, a tool not widely used in the industry, but one that offers an opportunity for contractors to ensure high-quality asphalt pavements. Episode 6: “Going Paperless”

Hosts Brett Williams (in foreground) and Richard Willis discuss technology issues on NAPA’s “Pave It Black” podcast.

Dan Ganoe, vice president of operations for Lindy Paving in Pennsylvania, discussed the implementation of e-ticketing and how to move to a paperless world. Episode 7: “Robots Help in the Work Zone” During National Work Zone Awareness Week, Todd Hendricks, Jr., president of Ohio-based Pioneer Industrial Systems, shared that his company is pursuing two robotics solutions for road maintenance projects: sealing cracks on roads and setting and picking up cones in work zones. Episode 8: “Efficient Fleet Management” Mike Wills, area manager for Californiabased Granite Construction, said technology is allowing for much more efficient deployment of trucks to sites, such as through an app that Granite uses with drivers. Episode 9: “The Dynamics of Asphalt Plant Management” Ben Adomyetz, sales representative and estimator for the Rogers Group in Alabama, described how software can help asphalt operators plan, track, and communicate, such as during the transition from the bidding process for a project to the project itself. Episode 10: “Doing More with Drones” Carl Pittman, a civil engineer with Apac Mississippi, and Jessica Lewis, a graduate student at Mississippi State, provided their insight into the ways that drones have increased safety and efficiency at project and plant sites. “The real success in a drone program is going to come down to how you use that data,” Pittman said. “You can go collect all the data you want. If it sits in an Excel spreadsheet, and never goes anywhere, you’re not really doing much with it.” (Reprinted with permission from the National Asphalt Pavement Association) 

Construction Equipment Guide • Paving Section • www.constructionequipmentguide.com • December 19, 2021 • Page 27

BUILT TO CONNECT

Efficiency and Productivity Designed with safety and operator comfort in mind, the Shuttle Buggy® 3000 material transfer vehicle features adaptive cruise control, bright LED lighting, four-wheel steering for easy transport and ground-level maintenance access for added convenience. Operators can rely on clear sightlines and the ground operator is safely protected inside the structure of the machine. The Roadtec SB-3000 is the perfect blend of traditional craftsmanship and modern technology.

astecindustries.com ARIZONA/NEVADA/UTAH

CALIFORNIA

OKLAHOMA

OREGON/WASHINGTON/ MONTANA/IDAHO

TEXAS

Goodfellow Corporation www.goodfellowcorp.com (801) 796-6126

Herrmann Equipment www.herrmannequipment.com N CA (916) 783-9333 S CA (909) 877-5597

Van Keppel www.vankeppel.com (844) 499-6363

Modern Machinery www.modernmachinery.com (800) 332-1617

Closner Equipment www.closner.com (210) 732-2131

WYOMING/COLORADO

Power Motive Corporation www.powermotivecorp.com (303) 355-5900

Page 28 • December 19, 2021 • www.constructionequipmentguide.com • Paving Section • Construction Equipment Guide

Products shown with optional equipment.

MAULDIN Paving g Products... MASTERS S OF THE MA AT! T! Contact your MAULDIN N dealership today to see the newly redesigned M415XT! For more information visit us at www.4aMauldin.com.

Golden Equipment Company www.goldenequipment.com 721 Candelaria Rd NE 29268 Hwy 160 Albuquerque, NM 87107 Durango, CO 81303 (505) 345-7811 (970) 247-8830

1150 Madison Lane Farmington, NM 87401 (505) 326-1413

Closner Equipment www.closner.com 6532 East Highway 114 13800 FM 973 N Rhome, TX 76078 Manor, TX 78653 (817) 708-9108 (512) 272-8200

21910 FM 2252 Schertz, TX 78154 (210) 732-2131

Tri-State Truck & Equipment, Inc. 5250 Midland Rd. Billings, MT 59101 (406) 245-3188

www.tste.com 1271 N. Derrick Dr. Casper, WY 82604 (307) 472-1818

5024 Tri Hill Frontage Rd. Great Falls, MT 59404 (406) 452-9551 200 Floss Flats Rd. #1 Belgrade, MT 59714 (406) 388-5815

1319 Elk St. Rock Springs, WY 82901 (307) 362-4000

Construction Equipment Guide • Paving Section • www.constructionequipmentguide.com • December 19, 2021 • Page 29

KIRBY-SMITH MACHINERY INC.

NUECES POWER EQUIPMENT

www.kirby-smith.com

www.nuecespower.com

6715 W. Reno Oklahoma City, OK 800-375-3339 McAlester, OK 918-310-1550 Tulsa, OK 918-438-1700

Dallas, TX 214-371-7777 Fort Worth, TX 817-378-0600 Abilene, TX 325-692-6334 Amarillo, TX 806-373-2826

Lubbock, TX 806-745-2112 Odessa, TX 432-333-7000 Waco, TX 254-261-1370

Corpus Christi, TX 361-289-0066 Laredo, TX 956-725-0066 San Benito, TX 956-361-0066 Victoria, TX 361-576-0066

Vinton, TX 915-541-0066 Houston, TX 713-247-0066 San Antonio, TX 210-310-0066

HONNEN EQUIPMENT CO. www.honnen.com Denver, CO 303-287-7506 800-646-6636 Durango, CO 970-247-4460 Grand Junction, CO 970-243-7090

Idaho Falls, ID 208-523-9915 Salt Lake City, UT 801-262-7441 Ogden, UT 801-627-0049 St. George, UT 435-652-8003

Casper, WY 307-266-4474 Cheyenne, WY 307-316-9800 Gillette, WY 307-685-4288 Rock Springs, WY 307-382-5284

Page 30 • December 19, 2021 • www.constructionequipmentguide.com • Paving Section • Construction Equipment Guide

The work may be under your feet, but you’re looking ahead - to the next challenge and the next deadline. Your local Cat Dealer RœHUV VDOHV VHUYLFH DQG VXSSRUW IRU WKH IXOO :HLOHU FRPPHUFLDO SDYLQJ OLQH LQFOXGLQJ SDYHUV WDFN GLVWULEXWRUV DQG FRPSDFWRUV

Built to Exceed the Demands of the Commercial Paving Contractor

WE’RE RIGHT THERE WITH YOU Cashman Equipment

Holt of California

Quinn CAT

N C Machinery

Tractor & Equipment

cashmanequipment.com

holtca.com

quinncompany.com

ncmachinery.com

tractorandequipment.com

Serving Nevada & the Eastern Sierras 888-CASHMAN (888-227-4626) Henderson/Las Vegas, NV Elko, NV Reno/Sparks, NV Round Mountain, NV Winnemucca, NV

7310 Pacific Avenue Pleasant Grove, CA 95668 916-921-8800 1521 West Charter Way Stockton, CA 95206 209-466-6000 3440 East Pacheco Blvd. Los Banos, CA 93635 209-826-4919

Bakersfield, CA 661-393-5800 Foothill Ranch, CA 949-768-1777 Fresno, CA 559-896-4040 Los Angeles, CA 562-463-4000 Riverside, CA 951-686-4560

Tukwila, WA 425-251-5800 Chehalis, WA 360-748-8845 Fife, WA 253-896-0878 Monroe, WA 360-805-6000 Mount Vernon, WA 360-424-4292 Port Angeles, WA 360-452-9222

East Wenatchee, WA 509-886-5561 Yakima, WA 509-248-2371 Anchorage, AK 907-786-7500 Fairbanks, AK 907-452-7251 Juneau, AK 907-789-0181 Wasilla, AK 907-352-3400

Billings, MT 406-656-0202 Bozeman, MT 406-585-5800 Great Falls, MT 406-761-7900 Helena, MT 406-442-2990 Williston, ND 701-713-2100 Worland, WY 307-347-4747

Roads must be built. Worlds must be connected.

Construction Equipment Guide • Paving Section • www.constructionequipmentguide.com • December 19, 2021 • Page 31

DOUBLE DRUM OSCILLATION & HIGH FREQUENCY

DURABLE EASY TO USE

POWER MOTIVE CORP. www.powermotivecorp.com

5000 Vasquez Blvd. Denver, CO 80216 303/355-5900

Grand Junction, CO 970/241-1550

Colorado Springs, CO 719-576-5541

Milliken, CO 970/587-1188

Durango, CO 970/259-0455

Cheyenne, WY 307/634-5149

NED - Texas www.nedealers.com

Formerly Four Seasons Equipment Houston, TX 800-234-5007 281-807-9777 Dallas, TX 866-270-1700 214-388-1700

CISCO EQUIPMENT www.cisco-equipment.com

1706 S. 1st Street Artesia, NM 88210 800-748-1846

2707 Slaton Hwy Lubbock, TX 79404 877-745-9595

520 SE Loop 338 Odessa, TX 800-657-3673

620 N. Bell St. San Angelo, TX 76903 800-496-0271

WESTRAX MACHINERY www.westraxmachinery.net

19618 S. Susana Road Rancho Dominguez, CA 90221 800-411-4717 19885 Temescal Canyon Road Corona, CA 92881 800-411-4717 611 N. Golden Key Street Gilbert, AZ 85233 602-397-8173

www.sakaiamerica.com (800) 323-0535

Page 32 • December 19, 2021 • www.constructionequipmentguide.com • Paving Section • Construction Equipment Guide

New Addition...

866-430-7539

www.jfwequipment.com sales@jfwequipment.com

Serving the Asphalt Industry for 30 Years

Bomag Names Newest Vice President of Milling, Paving

2009 Etnyre Centennial II distributor, 2000 gallons, BT-1 computer, propane burners, 14 ft spray bar, 2009 Sterling L7500 w/Mercedes dsl eng, 6 spd trans, 2 spd axle $87,000

2012 Broce RJT350 broom, heat & a/c, John Deere 4.5L turbo diesel engine, 8 ft broom, hyd. drive, water system, broom core 80%, all new tires - $31,000

2015 Laymor Sweepmaster SM400 broom, Kubota diesel engine, water system, 8 ft broom, cab w/heat & a/c, all new tires - $36,000

2011 Laymor 8HC broom, tow hitch, Kubota diesel engine, 8 ft broom - $16,500

1989 Etnyre chip spreader, 12 ft spread hopper, Cummins 5.9L diesel engine, hydrostatic drive, 2WD $18,000

Chris Colwell joined Bomag as vice president of milling and paving.

New Marathon TPS115S tack distributor, Honda gas eng, 10GPM pump, 115 gallons, 5 ft spray wand w/50ft hose, hose reel, 80,000 BTU propane burner, flushing system - $8795

New Marathon TPS250T tack distributor, Honda gas eng, 10GPM pump, 250 gal, 5 ft spray wand w/50 ft hose, propane heat, flushing system, electric brakes $12,200 (also avail w/spray bar)

1998 Cat PS150B pneumatic 9 wheel roller, Caterpillar diesel engine, hydrostatic drive, water system - $31,000

New Marathon TPS500PT tack distributor, Honda gas eng, 18GPM pump, 500 gal, 5’ spray wand w/50’ hose, hose reel, 6 ft spray bar, operator’s platform, propane burners, flushing system, electric brakes - $23,800

3517 Wayne White Rd., Climax, NC 27233

Bomag Americas Inc. has welcomed Chris Colwell as vice president of milling and paving. Colwell will be responsible for developing and leading a new business unit segment focused on optimizing the sales and product support for milling, paving and reclaiming customers. Colwell brings 35 plus years of road construction equipment experience, having worked for both manufacturers and dealers, so he has a keen understanding of what is required to support end users. Prior to joining Bomag, he spent 10 years with Astec Industries, with his most recent positions as vice president channel management and president of Carlson Paving Products. Prior to joining Astec, Colwell spent several years managing a road construction equipment dealership based in Michigan.

“Colwell’s extensive background in roadbuilding products, change leadership and understanding the high sense of urgency to provide immediate solutions for customers is exactly what Bomag requires to help customers expand their business with us,” said Rob Mueckler, president of Bomag. “I strongly believe in Bomag’s products, its vision to strengthen its presence in the roadbuilding sector and, most importantly, the commitment Bomag has to additional investments to improve support for milling, paving, and reclaiming customers,” Colwell said. “I look forward to leading a dedicated team of sales, product and service personnel to support our customers and mutually capitalize on our growth opportunities in paving, milling and reclaiming.” For more information, visit www.bomag.com/us. 

Construction Equipment Guide • Paving Section • www.constructionequipmentguide.com • December 19, 2021 • Page 33

BUILT TO CONNECT

A Workhorse To Depend On The Carlson CP100 II sets the standard for versatility, component lifecycle and mat quality. With a powerful 100hp engine, an array of configurations and the class-leading EZCSS single slide screed, it’s time to see why the CP100 II has fast become the contractor’s choice for heavy-duty commercial paver platforms.

astecindustries.com

www.goodfellowcorp.com www.cooperequip.com 5210 N Loop 1604 E San Antonio, TX 78247 (210) 657-5151 201 Commerce City Blvd. Georgetown, TX 78626 (512) 930-5151

390 North 200 West Lindon, UT 84042 (801) 796-6126 12451 Old U.S. 95 Boulder City, NV 89005 (702) 293-7504

www.modernmachinery.com Kent, WA (800) 669-2425

Billings, MT (800) 735-2589

Rochester, WA (800) 304-4421

Kalispell, MT (800) 434-4190

Spokane, WA (800) 541-0754 Boise, ID (800) 221-5211 Pocatello, ID (800) 829-4450

Missoula, MT (800) 332-1617 Eugene, OR (800) 826-9811 Portland, OR (800) 950-7779

www.herrmannequipment.com

www.closner.com

Northern California 9220 Viking Place Roseville, CA 95747 (916) 783-9333

6532 East Highway 114 Rhome, TX 76078 (817) 708-9108

Southern California 2711 Lilac Ave. Bloomington, CA 92316 (909) 877-5597

21910 FM 2252 Schertz, TX 78154 (210) 732-2131 13800 FM 973 N Manor, TX 78653 (512) 272-8200

Page 34 • December 19, 2021 • www.constructionequipmentguide.com • Paving Section • Construction Equipment Guide

Construction Equipment Guide • Paving Section • www.constructionequipmentguide.com • December 19, 2021 • Page 35

s®Ý®ã ÊÄ Ê¥ ÊçÙ s® ½ ÙÝ ããÊ Ê ù͊

MF25 500CS Feed der APCO EQUIPMENT ENT www.apcoequipment.com nt.com 3432 N 5th Street eet N. Las Vegas, NV 89032 (800) 574-40899

5HGHÀQLQJ WKH WRWDO FRVW RI RZQHUVKLS Challenging the Status Quo — NOW with IMIX two stage mixi

BANE MACHINER RY Y, INC. Y, ZZZ EDQHPDFKLQHU\ U\ FRP 2449 Manana Rd. 'DOODV 7; (214) 352-24688 )W :RUW UWK 7; ; (817) 847-58944 7\OHU 7; 7\ (903) 597-66411

CLAIREMONT EQUIPMENT PMENT ZZZ FODLUHPRQWHTXLSP PHQW FRP 7651 Ronson Road ad San Diego, CA 921111 (858) 278-8351 1330 W Mission Road oad Escondido, CA 92029 029 (760) 739-9100 440 West Aten Road oad ,PSHULDO &$ (760) 355-7700 4726 Convoy Street eet San Diego, CA 921111 (858) 278-8338

&ORVQHU (TXLSPHHQW ZZZ FORVQHU FRP BEE EQUIPMENT SALES ALES LTD. L ZZZ EHHHTXLSPHQWVVDOHV FRP 2506 Slaton Highway way /XEERFN 7; (806) 745-1511

6532 East Highway 114 1 Rhome, TX 76078 78 (817) 708-9108 21910 FM 2252 Schertz, TX 78154 54 (210) 732-2131 13800 FM 973 N Manor, TX 786533 (512) 272-8200

C. L. BOYD CO., INC. ZZZ FOER\G FR RP 4220 West Reno Ave. A 2NODKRPD &LW\ 2. (800) OKC-BOYD • (405)) 942-8000 Ardmore, OK K (866) 720-2693 • (580) 224-2693 Lawton, OK (800) 633-2693 • (580) /355-6667

/ŶƋƵŝƌĞ ĂďŽƵƚ ǇŶĂƉĂĐ͛Ɛ ^ƉĞĐŝĂů &&ŝŝŶĂŶĐŝŶŐ KīĞƌƐ͘

DOGGETT HEA AVY VY Y MACHINER RY Y SERVICES CES www.doggett.com m $OH[DQGULD /$ (318) 442-0455 Baton Rouge, LA (225) 291-3750 Broussard, LA (337) 837-9481 Covington, LA (985) 893-3005 /DNH &KDUOHV /$ (337) 430-3045 Monroe, LA (318) 343-8787 Shreveport, LA (318) 631-3090 St. Rose, LA (504) 466-5577 Beaumont, TX (409) 842-1754 Bryan, TX (979) 823-1905 Corpus Christi, TX X (361) 289-0727 Houston, TX (713) 679-6700 Longview, TX (903) 758-3326 Lufkin, TX (936) 634-8801 San Juan, TX (956) 787-0001 7\OHU 7; 7\ (903) 592-8900 Victoria, TX (361) 570-6666

MODERN MACHINER RY R Y www.modernmachinery..com &RUSRUDWH 2IÀ IÀFH 0LVVRXOD 0RQWDQD (409) 842-1754 Boise, Idaho (208) 336-8670 Jerome, Idaho (208) 324-4522 3RFDWHOOR ,GDKR (800) 829-4450 %LOOLQJV 0RQWDQD (800) 735-2589 &ROXPELD )DOOV 0RQWDQ QD (800) 434-4190 Eugene, Oregon (800) 826-9811 3RUW UWODQG 2UHJRQ (800) 950-7779 Kent, Washington (800) 669-2425 Rochester, Washington g n (800) 304-4421 Spokane, Washington n (800) 541-0754

ROAD MACHINER RY Y www.roadmachinery.com om

COOPER EQUIPMENT NT CO. www.cooperequip.com .com 5210 N Loop 16044 E San Antonio, TX 78247 8247 (210) 657-5151 201 Commerce Blvd. vd. Georgetown, TX 78626 8626 (512) 930-5151

Follow Dyynapac North America

ĞƐŝŐŶ ŶĞĚ ƚŽ ƉĞƌĨ ƌĨŽƌŵ ƌŵ͕ Ƶŝůƚ ƚŽ ůĂƐƚ

dyn napac.us | 800-65 51-0033

902 S. 7th Street Phoenix, AZ 85034 (480) 545-2400 Prescott, AZ (928) 778-5621 Tuscon, AZ (520) 623-8681 %DNHUVÀHOG &$ (661) 695-4830 Perris, CA (909) 355-3600 Pico Riviera, CA (562) 699-6767

Page 36 • December 19, 2021 • www.constructionequipmentguide.com • Paving Section • Construction Equipment Guide

Contact your local dealer:

Arnold Machinery Company www.arnoldmachinery.com 2975 West 2100 South Salt Lake City, UT 801-972-4000 Idaho Falls, ID 208-523-0822 Meridian, ID 208-887-6000 Twin Falls, ID 208-733-1715 Elko, NV 801-972-4000 Sparks, NV 775-356-1511 Las Vegas, NV 702-642-9000 Phoenix, AZ 602-414-1900

Peerformmancee you o cann count on. oon

Tucson, AZ 520-294-7677

Local Dealer Local dealer address Pacwest Machinery 000.000.0000 www.pacwestmachinery.com www.localdealerweb.xx 8207 South 216th Street Kent, WA 98032 Local Dealer 800-935-5933

Local dealer address

4030 East Trent Avenue Spokane, 000.000.0000 WA 99202 800-938-5933 www.localdealerweb.xx 19255 NE Sandy Blvd Portland, OR 97230 Local Dealer 800-929-5933

Local 1550 Irving Roaddealer address Eugene, OR 97402 000.000.0000 866-920-5933

www.localdealerweb.xx

Local Dealer Local dealer address Sierra Machinery 000.000.0000 www.sierraelpaso.com www.localdealerweb.xx 939 Hawkins Blvd. El Paso, TX 79915 Local Dealer 915-772-0613

Local dealer address

7179 Roswell Hwy. 000.000.0000 Artesia, NM 88210 575-746-6592 www.localdealerweb.xx

Local Dealer Local dealer address 000.000.0000 Volvo Construction Equipment & Services www.localdealerweb.xx www.vcesvolvo.com Bakersfield, CA 661-387-6090 Corona, CA 951-277-7620 Fresno, CA 559-834-4420 Sacramento, CA 916-504-2300

DEALER LOGO

Lakeside, CA 619-441-3690 San Leandro, CA www.localdealerweb.xx 510-357-9131 Turlock, CA 209-410-6710

At Volvo, we e know that you need reliable, iable, durable dur and capablle paving equipment. pment. That’s why we wo ork to build sustainable, productive a and innovative machines that hat help you y get more done faster. The future is waiting – turrn to your nearest Volvo dealer to lea arn more.

Construction Equipment Guide • Paving Section • www.constructionequipmentguide.com • December 19, 2021 • Page 37

ARNOLD MACHINERY COMPANY www.arnoldmachinery.com Las Vegas, NV 702/642-9000 Phoenix, AZ 602/414-1900 Tucson, AZ 520/294-7677

ASCO EQUIPMENT www.ascoeq.com Beaumont, TX 409/212-8100 Brenham, TX 979/836.6641 (North) Houston, TX 281/987.1990 (South) Houston, TX 713/649.0940

BEE EQUIPMENT SALES, LTD www.beeequipmentsales.com Lubbock TX 806/745-1511 866/796-3211

KIRBY-SMITH MACHINERY, INC. www.kirby-smith.com Oklahoma City, OK 800/375-3339 McAlester, OK 918/310-1550 Tulsa, OK 800/375-3733 Kansas City, KS 877/851-5729

ROMCO EQUIPMENT CO. www.romco.com Austin, TX 512/388-2529 877/851-1026 Buffalo, TX 903/322-5602 Dallas (Carrollton), TX 214/819-4100 800/227-6626 Ft. Worth, TX 817/626-2288 866/966-4602

Longview, TX 903/758-5576 Midland, TX 432/234-9409 San Antonio, TX 210/648-4600 800/966-4601

Page 38 • December 19, 2021 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

Growing Demand...

Soosan America’s Rock Commander Infrastructure Bill Gives Flynn Brothers Inc. Confidence Calls On Industry to

To supplement their teacher incomes, brothers John and on employees equipped with reliable and highly productive Jesse Flynn started an asphalt patching and driveway paving equipment to accomplish the task on time. For drilling rock, business in the Louisville, Ky., area in 1973, working from the company turns toRock Commander rock drills. the back of their pickup truck. Flynn Brothers Inc. took off Flynn Brothers has used Soosan America’s Rock and younger brother, Ed, joined the company in 1980. In Commander rock drills for the majority of its drilling needs 1982, Jim Rice came on board to serve as a partner in the since 2018. The company currently has three Rock business. Under this management team, the company grew, Commander drills in its fleet: a JD1400E-II and two with operations expanding to take on paving, sitework and utility projects. Flynn Brothers Inc. became an employee-owned company in 2004 and its operations have continued to grow. Major projects include a total pavement replacement on a heavily trafficked stretch of Interstate 65 in Louisville; excavation, clearing and sanitary line installation for the 40-acre Buechel Basin Wastewater Storage Facility; and site work, underground utilities and asphalt paving for the Paddock Shops, one of Louisville’s largest shopping centers. Noted for its experience and expertise with projects involving the area’s uniquely hard limestone, Flynn Brothers was awarded the contract to conduct site work and Flynn Brothers was awarded the contract to conduct site work and excavation for Republic National excavation for Republic National Distributing Company’s new faciliDistributing Company’s new facility. ty. Republic markets and distributes wine and spirit products to bars, restaurants, hotels and liquor stores JD800E-II drills. throughout Kentucky. The company has more than 300 employees and handles more than 50 percent of wine and Rock Commander JD1400E-II almost half of the bourbon sold in Kentucky. The new comDesigned to be economical yet dependable, the JD1400Eplex, located on Blankenbaker Parkway in Louisville, will II is powered by the Cummins QSL9 engine, with a GHH include a 326,000-ft. warehouse and office complex. Rand compressor and the YH135 drifter. The JD1400E-II can drill deep holes from 3.5 to 5 in. in diameter, with fast drilling rates and low maintenance cost, according to the company. To improve overall productivity and reduce operator fatigue, the unit features a large cab design and tilt console for greater comfort. Available options include an extendable boom, water suppression, angle system and longer mast.

Flynn Brothers currently has three Rock Commander drills in its fleet: a JD1400E-II and two JD800E-II drills.

Jim Slinker, head of Flynn Brothers’ drilling and blasting division, was on site in October to begin the project. Slinker estimates that there are 80,000 yds. of mass rock along with storm sewer, sanitary sewers and water supply line access that requires drilling and blasting. Drilling depths for the project will range from 10 to 21 ft., based on the current plans. While Republic National Distributing Company relies on Flynn Brothers to get the work done, Flynn Brothers relies

Rock Commander JD800E-II The newest addition to the Rock Commander lineup — the JD800-II — is smaller than the JD-1400E-II but shares a majority of the large machine’s components. The JD-800EII features a large cab design and tilt console and can operate with T45 or T51 drill steel and can handle hole diameters ranging from 2.75 to 4 in. The JD800-II is powered by a Cummins QSB6.7, providing power for operating the hydraulics, compressor and the YH80A drifter. The JD-800E-II is used by construction and development contractors that need to drill a mid-size hole without breaking the bank. With more than a year’s worth of work complete on this project, downtime has been kept to a minimum due to Soosan’s simple to maintain systems. Rock Commander drills are front and center on Flynn Brothers’ latest project, as well as hundreds of other projects currently under way throughout the United States and Canada. For more information, visit rockdrills.net.  CEG

Require Innovation The construction industry has burst into a flurry of activity as the most aggressive infrastructure spending initiative since the 1950s was signed into law on Nov. 15. Combined with a skilled labor shortage, the $550 billion bill calls into question whether contractors have the capacity to meet rapidly growing demand. Innovative contractors across the nation are turning to new technology for help. Robots as a new class of equipment are showing to be an effective complement to human crews and may prove essential to completing the projects laid out within the infrastructure bill. Woman owned Disadvantaged Business Enterprise, Shelby Erectors, is an example to contractors across the country on the effective usage of robotics on the job site. Contracted for rebar installation on the 512,427 sq. ft. I-95 Express Phase 3C project in Ft. Lauderdale, Fla., Shelby elected to utilize TyBot by Advanced Construction Robotics to boost crew productivity. TyBot, a rebar tying robot, leverages cutting edge artificial intelligence to tie together the rebar grid that commonly reinforces concrete surfaces. While TyBot is actively tying rebar, Shelby’s laborers are free to handle more skilled tasks better suited for human hands. Shelby stands tall in the industry as an example of how to adapt to modern challenges, and its president, Jennifer Nix, is positioning her company to meet the labor demands of the new infrastructure bill. “As the labor gap in construction continues to grow with increasing demand, it is crucial to incorporate solutions like TyBot to mitigate the effects. We have found that TyBot saves at least 25 percent on our rebar tying schedule. This provides a crucial edge when bidding projects, and project owners, typically DOT, often like to see innovative tech used,” Nix said. “TyBot is definitely a lifesaver when labor availability is lacking. It provides a level of consistency that’s difficult to match and is why we’re currently using it on three separate concrete bridge construction projects across Florida. “TyBot removes the repetitive, back-breaking work that can cause serious long-term injuries, and anything we can do to improve our crews’ health and safety is a huge priority for us. TyBot allows us to safely stay on schedule while shorthanded and to move our workforce on to higher skilled tasks or to another jobsite where they can be better utilized,” said Nix. “ACR was founded for moments like this. Our robots will continue to solve today’s construction challenges assisting the workforce to meet rapidly growing demand, such as what will generated from the infrastructure bill,” said Searock, cofounder, ACR. For more information, visit www.constructionrobots.com. 

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • December 19, 2021 • Page 39

REDEFINE THE DAILY GRIND.

Looking to maximize your day-to-day operations? Pressure-compensated load-sensing (PCLS) hydraulics on the newly redesigned John Deere 310SL Backhoe Loader smoothly increase your cycle times with 16% greater rear backhoe trenching productivity* and 15% more craning capacity.** Along with John Deere Connected Support™, you can elevate your underground operation above expectations and plan to do more every day. JohnDeere.com/Backhoes

*Based on rear backhoe trenching productivity study, compared to previous model. / **With Lift Mode enabled, compared to previous model.

4RIVERS EQUIPMENT

YELLOWHOUSE MACHINERY

HONNEN EQUIPMENT CO.

DOGGETT HEAVY MACHINERY SERVICES

www.4riversequipment.com

www.yhmc.com

www.honnen.com

www.doggett.com

Colorado Springs, CO 719.475.1100

Broken Bow, OK 580-584-3222

Amarillo, TX 806-335-1681

Frederick, CO 303.833.5900

Enid, OK 580-233-5000

Dalhart, TX 806-884-4994

Albuquerque, NM 505.884.2900

Tulsa, OK 918-245-5926

Lubbock, TX 806-748-4700

Farmington, NM 505.326.1101

McAlester, OK 918-423-2555

Abilene, TX 325-677-2291

Hobbs, NM 575.392.6923

Midland/Odessa, TX 432-580-3337

El Paso, TX 915.598.1133

San Angelo, TX 325-651-3337

Denver, CO 303-287-7506 800-646-6636 Durango, CO 970-247-4460 Grand Junction, CO 970-243-7090 Ogden, UT 801-627-0049 Salt Lake City, UT 801-262-7441

St. George, UT 435-652-8003 Casper, WY 307-266-4474 Cheyenne, WY 307-316-9800 Gillette, WY 307-685-4288 Rock Springs, WY 307-382-5284 Idaho Falls, ID 208-523-9915

9111 North Freeway Houston, TX 77037 713-679-6700 Beaumont, TX 409-842-1754 Bryan, TX 979-823-1905 Corpus Christi, TX 361-289-0727 San Juan, TX 956-787-0001

Victoria, TX 361-570-6666

Lufkin, TX 936-634-8801

Alexandria, LA 318-442-0455

Monroe, LA 318-343-8787

Baton Rouge, LA 225-291-3750

Shreveport, LA 318-631-3090

Broussard, LA 337-837-9481

St. Rose, LA 504-466-5577

Covington, LA 985-893-3005

Tyler, TX 903-592-8900

Longview, TX 903-758-3326

Page 40 • December 19, 2021 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

-2 2))( 3* 6)40%')1)28 69&&)6 86%'/7#

'%00 97 83(%= 83 +)8 8,) &)78 46-') 32 69&&)6 86%'/7 =%21%6 4%687 %2( 92()6'%66 92()6'%66-%+) 4%687

;IƅVI TVSYH XLEX (SQMRMSR 6YFFIV 8VEGOW EVI XLI

7)00-2+ 69&&)6 86%'/ FVERH MR %QIVMGE %WLPERH :% "" .EGOWSRZMPPI *0 "" 'MRGMRREXM 3, "" 4SVXPERH 36 "" 7GLIRIGXEH] 2= "" (EPPEW 8<

ZZZ GHSSDUWV FRP

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • December 19, 2021 • Page 41

NED - Texas

Porter Group USA

Orion Equipment

Formerly Four Seasons Equipment

13013 Temescal Canyon Rd. Corona, CA 92883 951-674-9999 9879 San Fernando Rd. Pacoima, CA 91331 818-834-0102 www.portergroupusa.com

18060 Des Moines Memorial Drive Seattle, WA 98148 800-280-8124 www.orion-equip.com

Houston, TX 800-234-5007 • 281-807-9777 Dallas, TX 866-270-1700 • 214-388-1700 www.nedealers.com

Page 42 • December 19, 2021 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • December 19, 2021 • Page 43

PERFORMANCE WHERE IT COU C NTS TS

www.andersonmachinerytexas.com

FINANCING

A LOW AS AS

Austin, TX

Odessa, TX

(512) 272-8133

(432) 561-8933

Corpus Christi, TX

San Antonio, TX

(361) 289-6043

(210) 661-2366

Pharr, TX

Victoria, TX

(956) 781-5995

(361) 575-8111

Page 44 • December 19, 2021 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

Contact your local dealer:

ARNOLD MACHINERY CO. www.arnoldmachinery.com

Salt Lake City, UT

Sparks, NV

801-972-4000

775-356-1511

Idaho Falls, ID

Las Vegas, NV

208-523-0822

702-642-9000

Meridian, ID

Phoenix, AZ

208-887-6000

602-414-1900

Twin Falls, ID

Tucson, AZ

208-733-1715

520-294-7677

ROMCO EQUIPMENT CO. www.romco.com

Austin Round Rock, TX

Ft. Worth Ft. Worth, TX

512-388-2529 877-851-1026

817-626-2288 866-966-4602

Buffalo Buffalo, TX

Houston Houston, TX

903-322-5602

713-937-3005 800-865-6998

Carmine Carmine, TX 979-278-3570

Kirby-Smith Hires Joel Cook as Executive Vice President, GM of Construction Group Kirby-Smith Machinery (KSM) continues to build its executive team with the addition of Joel Cook as its new executive vice president and general manager, construction group. Cook will be responsible for strategic direction, operational management and overall leadership of the heavy equipment distributor’s construction group, which includes a current territory with 12 physical locations throughout Oklahoma, Texas, Kansas and Missouri. “Joel is very humble, direct and talented in dealing with customers and team members alike,” said Jeff Weller, chief operating officer. “He is already an outstanding addition to KSM as our new EVP-GM, Construction Group, and we are excited for Joel, his wife Leslie and their family to call Oklahoma City home.” Cook comes to KSM with a diverse background that includes experience both within the heavy equipment industry and the areas surrounding it.

Corpus Christi Corpus Christi, TX 361-881-4891

Dallas Carrollton, TX 214-819-4100 800-227-6626

Longview Longview, TX 903-758-5576

Rio Grande Valley Mercedes, TX 956-565-0100

San Antonio San Antonio, TX 210-648-4600 800-966-4601

SIERRA MACHINERY, INC. www.sierraelpaso.com

El Paso, TX 915-772-0613

Artesia, NM 575-746-6592

Joel Cook

He started his journey with CIT, building a career in customer-facing financing for heavy equipment and management of large dealer portfolios. In 2006, Cook joined Komatsu Equipment Company, a Komatsuowned dealership based in Salt Lake City, where he held several key positions over 14 years, most notably as executive vice president — mining, construction and rental sales. Before joining KSM, Cook most recently

served as president and CEO of Road Machinery, a Komatsu distributor in Phoenix. “I have always admired Mr. Kirby and the great organization he has built. It is an honor to now be part of it, and I look forward to helping in its continued growth and prosperity through customer and company focus,” Cook said. For more information, call 888/8610219 or visit kirby-smith.com. 

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • December 19, 2021 • Page 45

Contact your local dealer:

ASCO EQUIPMENT www.ascoeq.com

Abilene, TX 325-698-2726

Amarillo, TX 806-372-8386

Lubbock, TX 806-745-2000

Perryton, TX 806-435-7773

Clovis, NM 575-742-2726

PACWEST MACHINERY www.PacWestMachinery.com

Spokane Local Valley, DealerWA 509-534-5933

Local dealer address

Portland, OR 000.000.0000 503-252-5933

www.localdealerweb.xx

Eugene, OR 541-302-3762

Local Dealer

Kent, WAdealer address Local 206-762-5933

000.000.0000 www.localdealerweb.xx

Local Dealer Local dealer address 000.000.0000 www.localdealerweb.xx VOLVO CONSTRUCTION EQUIPMENT Local Dealer& SERVICES www.vcesvolvo.com

Local dealer address

Bakersfield, CA

000.000.0000 661-387-6090 www.localdealerweb.xx

Corona, CA

951-277-7620

LocalCA Dealer Fresno, 559-834-4420 Local dealer address 000.000.0000 Sacramento, CA 916-504-2300 www.localdealerweb.xx Lakeside, CA 619-441-3690

Local Dealer

With a wheel loade er this good d,

GO AHEADD AND BRAG A LIITTLE.

SanLocal Leandro, CAaddress dealer 510-357-9131

000.000.0000

Turlock, CA www.localdealerweb.xx 209-410-6710

DEALER LOGO www.localdealerweb.xx

Volv V olvo wheel loaders offer more — more power, more fuel efficiencyy,, more uptime and more profit. Spend less and earn more with a versatile, durable and capable Volvo machine on the job. Learn more at your nearest dealer location.

Page 46 • December 19, 2021 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

Infrastructure Spending May Exceed New Deal Investments INFRASTRUCTURE from page 1

of the total investment if both proposals become law, said the think-tank: The current House reconciliation version proposes roughly $500 billion in new infrastructure spending over 10 years, the organization noted. “Combined with IIJA, the federal government could be spending $160 billion above baseline for the next five years. That would push federal spending above New Deal investments in infrastructure — as measured by federal spending as a percentage of GDP — but likely to fall short of the historic federal peak around the late 1970s.” After non-stop lobbying for a broad infrastructure bill, the construction industry’s reaction to its signing was enthusiastic but cautious. ARTBA dubbed the IIJA “the most significant measure in more than 50 years to meaningfully address the condition and performance of the U.S. transportation network.” Dave Bauer, ARTBA CEO said Congress “demonstrated not only the importance of federal transportation infrastructure leadership, but that policymakers can find common ground and govern on matters of national concern.” Bauer saluted President Joe Biden, House members Nancy Pelosi and Steny Hoyer and Peter DeFazio; Senate members Chuck Schumer, Mitch McConnell, Tom Carper, Shelley Moore Capito, Kyrsten Sinema and Rob Portman for leading the effort, along with other members of Congress who voted for final passage. “Members of Congress have taken tangible action that will benefit every state and community across the nation,” Bauer said. Ward Nye, ARTBA chairman and CEO of Martin Marietta, was present at the White House, standing on behalf of the association and its members. “The bipartisan infrastructure law is a victory for all Americans,” he said. “Let’s get to work delivering transportation project outcomes that will boost the economy and make our roadways and railways safer.” Biden tapped Mitch Landrieu, former New Orleans mayor, to coordinate IIJA implementation. Working with experts, Landrieu will verify that jobs are created, the nation’s global competitiveness is strengthened, supply chains are opened and inflation is stanched. “Our work will require strong partnerships across the government and with state and local leaders, business and labor to create good-paying jobs and rebuild America for the middle class,” Landrieu said. “We will also ensure these major investments achieve the president’s goals of combating climate change and advancing equity,” Landrieu added. The National Asphalt Pavement Association (NAPA) has long supported a bi-partisan federal highway funding program, said Audrey Copeland, association president and CEO. “NAPA and like-minded organizations in the transportation construction industry, along with our engaged member companies and State Asphalt Pavement Association partners, have advocated for adequate and consistent federal highway funding for a very long time,” she said. “Asphalt pavement is already America’s most recycled product, and our industry is embarking on a bold vision toward net-zero carbon emissions,” she added. “We will, as we always have, do our part for our communities and our country, including our shared climate.” Generational Shift The IIJA is not another stimulus effort; it represents a generational shift in how and what types of projects get done,

noted Brookings. Federal agencies, including DOT, DOE and EPA, have to oversee the surge in funding, including administering new grants and designing new programs. “States and localities, from transportation departments to water utilities, have to identify and execute needed projects on the ground. And this federal, state and local coordination all comes amid continued challenges overseeing other expanded funding from the American Rescue Plan earlier this year,” said Brookings. Passage of a comprehensive infrastructure investment bill also has been a tier-one priority for the American Trucking Association (ATA), which believes IIJA will bolster highway safety, make long-overdue investments in roads and bridges and help grow and strengthen trucking’s workforce. ATA was represented at the White House, and association President and CEO Chris Spear praised the recognition by Congress that “roads and bridges are not political — we all drive them.” A majority in the House and Senate “realized this truth and did what’s right for the country, not themselves,” said Spear. “From farmers to truckers, the millions of hard-working people who make this country great won today.” He said that ATA members can finally see the fruits of their labor in the form of a 38-percent increase in road and bridge funding and an infusion of talent in the trucking sector’s workforce. “Those lawmakers who put their constituents before themselves have now cemented a lasting legacy that the American people will see, feel and use for many decades to come,” added Spear. The types of projects pursued, and the programs channeling resources to projects, will dictate the pace at which funds reach their targets, noted Brookings. State-of-good-repair projects obviously happen faster than new system expansions. “Funding in existing federal programs, including those distributed by formula, also tends to move faster than funding in new competitive grant programs, which involve new rulemaking,” wrote the think-tank. American Public Works Association (APWA) representatives also witnessed President Biden sign the IIJA into law. Like other industry leaders, APWA CEO Scott Grayson stressed how hard association members worked to see the act become reality. “From roads and bridges to better protecting communities against natural disasters to modernizing our water infrastructure network, this new law will deliver significant upgrades in every state and benefit every person,” he said. “The commitment of $550 billion in new federal spending over five years represents a generational improvement that still recognizes the need for local decision-making.” An Enormous Undertaking The American Association of State Highway and Transportation Officials (AASHTO) listed six priorities the Biden administration expects to follow during the legislation’s implementation: • Invest public dollars efficiently, avoid waste and focus on measurable outcomes for the American people; • Buy American and increase the competitiveness of the U.S. economy, especially via “Made-in-America” purchasing requirements, while also bolstering domestic manufacturing and manufacturing supply chains; • Create good-paying job opportunities for Americans by focusing on prevailing wages and the free and fair chance to join a union; • Invest public dollars equitably, including through the “Justice40 Initiative,” which seeks to make 40 percent of

the overall benefits from federal investments in climate and clean energy flow to disadvantaged communities; • Build resilient infrastructure that can withstand the impacts of climate change and helps combat the climate crisis; and • Effectively coordinate with state, local, tribal and territorial governments in implementing IIJA’s critical investments. According to AASHTO, USDOT Secretary Pete Buttigieg said the 24 projects that received $905 million via the Infrastructure for Rebuilding America discretionary grant program are the types of projects his agency aims to support through the IIJA. Projects slated to receive $1 billion worth of fiscal year 2021 discretionary grants via the new Rebuilding American Infrastructure with Sustainability and Equity program later this year would also exemplify the focus for infrastructure investments. “That’ll give you a sense, but we’ll have so much more to work with” via the IIJA, Buttigieg added. Jim Tymon, AASHTO executive director, said association members and state DOTs want to work with USDOT to implement the law as soon as possible. “State and local transportation agencies are eager to get to work on the multi-modal projects that will provide real benefits to the people of every community across the country.” AGC praised the IIJA for its benefits to the supply-chain system, saying because of the bill’s vote, state and local officials can invest in a more efficient network. “They will also be able to improve roads and bridges to make them safer and more reliable,” said Stephen Sandherr, CEO of the AGC. The American Society of Civil Engineers recently graded the country’s infrastructure system at a C-. “Metro areas will be able to better maintain and expand transit systems,” Sandherr added. “And water authorities will be able to further safeguard the quality of local drinking water, among other improvements funded by this bill. The measure also provides needed investments to make infrastructure more resilient to extreme weather events.” Michael Bellaman, president and CEO of Associated Builders and Contractors (ABC) lauded the bill for the opportunity it presents to modernize the nation’s infrastructure, and said ABC members are ready to bring the infrastructure system into the 21st century. But Bellaman tempered his praise, saying ABC is wary of some of the bill’s exclusionary provisions and Biden administration statements that could restrict the eligibility of American workers to compete for and participate in construction projects. And Doug Carlson, CEO of the National Utility Contractors Association (NUCA), said, “never before has the American utility construction industry been given by Congress resources of this magnitude to improve thousands of communities across America.” “An extraordinary achievement” is how Carlson described the passing of the bill and its level of funding. And like the rest of the construction industry, NUCA members are eager to get to work. “They’ll be the ones excavating trenches for new water and wastewater lines,” he said of his association’s membership. “They’ll be the ones replacing dangerous lead pipes to bring clean drinking water to communities across the nation. They’ll be building stormwater systems and new water treatment plants. They’ll also be laying new fiber-optic broadband cables, and helping to build modern ports, highways, railroads, and airports.”  CEG

Page 48 • December 19, 2021 • www.constructionequipmentguide.com • Mini & Compact Equipment Section • Construction Equipment Guide

Hummerbee Makes Good Impression On Mich.-Based Excavator Contractor

ROMCO Equipment www.romco.com 1519 W. Belt Line Road Dallas (Carrollton), TX 75006 214-819-4100 Austin, TX 512-388-2529 Buffalo, TX 903-322-5602 Carmine, TX 979-278-3570 Corpus Christi, TX 361-881-4891 Ft. Worth, TX 817-626-2288

At a recent equipment demonstration, Bob Best took notice of the stout, compact articulated loader busily feeding Bandit machines and was immediately impressed.

Rich Droste (L) of Hummerbee and Bob Best, owner of Best Excavation, with the Hummerbee 721R 4-wheel drive compact articulated loader.

At a recent equipment demonstration hosted by Bandit Industries near its headquarters in Remus, Mich., the manufacturer’s extensive line of tree chippers and stump grinders weren’t the only machines to catch the attention of Bob Best, owner of Best Excavation, based in Alma, Mich. Best took notice of the stout, compact articulated loader busily feeding the Bandit machines and was immediately impressed. As it turned out, the loader was on loan from another Michigan-based manufacturer, Hummerbee Rough Terrain Equipment. Brian Kulling, president of Hummerbee, also was on hand at the Bandit demo event and Best sought him out to learn more about the company and its compact articulated loader. Over the 35 years that Hummerbee has been in business, the company has gained a worldwide reputation as a premier manufacturer of rugged and reliable 4-wheel drive articulated forklifts for the beekeeping industry. With the rising popularity of compact machines in the construction, tree care, farming, forestry, landscaping and municipal maintenance industries, Hummerbee saw an opening for a U.S.-made, heavy-duty, compact articulated loader. Applying its decades of experience in the design, engineering and production of rough-terrain machines, the company set about the development of a telescopic, compact articulated loader that would bridge the gap between skid steer loaders / mini wheel loaders and full-sized wheel loaders. The goal was to design a compact loader that is costeffective yet rugged enough to meet the challenging demands of wide-ranging work applications. The result is the Hummerbee 721R, a 4-wheel drive compact articulated loader equipped with a 126-in. telescopic, dual- arm boom, 4,500-lb. tipping load, and is capable of getting around the job site at a speed of up to 14 mph. Powered by a Tier IV Final, 74 hp Kohler turbo diesel engine, Hummerbee’s articulated loader employs a 2-speed hydrostatic transmission with on-the-fly shifting. Best Excavation specializes in post construction site work to prepare projects for final landscaping. Much of the company’s work consists of backfilling around foundations and site development, material placement and leveling on projects within a 40-mi. radius of the company’s home base. Established in 1987 by Fred Best, he grew the company into what it is known as today. Best Excavation is now owned and managed by Fred’s nephew, Bob Best. As the new owner, he brings a new scope to the projects that Best

Excavation has been completing for more than 30 years. Best hopes to continue to find new ways to complete daily operations more efficiently and deliver the same quality service his uncle built the company around. That’s why the Hummerbee caught his attention, but will it fit the bill? Eager to test the new Hummerbee compact articulated loader in a real-world work application, Kulling readily agreed to provide Best Excavation one of its machines for an extended trial period. Best’s immediate impression when operating Hummerbee’s compact articulated loader was that getting accustomed to the machine was extremely easy. “The controls are like a cross between a wheel loader and a garden tractor,” said Best. “The forward / reverse rocker foot pedal, joystick controls and steering wheel are intuitive and very responsive.” Best also was impressed with how much weight the Hummerbee compact articulated loader could lift. The 721R can manage a 2,500- to 3,000-lb. operating load, depending on the tire size and counter weight package. “Unlike many machines of this size, the Hummerbee isn’t tippy or forward heavy at all,” he said. “The telescopic boom offers an advantage in loading a truck, providing access to the full truck bed as opposed to just the back half.” Best found that another advantage of the Hummerbee is that the location of the operator’s position, which is higher up, provides exceptional sight lines on the job site, making it safer to operate. Best also liked the fact that the Hummerbee is a wheeled loader as opposed to a track machine. “With a tracked machine, you have to watch how you turn to avoid tearing up the ground on a finished grade, we didn’t have that issue with the Hummerbee. And because it’s articulated, you can really operate in tight spots,” he said. A multitude of skid steer-style attachments are compatible with the Hummerbee compact articulated loader to equip the machine for a wide range of job functions. And the true, 21gpm auxiliary hydraulic oil flow extends the machines capabilities, which is a unique feature in the compact articulated loader world. “The Hummerbee articulated loader is easy to operate,” said Best. “An entry level person could jump on and go to work. It’s versatile and robust enough to meet the needs of professional contracting companies.” For more information, call Brian Kulling at 800/943-8677 or visit hummerbee.com.  CEG

Longview, TX 903-758-5576 Mercedes, TX 956-565-0100 San Antonio, TX 210-648-4600 Stephenville, TX 817-626-2288

Volvo Construction Equipment & Services www.vcesvolvo.com Bakersfield Bakersfield, CA 661-387-6090 Corona Corona, CA 951-277-7620 Fresno Fresno, CA 559-834-4420 Sacramento Sacramento, CA 916-504-2300 San Diego Lakeside, CA 619-441-3690 San Leandro San Leandro, CA 510-357-9131 Turlock Turlock, CA 209-410-6710

Construction Equipment Guide • Mini & Compact Equipment Section • www.constructionequipmentguide.com • December 19, 2021 • Page 49

WE’RE IN THE BUSINESS OF KEEPING YOU IN BUSINESS.

DISCOVER THE ASV GENUINE PARTS & SERVICE ADVANTAGE. ASV Genuine Parts are specifically engineered and guaranteed to maintain the integrity of your ASV machine. They’re designed, built, tested and re-tested to ensure equipment performance and reliability always stay at an all-time high – because less downtime for your machine means more uptime for you. Contact us now to learn more!

CLM Equipment Co. Inc.

FMI Equipment

Jet City Equipment

www.clmequipment.com

www.fmiequipment.com

www.jetcityequipment.com

3135 US Hwy 90 East Broussard, LA 70518 337-837-6693

11111 E Trent Avenue Spokane, WA 99206 509-927-4071

33345 SR20 Oak Harbor, WA 98277 360-675-4441

4851 E Napoleon Road Sulphur, LA 70663 337-625-5942

1947 Saint Street Richland, WA 99354 509-505-5997

10219 State Avenue Marysville, WA 98271 360-651-9079

2815 N Sam Houston Pkwy E Houston, TX 77032 281-598-2500

2713 Euclid Avenue Wenatchee, WA 98801 509-888-8181

Page 50 • December 19, 2021 • www.constructionequipmentguide.com • Mini & Compact Equipment Section • Construction Equipment Guide

TOUGH TASKS SEEM SMALL FROM HERE. The G-Series Skid Steers and Compact Track Loader are majorly tough customers, because tough customers like you helped design them. With your input, we were able to push the limits of durability, engine power, and fuel capacity in all the ways our customers need. And with fewer grease zerks and extended oil-change intervals compared to earlier models, servicing is even simpler than before. Available in three models, including a radial-lift machine, the G-Series can take down the biggest jobs — and your operating costs — all at the same time. To learn more, call or visit us today.

4RIVERS EQUIPMENT

YELLOWHOUSE MACHINERY

HONNEN EQUIPMENT CO.

DOGGETT HEAVY MACHINERY SERVICES

www.4riversequipment.com

www.yhmc.com

www.honnen.com

www.doggett.com

Colorado Springs, CO 719.475.1100 Frederick, CO 303.833.5900 Albuquerque, NM 505.884.2900 Farmington, NM 505.326.1101 Hobbs, NM 575.392.6923 El Paso, TX 915.598.1133

Broken Bow, OK 580-584-3222 Enid, OK 580-233-5000 Tulsa, OK 918-245-5926 McAlester, OK 918-423-2555

Amarillo, TX 806-335-1681 Dalhart, TX 806-884-4994 Lubbock, TX 806-748-4700 Abilene, TX 325-677-2291 Midland/Odessa, TX 432-580-3337 San Angelo, TX 325-651-3337

Denver, CO 303-287-7506 800-646-6636 Durango, CO 970-247-4460 Grand Junction, CO 970-243-7090 Ogden, UT 801-627-0049 Salt Lake City, UT 801-262-7441 St. George, UT 435-652-8003

Casper, WY 307-266-4474 Cheyenne, WY 307-316-9800 Gillette, WY 307-685-4288 Rock Springs, WY 307-382-5284 Idaho Falls, ID 208-523-9915

9111 North Freeway Houston, TX 77037 713-679-6700 Beaumont, TX 409-842-1754 Bryan, TX 979-823-1905 Corpus Christi, TX 361-289-0727 San Juan, TX 956-787-0001

Victoria, TX 361-570-6666

Lufkin, TX 936-634-8801

Alexandria, LA 318-442-0455

Monroe, LA 318-343-8787

Baton Rouge, LA 225-291-3750

Shreveport, LA 318-631-3090

Broussard, LA 337-837-9481

St. Rose, LA 504-466-5577

Covington, LA 985-893-3005

Tyler, TX 903-592-8900

Longview, TX 903-758-3326

Construction Equipment Guide • Mini & Compact Equipment Section • www.constructionequipmentguide.com • December 19, 2021 • Page 51

www.cpower.com 9200 Liberty Drive Liberty, MO 64068 816-781-8070 Wichita, KS 316-943-1231 Great Bend, KS 620-792-1361 Liberal, KS 620-624-7274 Woodward, OK 580-256-6014 Salina, KS 785-825-8291 Colby, KS 785-462-8211

Springfield, MO 417-865-0505 Joplin, MO 417-726-5373 Riverside, MO 816-415-6787 Wichita, KS 316-789-7370 Yukon, OK 405-324-2330 Maryland Heights, MO 314-427-4911 Liberty, MO 806-415-6700 Tulsa, OK 918-984-6565

Glenn B. Dorning www.gbdorning.com 1744 E. Holt Blvd. Ontario, CA 91761 909-983-2089

Page 52 • December 19, 2021 • www.constructionequipmentguide.com • Mini & Compact Equipment Section • Construction Equipment Guide

Cat’s New 304, 305 CR Mini Hydraulic Excavators Increase User’s Performance Built to deliver an improved customer experience, the new 4.4 ton Cat 304 and 5.5 ton Cat 305 CR next generation mini hydraulic excavators deliver more power to the pumps, higher bucket breakout forces and deeper standard digging depths to increase performance by up to 20 percent over their E2 series counterparts. Their grease intervals and extended filter service life, combined with common components throughout the line and flat, easy-to-replace side panels, deliver up to 10 percent lower owner and operating costs, according to the manufacturer. The new 304 and 305 CR models are the final machines to be reengineered to the Cat next generation mini hydraulic excavator line concept. From the 1.6 to 11 ton class models, all 17 to 20 Cat mini hydraulic excavators in the range (depending on region) offer common features and consistent controls layout to simplify training and operator adaptation.

machine control by allowing the operator to switch from conventional lever/foot-pedal steering controls to low-effort joystick operation. Two travel speed ranges and standard cruise control facilitate moving around the job site with minimum operator interaction. Meeting U.S. EPA Tier IV Final and EU Stage V emission standards, the turbocharged Cat C1.7 Turbo engine delivers higher power than the previous C2.4 engine. Standard auto idle, auto engine shutdown and efficient load-sensing hydraulics with variable displacement pump help to lower fuel usage at the site for more affordable operation. High main-relief pressures, coupled with flow rates, generates the hydraulic capacity for high digging and lifting forces and more efficient use of a range of attachments. Complete with quick-disconnect lines, the standard auxiliary system provides the choice of one-way, two-way or continuous flow.

New 304 Increases Stability Built with a new reduced radius design, the 304 features a narrow, 66.9-in. track width, 10 in. slimmer than the 304 E2, for more versatility and access to confined spaces. While narrower, the new 304 design increases performance, balance and stability. Its reduced radius allows for greater stability, both 360-degree and when traveling with loads, while its extra counterweight option takes the model to an even higher level of stability.

Next Generation Comfort, Savings Common to most Cat next generation mini hydraulic excavators, the sealed and pressurized cab enclosure is available with heating and/or air conditioning for all-weather climate control. The cab’s large glass areas plus skylight afford all-around visibility. The large display with advanced touchscreen option provides intuitive machine function control and easy monitoring of critical operating parameters. A canopy option is available in some regions. Daily maintenance checks for the 304 and 305 CR are quickly made from ground level through side doors. Expanded use of common parts throughout the line plus their damage-resistant exterior construction help to reduce parts inventory investment and lower repair costs. Increased service intervals mean these excavators spend more time on the job and less time in the shop. For more information, visit www.cat.com. 

Compact Performance of 305 CR The new engine on the Cat 305 CR excavator delivers nearly 9 percent greater power to increase machine performance. Hydraulic system improvements provide higher breakout forces — 49.2 kN (11,061 lbf) bucket, 28.3 kN (6,362 lbf) standard stick and 25.2 kN (5,665 lbf) long stick — to improve digging efficiency in hard rock applications. It also offers 5.6 in. deeper dig depths than the 305 E2, giving it more application flexibility. Its compact radius swing reduces overhang when working to the side, while its 78-in. track width and new extra counterweight option help to optimize stability and lift performance in confined spaces. Advanced Efficiency Both excavator models now offer an angle dozer blade option to optimize machine flexibility in backfilling and finish grading applications. In addition to offering ample above- and below-grade travel with standard float function for easy clean-up, the angle blade moves 45 degrees left or right of center. Increasing efficiencies and reducing operator interaction with final grading, angle blade movement is controlled by the right-hand joystick, while the left joystick handles machine drive. Tailoring machine weight to job requirements, interchangeable counterweight packages offer the balance between low ground pressure and lifting performance. The Cat Stick Steer System simplifies

While narrower, the new 304 design increases performance, balance and stability. Its reduced radius allows for greater stability, both 360degree and when traveling with loads, while its extra counterweight option takes the model to an even higher level of stability.

OKLAHOMA TERRITORY CONSTRUCTION EQUIPMENT www.oklahomaterritoryequipment.com Oklahoma City, OK 405-917-9191 Tulsa, OK 918-835-7200

Garton Tractor Inc. www.gartontractor.com 2400 N Golden State Blvd. • Turlock, CA 95382 209-632-3931 Fairfield, CA • 707-425-9545 Merced, CA • 209-726-4600 Modesto, CA 95356 • 209-538-0911 Newman, CA • 209-862-3760 Santa Rosa, CA • 707-586-1790 Stockton, CA 95206 • 209-948-5401 Tulare, CA 93274 • 559-686-0054 Ukiah, CA 95482 • 707-468-5880

CLM EQUIPMENT CO. INC. www.clmequipment.com Lafayette, LA 337-837-6693 Lake Charles, LA 337-625-5942 Houston, TX 281-598-2500

BANE MACHINERY INC. www.banemachinery.com Dallas, TX 800-594-2263 Ft. Worth, TX 800-601-2263 Tyler, TX 800-594-2200

COLUMBIA WESTERN MACHINERY Columbiawesternmachinery.com 11125 SW Tonquin Road Sherwood, OR 97140 503-454-0902

Construction Equipment Guide • Mini & Compact Equipment Section • www.constructionequipmentguide.com • December 19, 2021 • Page 53

Cooper Equipment Co. www.cooperequip.com 201 Commerce Blvd. Georgetown, TX 78626 512-930-5151

TRI-WEST TRACTOR, INC. www.tri-westtractor.com 6281 Southfront Road Livermore, CA 94551 925-455-8200

Dealer Imprint

Westrax Machinery www.westraxmachinery.net

Shafer Equipment Company, Inc.

19618 S. Susana Rd. Rancho Ar ea Dominguez, CA 90221 800-411-4717

www.shaferequipmentco.com 955 Greg Street • Sparks, NV 89431 775-235-4069

19885 Temescal Canyon Rd Corona, CA 92881 800-411-4717

APCO EQUIPMENT www.apcoequipment.com 3432 N 5th Street North Las Vegas, NV 89032 800-574-4089

BEARD EQUIPMENT CO. www.beardequipco.com 4509 I-20 • Midland, TX 79706 432-694-4530

611 N. Golden Key St. Gilbert, AZ 85233 602-397-8173

Rasmussen Equipment Co. www.raseq.com 3333 West 2100 South West Valley City, UT 84119 801-972-5588

Page 54 • December 19, 2021 • www.constructionequipmentguide.com • Mini & Compact Equipment Section • Construction Equipment Guide

THE TORO® DINGO® TXL 2000 DOES THE WORK OF SEVERAL MACHINES IN ONE. Dig below grade, reach over obstacles and extend your workiing range with the powerful telescoping arms. Enjoy

FMI Equipment

360˚ visibility from the stand-on

www.fmiequipment.com

operator platform. You can even use most skid steer and compact track

Toro® Dingo® TXL 2000

loader attachments with the universal

WITH TELESCOPING ARMS

mounting plate. Call 1-800-344-8676, option 1, to find a dealer near you.

OUT. T STANDING.

11111 E Trent Avenue Spokane, WA 99206 509-927-4071 1947 Saint Street Richland, WA 99354 509-505-5997

Bobcat Debuts Two Reimagined Toolcat Utility Machines Bobcat has refreshed its utility work machine lineup with the all new UW53 and UW56 Toolcat utility work machines. These two models come equipped with a variety of enhancements — both inside and outside the cab. Replacing the previous models of the Toolcat utility work machine lineup, the UW53 and UW56 have the capability for increased attachment versatility, allowing operators to easily turn their equipment into multi-purpose hauling, lifting, mowing, towing and loading machines, according to the manufacturer. These new models have totally redesigned LED lighting, providing increased light dispersion and intensity using less power. The embedded road lights are integrated within the front fenders (instead of on the bottom of the front windshield), providing optimal protection and unobstructed illumination for better visibility in all directions. The rear work lights also have changed to LED, to optimize for better light dispersion. The newly updated dual-drive response system has been enhanced to provide smoother acceleration and deceleration, automatically recalling drive response settings. The first setting provides a smooth,

responsive traction for driving between tasks, and the second setting changes the drive system to a more aggressive response when operating in low range to maintain hydraulic and traction power for uninterrupted work. A new optional rear-view camera gives operators ideal visibility for tasks that require regular machine maneuvering. The rear-frame location of the camera provides

an unobstructed view for connecting a ball hitch (UW56 model only). In addition to these performance enhancements, operators will find several significant comfort updates, including a totally redesigned interior with an integrated 5-in. display, enhanced ergonomics, component placements and storage spots all within easy access. All controls are in one place for increased operational control, including all

The newly updated dual-drive response system has been enhanced to provide smoother acceleration and deceleration, automatically recalling drive response settings.

secondary functions. For enhanced uptime and serviceability, operators will find a larger fuel filter, increased operating time between required oil filter changes, increased corrosion protection and fender shape/material, larger incab access points and improved wiring harness. For more information, visit https://www.bobcat.com/utility-products/toolcat/features. 

Replacing the previous models of the Toolcat utility work machine lineup, the UW53 and UW56 have the capability for increased attachment versatility, allowing operators to easily turn their equipment into multi-purpose hauling, lifting, mowing, towing and loading machines, according to the manufacturer.

Construction Equipment Guide • Mini & Compact Equipment Section • www.constructionequipmentguide.com • December 19, 2021 • Page 55

WORLD’S SMALLEST BACKHOE NOW WITH TRACKS – JCB-1CXT

Max Dig Depth: 10 ft 1 in / Gross Engine Power 49 HP / Loader Bucket Breakout: 1,466 lb JCB 1 CXT, a TRACKED BACKHOE is a versatile machine, offering skid-steer and mini excavator performance in one package. The 1CXT provides superior maneuverability, an optional handheld tool auxiliary, as well as a universal quick hitch that is compatible with most of your skid steer attachments. Standard full cab with integrated heating & air-conditioning. Due to its compact size and under 10,000 lbs weight, the 1 CXT is easy to tow in a trailer without a CDL (where local regulations allow). NO DPF / DEF AFTERTREATMENT. Operators environment friendly with easy to use controls and all daily checks and greasing can be carried out at ground level on a JCB backhoe. To learn more about JCB 1CXT, visit www.jcb.com/en-us/products/backhoe-loaders/1cxt

/ /JCBNA

www.ProConJCB.com

www.swjcb.com

461 Pioneer Place Las Cruces, NM 88005 1-844-JCB-IRON

2935 Lincoln Road Las Vegas, NV 89115 702-432-2200

5050 East 58 Avenue Commerce City, CO 80022 1-844-JCB-IRON 2240 W. Buckeye Road Phoenix, AZ 85009 1-844-JCB-IRON

@JCBNA

w w.jcb.com .jcb.com JCBNA www

Cisco Equipment www.cisco-equipment.com 620 N. Bell Street San Angelo, TX 76903 800-496-0271

1706 S 1st Street Artesia, NM 88210 575-748-1314

2707 Slaton Hwy Lubbock, TX 79404 806-745-9595

520 SE Loop 338 Odessa, TX 79762 432-367-9181

Terms & Conditions: Pictures shown with optional accessories. For towing policy please consult with your local state transportation office. Offers may change without notice and may not be combined. Additional terms and conditions may apply, please contact your local JCB dealer for details. JCB dealer reserves the right to withdraw, alter or decline any product from sale or any offer without prior notice. Price, if shown, does not include government fees, taxes, dealer freight/preparation, dealer document preparation charges or any finance charges (if applicable). Final actual sales price will vary depending on options or accessories selected.

Page 56 • December 19, 2021 • www.constructionequipmentguide.com • Mini & Compact Equipment Section • Construction Equipment Guide

Ditch Witch RT70 Ride-On Trencher Maximizes the Operator Experience To enhance utility and the fiber contractor’s experience, while tackling tough jobs on tight schedules, Ditch Witch has introduced the RT70 ride-on trencher. The newly designed trencher is equipped with features that increase operator comfort and visibility, helping to boost efficiency and profitability on the job site, according to the manufacturer. For example, the ergonomically designed operator station features an open layout with a 120-degree swivel seat, more leg room and intuitive controls. This enhanced visibility gives operators a full view of the machine — from front tire to back tire and the attachment — helping operators of any experience level increase productivity. The RT70 also includes a cooling fan to reduce temperature levels in the operator station by moving hot, uncomfortable exhaust out of the side of the machine rather than toward the operator like traditional fans. This helps keep workers safer and more comfortable during long days. “At Ditch Witch, we understand the challenges that electric and fiber contractors face daily,” said Steve Seabolt, product manager, ride-on tractors, Ditch Witch. “The RT70 is compact and maneuverable, yet powerful. This new unit, with its unique features, will allow the operator to tackle

tough jobs in tight conditions.” Powered by a 72 hp Yanmar Tier IV Stage V compliant diesel engine, and built with a narrow footprint of 73-in. wide, the RT70 rubber-tire trencher can handle heavy-duty jobs and still easily maneuver around tight job sites, corners and cul-de-sacs with ease. This makes it the perfect go-to trencher to take on even the toughest jobs, according to the manufacturer. It also is available with crab and coordinated steering modes, which allows operators to turn the machine with a steering wheel instead of using two separate levers. This makes it easier to use and frees them up to focus on other parts of the job. The machine’s modular design features a single base unit with the option to move from tires to tracks. And with different attachments, plus a variety of optional add-ons, operators can endlessly reconfigure their machine throughout its lifecycle to customize it for specific job site needs. The RT70 is built to increase operator productivity with daily maintenance points in one easy-to-access location and a single-piece, easy-open hood. Fast and simple maintenance means that operators can spend their valuable time where it matters most — on the job site. For more information, visit ditchwitch.com/ride-on/rt70. 

Toro’s Dingo TX 700 Ideal in Tight Spaces Toro has added the Dingo TX 700 to its already extensive Dingo line-up. Due to the Dingo TX 700’s small size and powerful punch, it’s the ideal machine for both homeowners and contractors working within the confines of tight spaces. It packs 700 pounds of rated operating capacity into its small footprint, bringing Toro-level power to everything it touches, according to the company. “The compact size and flexibility of the Dingo TX 700 is bound to be a game-changer for operators,” said Kyle Cartwright, marketing manager at Toro. “The fact that it’s small, but incredibly capable, increases the applications for the Dingo TX 700 on the job site. This Dingo has the potential to be the compact go-getter of the operation.” Featuring Dingo TX 1000 traction controls and a dedicated stand-on platform, the Dingo TX 700 is easy-to-use and boasts increased comfort and visibility. Even if the buyer is new to oper-

ating heavy machinery, it will quickly become second nature, the company said. The versatility of Dingos, or compact utility loaders, is well-known — and the Dingo TX 700 is no different. In fact, its small size further increases versatility by allowing it to reach areas other Dingos may not. It’s also compatible with dozens of attachments, meaning the machine can be used for a wide range of jobs. Attachments include multiple types of buckets, adjustable forks, a grapple, leveler, utility blade and more. Completing more work using fewer machines is a major advantage, plus, the Dingo TX 700 doesn’t require as much storage space as its larger counterparts. It’s easy on turf, too. The Dingo TX 700 is available in both narrow track and wide track configurations — the wide track option is equipped with the industry tested Camso track system. The system features a less aggressive

tread pattern that’s gentle on turf and minimizes damage, perfect for keeping pristine lawns intact. The new Dingo TX 700 will be available starting mid-year 2022. For more information, visit www.toro.com. 

Kirby-Smith Machinery www.kirby-smith.com 6715 W. Reno Ave Oklahoma City, OK 73127 800-375-3339 McAlester, OK 918-310-1550 Tulsa, OK 800-375-3733

Amarillo, TX 800-283-1247 Lubbock, TX 866-289-6087 Odessa, TX 877-794-1800

Abilene, TX 877-577-5729

Tri-West Tractor, Inc. www.tri-westtractor.com 6281 Southfront Road Livermore, CA 94551 925-455-8200

Ditch Witch of East Texas www.witchequipment.net 7717 Highway 69 Tyler, TX 75706 903-592-6226

Ditch Witch of Arizona www.ditchwitchaz.com 4028 S. 36th St. Phoenix, AZ 85040 602-437-0351 Tucson, AZ 520-579-0261

EquipmentShare www.equipmentshare.com 295 S Redwood Rd North Salt Lake, UT 84054 385-308-5516 2590 Main Street Chula Vista, CA 91911 619-510-6825 412 E Gowan Road North Las Vegas, NV 89032 725-221-0051

Featuring Dingo TX 1000 traction controls and a dedicated stand-on platform, the Dingo TX 700 is easy-to-use and boasts increased comfort and visibility.

Construction Equipment Guide • Mini & Compact Equipment Section • www.constructionequipmentguide.com • December 19, 2021 • Page 57

Waukesha-Pearce Industries, Inc.

Garton Tractor Inc.

Power MotiveCorporation

www.wpi.com

www.gartontractor.com

www.powermotivecorp.com

12320 South Main St. Houston, TX 77035 713-551-0506 Tomball, TX 281-351-9016 Corpus Christi, TX 361-884-8275 San Antonio, TX 210-648-4444

Beaumont, TX 409-721-5305 Edinburg, TX 956-386-0107 Austin, TX 512-251-0013 Buffalo, TX 903-322-7150

4088 Russell Road Fairfield, CA 94534 707-425-9545 Santa Rosa, CA 707-586-1790 Ukiah, CA 95482 707-468-5880

DENVER HEADQUARTERS 5000 Vasquez Blvd. Denver, CO 80216 303-355-5900

Milliken 970-587-1188

Colorado Springs 719-576-5541

Cheyenne 307-634-5149

Grand Junction 970-241-1550

Durango 970-259-0455

Nueces Power Equipment www.nuecespower.com 4697 FM 1516 N Converse, TX 78109 210-310-0066 7667 N Sam Houston Pkwy Humble, TX 77396 713-247-0066

Page 58 • December 19, 2021 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

Takeuchi-US Hosts Family Fun Day, Food Drive Raises $4K for Local Bank CISCO EQUIPMENT www.cisco-equipment.com 1706 South 1st Street, Artesia, NM 88210 575-748-1314 Odessa, TX • 432-550-9181 Lubbock, TX • 806-745-9595 San Angelo, TX • 325-653-2121

NED - TEXAS (Formerly Four Seasons Equipment) www.NEDealers.com Houston, TX • 800-234-5007 Dallas TX • 866-270-1700

Takeuchi-US President Jeff Stewart presents a check to staff at the Banks Jackson Food Bank in Commerce, Ga.

On Nov. 12, Takeuchi-US employees, including President Jeff Stewart, presented the Banks Jackson Food Bank in Commerce, Ga., with enough food for 200 Thanksgiving dinners and an extra $2,550 to buy additional turkeys to feed even more needy families. This generous donation, worth a total of about $4,000, started out as a simple accompaniment to a fun company event and morphed into something far more meaningful. In October, Takeuchi hosted employees and their families for Family Fun Day. Leading up to the event, Takeuchi had a food drive to collect both food and monetary donations for the Banks Jackson Food Bank. At Family Fun Day, approximately 200 adults and children enjoyed a pumpkin patch, food from local food trucks and numerous activities including bouncy houses, pumpkin painting, an egg race, a magician, corn hole games, a photo-

booth, a giant “Jenga” game and hayrack rides. One particularly popular event was “Meringue the Manager,” where employees paid money to throw whipped cream pies at their managers, raising an additional $600 for the food bank. Takeuchi then generously agreed to double whatever employees raised, which resulted in the total donation of 200 Thanksgiving dinners and $2,550 in additional funds. “We wanted to host Family Fun Day for our employees so that they could bond after a long year apart following the pandemic,” said Stewart. “It was also a great way for us to come together and do something for our community. I’m proud of how our employees stepped up and raised a significant amount of money that will help local families enjoy Thanksgiving dinners that they wouldn’t have otherwise been able to afford.” For more information, visit www.takeuchi-us.com. 

NUECES POWER EQUIPMENT www.nuecespower.com 7510 IH-37 Access Rd., Corpus Christi, TX 78409 361-289-0066 Laredo, TX • 956-725-0066 San Antonio, TX • 210-310-0066 San Benito, TX • 956-361-0066 Victoria, TX • 361-576-0066 El Paso, TX • 915-541-0066

PORTER GROUP USA www.portergroupusa.com 13013 Temescal Canyon Rd, Corona, CA 92883 951-674-9999 Pacoima, CA • 818-834-0102 Newark, CA • 510-713-7368

MECOM EQUIPMENT www.mecomequipment.com 4546 N Wilson Way, Stockton, CA 95205 209-466-5135

JET CITY EQUIPMENT www.jetcityequipment.com 33345 SR 20, Oak Harbor, WA • 360-675-4441 Marysville, WA • 360-651-9079 Wenatchee, WA • 509-888-8181

R & S INDUSTRIES, INC. www.rsindinc.com 951 CR G, Clovis, NM 88101 575-769-8659

(L-R): Jason Menter, Cam Reiff, Angy Lamb, Elise McQuade, Carrie Stewart and Jeff Stewart with food donated by Takeuchi-US to help the Banks Jackson Food Bank of Commerce, Ga., provide 200 needy families with Thanksgiving meals.

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • December 19, 2021 • Page 59

Get an “A” with Hyundai

Hyundai Construction Equipment is excited to announce the launching of our new A-series machines. Along with a new look, these machines are packed full of standard new features and benefits to get the job done efficiently. • Cummins Performance Series Engines Stage V emissions compliant engines • No EGR (Exhaust Gas Recirculation) Improved fuel consumption • Smart Power Mode 3-5% fuel savings in high load work • New engine hood design Enhanced visibility to rear of machine

More standard features. More value.

www.hceamericas.com To learn more about the what the new Hyundai A-Series machines can offer your business, contact your Hyundai dealer today.

Page 60 • December 19, 2021 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

Teaming Up…

Doosan’s New ‘Transparent Bucket’ Ritchie, SmartEquip System Offers Safety for Operators DOOSAN from page 14

DX50Z-7 Mini-Excavator Specs include: • Horsepower: 48.8 hp • Operating Weight: 12,121 lbs. • Maximum Digging Depth: 11 ft. 5 in. • Maximum Digging Reach (ground): 19 ft. • Maximum Loading Height: 12 ft. 6 in.

Doosan’s new DX350LC7 crawler excavator.

Ritchie Bros. announced that it has completed its acquisition of SmartEquip, a technology platform that supports customers’ management of the equipment lifecycle and integrates parts procurement with both OEMs and dealers. “This acquisition expands our solution set and furthers our goal of providing the best customer experience as we transition from a traditional auctioneer to a global marketplace for insights, services, and transaction solutions,” said Ann Fandozzi, chief executive officer, Ritchie Bros.

DX140LCR-7 Crawler Excavator Specs include: • Horsepower: 115 hp • Operating Weight: 35,424 lbs. • Maximum Digging Depth: 19 ft. 8 in. • Maximum Digging Reach (ground): 28 ft. • Maximum Loading Height: 23 ft. 3 in. DX350LC-7 Crawler Excavator Specs include: • Horsepower: 286 hp • Operating Weight: 79,366 lbs. • Maximum Digging Depth: 24 ft. 9 in. • Maximum Digging Reach (ground): 36 ft. • Maximum Loading Height: 23 ft. 6 in. DL200-7 Wheel Loader Specs Include: • Horsepower: 142 hp • Operating Weight: 26,559 lbs. • Bucket Capacity, heaped: 2.6 cu. yds. • Static Tipping Load, full turn: 19,705 lbs. • Dump Height, 45 degrees: 9 ft. 1 in. • Dump Reach, 45 degrees: 3 ft. 4 in. DL220-7 Wheel Loader Specs include: Doosan’s DL250-7 wheel loader.

to Make Iron Parts Procurement Easier

• Horsepower: 160 hp • Operating Weight: 29,098 lbs. • Bucket Capacity, heaped: 3 cu. yds. • Static Tipping Load, full turn: 20,461 lbs. • Dump Height, 45 degrees: 9 ft. 3 in. • Dump Reach, 45 degrees: 3 ft. 6 in. DL250-7 Wheel Loader Specs include: • Horsepower: 172 hp • Operating Weight: 30,528 lbs. • Bucket Capacity, heaped: 3.3 cu. yds. • Static Tipping Load, full turn: 21,134 lbs. • Dump Height, 45 degrees: 9 ft. 2 in. • Dump Reach, 45 degrees: 3 ft. 6 in. 

“Ritchie Bros. is a perfect partner for us and our team is very excited to take the next growth step together.” Bryan Rich SmartEquip

“SmartEquip will enable us to offer asset-specific, fulllifecycle parts and service support to customers on behalf of our dealer and OEM partners.” SmartEquip is a multi-manufacturer platform that provides customers with real-time service and diagnostic support, dynamically customized, via serial number, to each asset in their fleet, as well as enabling the electronic procurement of parts from OEMs and their dealers. The company supports approximately $1 billion in annual transaction volume with more than 600 OEM brands, on behalf of fleet locations across North America, Europe and the Asia Pacific. SmartEquip has 60 employees and will continue to operate as a standalone business and maintain its physical presence in Norwalk, Conn., for the foreseeable future. “Ritchie Bros. is a perfect partner for us and our team is very excited to take the next growth step together,” said Bryan Rich, SmartEquip’s executive chairman. “Through Ritchie Bros.’ global customer base, this merger will accelerate SmartEquip’s ability to support its rapidly growing footprint across our joint global marketplaces and customer base. We can’t wait to get started.” Under the terms of the transaction, Ritchie Bros. has acquired 100 percent of the equity of SmartEquip for approximately $175 million subject to adjustment. For more information about Ritchie Bros., visit RitchieBros.com. 

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • December 19, 2021 • Page 61

Attention Contractors! Post Your Wanted To Buy Listings FREE! Here’s How! List Your Wanted Items. If you would like to place your Wanted To Buy listings on our website for inclusion in our newsletters, simply visit: www.ConstructionEquipmentGuide.com/wanted-to-buy and enter your listings. Inappropriate or Sale Ads will be Deleted WANTED (US): CATERPILLAR WHEEL LOADERS, ALL MODELS. WE NEED TO BUY CAT USED WHEEL LOADER 916,926,936,950B/E,966E/D/F, 970F, 980C,980F ALSO CAT MOTOR GRADERS 140G,12G/H, 14G/H, 140H, AND 14M. IF ANY OF THEM ARE AVAILABLE PLEASE LET US KNOW THANKS. EMAIL: IKCEQUIPMENTS@GMAIL.COM –––––––––––––––––––––––––––––––– WANTED (WORLDWIDE): HITACHI EX450 LC-5 EXCAVATORS. WE ARE LOOKING FOR USED HEAVY CONSTRUCTION MACHINES. PLEASE OFFER US FOLLOWING MENTION MACHINES & EMAIL US DETAILS WITH PICTURES CATERPILLAR MOTOR GRADERS 140G CATERPILLAR WHEEL LOADERS 950B, 950E, 966E, 966F, 966FII, 970F, 980F HITACHI EXCAVATORS EX200, EX200LC, EX270LC, EX400, EX400LC, EX300LC, EX330LC-5, EX450LC-5, EX400-5, EX60WD, EX100WD. JOHN DEERE 495D, 595D. EMAIL: NAQIB_KHANINTRCO@ HOTMAIL.COM PHONE: +923332316587 –––––––––––––––––––––––––––––––– WANTED (US): CATERPILLAR 950B WHEEL LOADERS - LOOKING TO BUY CAT WHEEL LOADERS 950B, 950E, 966E, 966F, 966F II, 970F, 980F. EMAIL: NAQIB_KHAN73@YAHOO.COM PHONE: +923333298751 –––––––––––––––––––––––––––––––– WANTED (WORLDWIDE): CATERPILLAR WHEEL LOADERS, ALL MODELS. WE ARE INTERESTED IN BUYING CAT USED WHEEL LOADERS 916,926,936,950B/E,966E/D/F, 970F, 980C,980F ALSO CAT MOTOR GRADER 140G AND 140H. (RUNNING OR NONRUNNING MACHINES). EMAIL: AHMED@IUKANDCO.COM PHONE: +923003695360 –––––––––––––––––––––––––––––––– WANTED (US): CATERPILLAR 966F II WHEEL LOADER. EMAIL: ILYAS.MTCPK@GMAIL.COM; PHONE: +923322489350 –––––––––––––––––––––––––––––––– WANTED (US): CATERPILLAR EXCAVATORS, ALL MODELS; LOOKING FOR SEVERAL CAT 330DL, 336DL, 336EL EXCAVATORS UNDER 10,000 HOURS AND WHOLESALE PRICED. EMAIL: LJEQUIPMENT3@GMAIL.COM; PHONE: 1-3309873508 –––––––––––––––––––––––––––––––– WANTED (US): HITACHI EXCAVATORS, ALL MODELS; LOOKING FOR OLDER HITACHI EXCAVATORS AND CAT WHEEL LOADERS, IN GOOD RUNNING CONDITION OR NON-RUNNING MACHINES. EMAIL US TO DISCUSS. EMAIL: IKCEQUIPMENTS@GMAIL.COM –––––––––––––––––––––––––––––––– WANTED (US): HITACHI EX450 EXCAVATORS - NEED TO BUY HITACHI EX 400 AND 450 SIZES EXCAVATORS. EMAIL: IUKANDCO@YAHOO.COM ––––––––––––––––––––––––––––––––

WANTED (WORLDWIDE): ALL MODELS CAT WHEEL LOADERS - WE NEED CAT USED WHEEL LOADERS 916,926,936,950B/E,966E/D/F, 970F, 980C,980F. IF ANY OF THEM ARE AVAILABLE PLEASE LET ME KNOW. EMAIL: AHMED@IUKANDCO.COM; PHONE: +923003695360 –––––––––––––––––––––––––––––––– WANTED (US): ALL MODELS HITACHI EXCAVATORS – WE NEED TO BUY HITACHI EXCAVATORS ZX 200-1, ZX 330, ZX 450, ZX 650, ZX 850 EX 270-1, EX 300-1, EX 400-1 AND EX 450-5. ALSO KOMATSU EXCAVATORS PC400, KOMATSU PC 450-6, KOMATSU PC 7506. IF ANY OF THEM ARE AVAILABLE PLEASE LET US KNOW, THANKS. EMAIL: EDDIE.SIDDIQUI3@GMAIL.COM –––––––––––––––––––––––––––––––– WANTED (US): LOOKING TO BUY THESE MODELS OF USED CATERPILLAR WHEEL LOADER 950B, 950E, 966E, 966F ,966F-II. EMAIL: ILYAS.MTCPK@GMAIL.COM; PHONE: +923322489350 –––––––––––––––––––––––––––––––– WANTED (US): ALL MODELS KOMATSU WHEEL LOADERS - WE NEED TO BUY KOMATSU WHEEL LOADER WA-600-3, WA-600-6, WA-30, WA-40, WA 50. IF YOU HAVE AVAILABLE, PLEASE LET US KNOW. EMAIL: IKCEQUIPMENTS@GMAIL.COM –––––––––––––––––––––––––––––––– WANTED (WORLDWIDE): CATERPILLAR 972H WHEEL LOADER. EMAIL: PONTO2002EG@YAHOO.COM –––––––––––––––––––––––––––––––– WANTED (WORLDWIDE): ALL MODELS HITACHI EXCAVATORS - WE ARE INTERESTED IN BUYING JOHN DEERE EXCAVATORS 790, 495 & 595 AND HITACHI EXCAVATORS EX 270-1, EX 270-5, EX 300-1, EX 400-1 AND EX 450-5. EMAIL: AHMED@IUKANDCO.COM; PHONE: +923003695360 –––––––––––––––––––––––––––––––– WANTED (WORLDWIDE): ALL MODELS CATERPILLAR WHEEL LOADERS - WE ARE INTERESTED TO BUY CAT USED WHEEL LOADER 916, 926, 936, 950B/E, 966E/D/F, 970F, 980C, 980F. IF AVAILABLE PLEASE EMAIL US: IKCEQUIPMENTS@GMAIL.COM; PHONE: +923003695360 –––––––––––––––––––––––––––––––– WANTED (US): ALL MODELS WAIN ROY BUCKETS - LOOKING FOR 24", 30" OR 36" BACKHOE BUCKETS. I HAVE A CATERPILLAR 420D EQUIPPED WITH THE ONE PIN CATERPILLAR QUICK EXCHANGE SYSTEM. CATERPILLAR, WAIN-ROY OR SIMILAR BUCKETS WOULD BE FINE. THE CLOSER TO SOUTHWEST FLORIDA, THE BETTER, BUCKET WILL NEED TO BE SHIPPED. PLEASE SEND PHOTOS AND PRICES. THANKS IN ADVANCE. EMAIL: TWOPETIES@AOL.COM; PHONE: 239-440-4254 ––––––––––––––––––––––––––––––––

WANTED (WORLDWIDE): ALL MODELS HITACHI EXCAVATORS - LOOKING TO BUY HITACHI EXCAVATOR EX200, EX200LC, EX270LC, EX330LC-5, EX400LC, EX450LC-5. OFFER AVAILABLE EQUIPMENT AND GOOD PRICE. EMAIL: ELROYFITZGERALDSALES@ GMAIL.COM –––––––––––––––––––––––––––––––– WANTED (WORLDWIDE): ALL MODELS CATERPILLAR MOTOR GRADERS - WE ARE INTERESTED TO BUY CAT MOTOR GRADERS 140G,12G/H, 14G/H, 140H, AND 14M. IF ANY OF THEM ARE AVAILABLE PLEASE LET ME KNOW THANKS. EMAIL: IKCEQUIPMENTS@GMAIL.COM; PHONE: +923003695360 –––––––––––––––––––––––––––––––– WANTED (MD): KOMATSU ANY KOMATSU PC100-5,120-5,150-5,200-5,220-5,3005 EXCAVATOR EMAIL: MIKE@3MEQUIPMENT.COM; PHONE: 240-910-0877 –––––––––––––––––––––––––––––––– WANTED (WORLDWIDE): LOOKING TO BUY CATERPILLAR WHEEL LOADERS 950B, 950E, 966E, 966F, 966F II, 970F, 980F. OFFER AVAILABLE EQUIPMENT AND GOOD PRICE. EMAIL: NAQIB_KHAN73@YAHOO.COM –––––––––––––––––––––––––––––––– WANTED (WORLDWIDE): LOOKING TO BUY HITACHI EXCAVATOR EX200, EX200LC, EX270LC, EX330LC-5, EX400LC, EX450LC-5. OFFER AVAILABLE EQUIPMENT AND GOOD PRICE. EMAIL: NAQIB_KHANINTRCO@ HOTMAIL.COM –––––––––––––––––––––––––––––––– WANTED (US): ALL MODELS VERMEER TRENCHING / BORING / CABLE PLOWS - M495 VERMEER VIBRATORY PLOW. NEED WHOLE MACHINE WHETHER IT RUNS OR FOR PARTS. EMAIL: JOHN@PIONEERTREE.COM; PHONE: 612-860-5327 –––––––––––––––––––––––––––––––– WANTED (NE): ALL MODELS ATLAS COPCO BREAKERS / HAMMERS. EMAIL: JAKE.SMITH41@YAHOO.COM; PHONE: 402-350-3280 –––––––––––––––––––––––––––––––– WANTED (US): HITACHI EX270LC EXCAVATOR. EMAIL: ILYAS.MTCPK@GMAIL.COM; PHONE: +923322489350 –––––––––––––––––––––––––––––––– WANTED (WORLDWIDE): CATERPILLAR 988F WHEEL LOADER; USED CATERPILLAR 988F, IDEALLY MANUFACTURED IN YEARS 1993-1995 AND IN WORKING CONDITION. EMAIL: BRIAN@CANDEVINC.COM ––––––––––––––––––––––––––––––––

WANTED (US): WE ARE LOOKING TO BUY ANY USED CONSTRUCTION EQUIPMENT IN ANY CONDITION (RUNNING GOOD, DOESN’T WORK, HAVE AN ISSUE, HIGH HOURS, ROUGH SHAPE, DISMANTLED MACHINE) LIKE (WHEEL LOADERS, CRAWLER LOADERS, DOZERS, EXCAVATORS, MOTOR GRADERS, LOADER BACKHOES AND SKID STEERS). ALSO WE BUY OLD CAT MACHINES. EMAIL: GCESMARKETING8@GMAIL.COM; PHONE: 657-236-7399 –––––––––––––––––––––––––––––––– WANTED (US): CASE 1150E CRAWLER DOZER, MUST HAVE WINCH AND POSSIBLY BRUSH RAKE. EMAIL: MTRAY10@GMAIL.COM –––––––––––––––––––––––––––––––– WANTED (US): A FRONT BUCKET SINGLE DUMP CYLINDER FOR A JOHN DEERE 415B LOADER/BACKHOE.. MACHINE SERIAL NUMBER 004286…JD PART NUMBER RE13064..SAME PISTON AS A 410. EMAIL: DEANDRS@VWERIZON.NETR; PHONE: 610-417-5123 –––––––––––––––––––––––––––––––– WANTED (WORLDWIDE): NEED FOLLOWING CAT WHEEL LOADERS: 950B, 950E, 966E, 966F, 966FII, 970F, 980F. OFFER AT GOOD PRICE. EMAIL: HIDAYATMASOOD@GMAIL.COM –––––––––––––––––––––––––––––––– WANTED (WORLDWIDE): LOOKING TO BUY HITACHI EXCAVATORS EX200, EX270, EX270LC, EX400LC, EX450LC-5. EMAIL: FAIZKHAN0316@GMAIL.COM; PHONE: +923332925103 –––––––––––––––––––––––––––––––– WANTED (WV): NELSON 6000 WELDERS - LOOKING FOR NELSON DUAL GUN SYSTEM WITH GEN SET AND TRAILER, AND/OR PRO-WELD DUAL GUN ARC 3000 MACHINE. EMAIL: WEH@ TRIANGLEINCORPORATED.COM; PHONE: 304-562-6282 –––––––––––––––––––––––––––––––– WANTED (US): CATERPILLAR CHALLENGER 85C TRACTORS - I AM IN NEED OF A USED SET OF TRACKS FOR ANY OF THE CAT CHALLENGER 65, 75 OR 85C. EMAIL: PI2279@YAHOO.COM; PHONE: 319-470-8388 –––––––––––––––––––––––––––––––– WANTED (MA): ALL MODELS CATERPILLAR EXCAVATORS - LOWER SUPPORT RAIL GOES FRONT TO BACK RIGHT SIDE AND TOOL BOX RH SIDE LOWER RAIL THAT GOES FRONT TO BACK SUPPORTING TOOL BOX. EMAIL: BILLD@TDICENZO.COM; PHONE: 207-214-9610 ––––––––––––––––––––––––––––––––

WANTED (US): CATERPILLAR CRAWLER DOZERS - LOOKING FOR D5B, D6C OR D6D. WILLING TO DO SOME WORK ON THEM IF NEEDED, EVEN PARTS MACHINE. EMAIL: JT_FERGUSON_EXC@SBCGLOBAL.NET PHONE: 317-439-7306 –––––––––––––––––––––––––––––––– WANTED (CT): ALL MODELS DYNAPAC LAND ROLLERS - WANTED GALLION STATIC PAVING ROLLERS EMAIL: JPICT@AOL.COM –––––––––––––––––––––––––––––––– WANTED (NJ): CASE BACKHOE LOADERS, MODEL 580SK, 580L, 580LII, 580SL, 580SLII, 580M, 580MII, 580MIII 580SMII, 580SMIII, 580SMIII EMAIL: FRANKHORAN@GROFFTRACTOR.COM; PHONE: 800-654-USED –––––––––––––––––––––––––––––––– WANTED (US): HITACHI EXCAVATORS LOOKING TO BUY USED HITACHI EXCAVATORS EX200LC, EX270, EX300, EX330, EX400, EX450. EMAIL: ILYAS.MTCPK@GMAIL.COM; PHONE: +923322489350 –––––––––––––––––––––––––––––––– WANTED (US): CATERPILLAR 420D WHEEL LOADER – NEED TO BUY ANY BACKHOE. ALSO LOOKING FOR EXCAVATOR AND WHEEL LOADER. EMAIL: GCESMARKETING8@GMAIL.COM; PHONE: 657-236-7399 –––––––––––––––––––––––––––––––– WANTED (WORLDWIDE): HITACHI EXCAVATORS - NEED TO BUY HITACHI EX 400-1 AND EX 450-5, ALSO LOOKING FOR ZAXIS 200 AND EX 300-1 AND EX 270-1, PLEASE LET US KNOW. EMAIL: IKRAMKHAN@IUKANDCO.COM; PHONE: +923331234598 –––––––––––––––––––––––––––––––– WANTED (WORLDWIDE): HITACHI EXCAVATORS, ALL MODELS. I NEED TO BUY CAT USED WHEEL LOADERS 916,926,936,950B/E,966E/D/F, 970F, 980C,980F ALSO CAT MOTOR GRADERS 140G,12G/H, 14G/H, 140H, 14M AND HITACHI EXCAVATORS ZX 200-1, EX 270-1, EX 300-1, EX 400-1 AND EX 450-5. (RUNNING OR NON-RUNNING MACHINES). EMAIL: AHMED@IUKANDCO.COM; PHONE: +923003695360 –––––––––––––––––––––––––––––––– WANTED (US): CATERPILLAR 926M WHEEL LOADERS - LOOKING TO BUY ANY USED CONSTRUCTION *ANY CONDITION* EMAIL: SEARCHT930@GMAIL.COM –––––––––––––––––––––––––––––––– WANTED (WORLDWIDE): CATERPILLAR 12H MOTOR GRADER - I`M LOOKING TO BUY ANY CAT 12H, ANY CONDITION EMAIL: NANI@EAGLEEQUIPMENT.CO; PHONE: 240-397-8180 ––––––––––––––––––––––––––––––––

WANTED (US): FIAT-HITACHI EXCAVATORS – LOOKING FOR PARTS AND FINAL DRIVES FOR FX310 FIAT HITACHI EXCAVATOR. EMAIL: STILLINN43@YAHOO.COM; PHONE: 973-277-3631 –––––––––––––––––––––––––––––––– WANTED (US): SKELETON – SKELETON – SKELETON BUCKETS. WANTED AND AVAILABLE. CALL US WITH WHAT YOU HAVE. SKELETON BUCKETS NEEDED FOR ALL MAKE/MODEL EXCAVATORS AND WHEEL LOADERS. EMAIL: PERCY@RANSOME-EQUIP.COM; PHONE: 215-350-1165 –––––––––––––––––––––––––––––––– WANTED (US): JOHN DEERE 700K LGP CRAWLER DOZERS – WANT TO BUY FROM USER OR BANK REPOSSESS WITH WINCH OR NOT. UNDER 900 HOURS ONLY, NO WEB BUDGET UNDER $85000.00CDN - NO JUNK NO HACKER CONTRACTORS OR PAYMENT OUT. EMAIL: JEANMAURICEBOUTIN@ VIDEOTRON.CA; PHONE: 1 450 346 8975 –––––––––––––––––––––––––––––––– WANTED (US): CATERPILLAR 140G MOTOR GRADERS – NEED TO BUY CAT 140G MOTORGRADERS 1988 OR UP .. ANY CONDITION. OFFER IT US. EMAIL: IUKANDCO@GMAIL.COM; PHONE: 03335555360 –––––––––––––––––––––––––––––––– WANTED (US): BOBCAT SKID STEER LOADERS – (2) 1978 OR 1979 BOBCAT 825 SKID STEER LOADERS - WITH PERKINS DIESEL ENGINES. CALL 412-571-2500, ASK FOR KEITH –––––––––––––––––––––––––––––––– WANTED (US): KOMATSU D475A-5E0 CRAWLER DOZER. EMAIL: TONYTHOMAS@ PACIFICCRANES.COM –––––––––––––––––––––––––––––––– WANTED (US): CATERPILLAR WHEEL LOADERS; NEED TO BUY CAT WHEEL LOADERS ANY CONDITION LIKE CAT 930, 926, 950B, 966E, AND 966F. EMAIL: IKRAMKHAN@IUKANDCO.COM –––––––––––––––––––––––––––––––– WANTED (US): CONCRETE PUMPS – SCHWING, PUTZMEISTER, ALLIANCE, ELBA,CONCORD, PUMPSTAR, ETC. ALL MODELS, BRANDS & SIZES. OLD OR NEW!!! BOOM PUMPS, TRAILER & TRUCK MOUNTED CITY PUMPS PURCHASED. OLD, RETIRED, NO LONGER USED & PARTS AND TRUCK MOUNTED PUMPS PURCHASED. EMAIL INFORMATION. INSTANT PAYMENT GUARANTEED. FINDERS FEES PAID!!! EMAIL: BBENEDETTO @ COMCAST.NET ––––––––––––––––––––––––––––––––

Page 62 • December 19, 2021 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

Auctions are subject to change, please check Auctioneers websites for details ALEX LYON & SON AUCTIONEERS 315-633-2944 • Greenwich (Albany), NY Wed., December 29, 2021 For: Very Late Model Construction Equipment & more • Online Timed January 15 - 22, 2022 For: Rental Fleet Construction Equipment & more • Online Timed Jan. 19 – Feb. 2, 2022 For: Multiple Pennsylvania Locations • Youngstown, OH Fri., January 28, 2022 For: Retirement, Complete Liquidation Trucking & Construction Company • Columbus, OH Sat., January 29, 2022 For: Very Late Model Construction Equipment & more • Bushnell, FL February 5 - 13, 2022 For: Annual Florida Auction • Western New York Fri., February 25, 2022 For: Retirement, Complete Liquidation, Trucking Company • Middletown, NY Sat., March 5, 2022 For: Two Retirements, Construction Equipment & Truck/Trailer Auction www.lyonauction.com

RITCHIE BROS. AUCTIONEERS

• Orlando, FL February 21 - 26, 2022 For: Annual Florida Auction AUCTIONS INTERNATIONAL 800-536-1401 • Online December 13 - 19, 2021 • Online December 20 - 26, 2021 • Online Dec.27 – Jan. 2, 2022 • Online January 3 – 9, 2022 • Online January 10 - 16, 2022

www.auctionsinternational.com

BAR NONE AUCTION 866-372-1700 • Online Sat., January 8, 2022 For: Sacramento, CA Monthly Public Auction • Online Fri., January 28, 2022 For: Woodburn, OR Monthly Public Auction

www.barnoneauction.com

B.I.C. AUCTIONS INC. 319-385-3399 • Live Online December 15 – 16, 2021 For: Two Day Hoette Concrete & Construction Auction www.bicauctions.com

BIDADOO AUCTIONS

1-877-BIDADOO • Online 402-421-3631 December 21, 2021 All our auctions are • Online now online bidding December 28, 2021 only! • Online • Chehalis, WA January 4, 2022 December 21, 2021 • Online • Houston, TX February 15 – 16, 2022 January 11, 2022 www.rbauction.com

www.bidadoo.com

PURPLE WAVE AUCTION • Timed Online www.purplewave.com December 14 - 21, 866-608-9283 2021 • Online For: Multi-Party To view information on upcoming auctions visit our Mon., December 27, Auction Calendar at www.constructionequipmentguide.com Construction 2021 Equipment Auction For: Sharpe Rentals HUNYADY AUCTION BIG IRON AUCTIONS Equipment Auction • Mt. Pleasant, IA COMPANY www.bigiron.com December 16, 2021 www.hunyady.com 800-937-3558 For: AgIron Mt. 800-233-6898 • Online • Online Pleasant Event Tues., December 28, • Virtual Live December 22, 2021 2021 Wed., January 12, • Timed Online For: Great Plains 2022 • Online January 7 – 12, 2022 Kubota Equipment For: Nestlerode December 29, 2021 For: Steffes Auction – Auction Contracting Co., Inc. Upper Midwest • Online • Online Surplus Liquidation Locations Tues., December 28, January 5, 2022 2021 • Timed Online • Online For: Vehicle & I.R.A.Y. AUCTION January 21 - 26, 2022 January 12, 2022 Equipment Auction www.iraymn.com For: Steffes Auction – • Online 320-968-7230 Upper Midwest Wed., December 29, Locations • Online Only HANSEN 2021 Wed., January 12, AUCTION GROUP • Timed Online For: Ag Equipment 2022 Auction February 4 - 9, 2022 www.hansenauctiongroup.com For: Heavy Equipment, For: Steffes Auction – • Online 920-383-1012 Semi, Truck, Trailer Wed., December 29, Upper Midwest Consignment Auction • Online 2021 Locations Ends December 20, For: Truck & Trailer Auction 2021 J.J. KANE AUCTIONEERS VANTAGE AUCTIONS • Online For: River Valley www.jjkane.com Thurs., December 30, www.vantageauctions.com Custom Concrete 855-GO2-KANE 2021 951-228-9040 Equipment Liquidation • Timed Online For: Construction • Lake Elsinore, CA Tues, December 21, Equipment Auction • Online Sat., January 22, 2022 2021 • Online Ends December 20, For: Public Auction For: Heavy Tues., January 11, 2021 Construction 2022 For: Construction, For: Government Equipment & more JEFF MARTIN Heavy Equipment, Auction Farm, Trucks, Trailers AUCTIONEERS, INC. www.jeffmartinauctioneers.com WSM AUCTIONEERS and More ROLLER AUCTIONEERS 601-450-6200 www.wsmauctioneers.com www.rollerauction.com • Online • Kissimmee, FL 623-936-3300 866-515-1668 Ends December 20, February 14 - 16, 2022 • Online • Virtual Online 2021 For: Annual Florida Begins Closing Sat., January 8, 2022 For: Dairyland Power Auction January 19, 2022 For: Public Auction Cooperative For: Construction & Contracting Equipment Warehouse Inventory LlOYD MEEKINS & SONS Auction YODER & FREY AUCTION CO. HEAVY EQUIPMENT www.meekinsauction.com HESS AUCTIONEERS AUCTIONS STEFFES GROUP INC. 910-739-0547

Coming Auctions

866-511-2493

www.hessauctioneers.net

• Lumberton, NC Tues., December 28, • Marietta, PA 2021 Fri., February 11, 2022 For: 27th Annual For: Truck, Trailer & Construction – Truck Auction Equipment Auction

701-237-9173 • Timed Online December 14 - 21, 2021 For: Steffes Truck & Transportation Auction www.steffesgroup.com

419-865-3990

www.yoderandfrey.com

• Kissimmee, FL February 16 – 19, 2022 For: Annual Florida Auction

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • December 19, 2021 • Page 63

Buying or Selling? Call any of these professional auction companies

Why Use Iron Bound? That’s easy... It’s SIMPLE and EFFECTIVE! We’ll market and sell your equipment, get top dollar for you and we’ll take the hassle out of the process. A Strategic As sset Managemen nt Full Service e Auction House

THE T TIME IS NOW W

Address: Iron Bound Solutions LLC 750 US HWY 180 Seminole, TX 79360

vantageauctions.c com

Phone: 432-209-5112

951.228.90040

Ritchie Bros.: Wheel Loader Prices Up 13 Percent in Nov. Ritchie Bros.’ November Market Trends Report continues to show positive pricing trends across all its equipment indexes, with medium earthmoving equipment prices up 36 percent in the United States, while truck tractors and vocational trucks are up 45 percent and 34 percent respectively (for the three months ending Oct. 31, 2021). With this report, Ritchie Bros. has included a special focus on earthmoving equipment sales in the United States and Canada. According to Ritchie Bros. price indexes, wheel loader pricing is up 13 percent in the United States, while dozer pricing is up 10 percent. The free November report is available for download at: rbassetsolutions.com/market-trends-report. “Supply chain issues continue to disrupt the equipment market, resulting in volume declines and older assets with higher usage coming to market in 2021,” said Doug Olive, senior vice president (Pricing), Ritchie Bros. “This tightening supply combined with the unprecedented demand we are driving through our numerous marketplaces is

Conveniently located for sellers in the Permian Basin, West Texas, the Panhandle & New Mexico.

resulting in strong pricing across nearly all asset categories, including dirt moving equipment like dozers, loaders and articulated dump trucks.” Doug Rusch, managing director of Rouse Sales, added, “We continue to observe strong used equipment prices, with retail values rising a further 2 percent in October. Coinciding with this rise, we are also seeing a lingering slowdown in transaction volumes, as ongoing supply chain issues continue to drive cautious fleet management decisions. Retail values now stand 14 percent higher than in January 2021.” For more information, visit www.rbauction.com. 

The Easy Way To Advertise Your Equipment Run In Two Consecutive Issues – Black & White $135 • Color $195

SEE YOUR BARGAIN AD IN COLOR.

Sentry Tires - Skid Steer and Wheel Loader Tires at Volume Buyers Prices! Call Company Wrench for Sizes & Pricing Call 866-294-6103 26 EB

ONLY $60 EXTRA FOR 2 INSERTIONS

Here's how the BARGAIN ADS Work: • Supply us with a photo of a machine (one machine per Bargain Ad) and a maximum 17 word description, plus contact and phone number. • Either email your copy & photo to: production@cegltd.com, or mail to: Construction Equipment Guide, 470 Maryland Drive, Ft Washington, PA 19034. • Cost is $135 per ad, $60 additional for color. • Your ad will run for two consecutive issues in 1 region. Your Ad Will Be Seen By Over 21,969 Construction Equipment Buyers in the Southeast States.

For more information, call Construction Equipment Guide today at

800/523-2200

Page 64 • December 19, 2021 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

Allen Butler Construction Builds Bridge Project Along U.S. 87 LUBBOCK from page 1

around the work zone. The FM 41 closure is the safest and most efficient way for crews to build the bridge entrance and exit ramps, and the frontage roads.” Once the Phase 1 frontage roads are completed in midsummer 2022, U.S. 87 traffic will be shifted onto the new lanes and FM 41 will reopen with access to U.S. 87. Crews will then begin building the Phase 2 bridge structure, targeted for an October 2023 completion date. Phase 3 final sur-

U.S. 87 is a major commerce corridor for the oil and agricultural industries that connects the Lubbock and Permian Basin regions.

Business Calendar To view our Business Calendar online, go to www.constructionequipmentguide.com. JANUARY 2022 CRANE SAFETY COURSES January 3 – January 7, 2022 Mobile Crane Operator Training, Orlando, FL January 4 – January 7, 2022 Overhead Crane Inspector Training, Houston, TX January 4 – January 7, 2022 Mobile Crane Inspector Training, Cincinnati, OH January 10 – January 11, 2022 Qualified Signal Person Training, Orlando, FL January 10 – January 14, 2022 Mobile Crane Train the Trainer, Houston, TX January 11 – January 14, 2022 Overhead Crane Inspector Training, Cincinnati, OH January 12 – January 14, 2022 Qualified Rigger Level 2 Training, Orlando, FL January 17 – January 19, 2022 Rigging Inspector Training, Cincinnati, OH January 17 – January 20, 2022 Overhead Hoist Maintenance Training, Houston, TX January 19 – January 21, 2022 Aerial Work Platform Train the Trainer, Orlando, FL January 24 – January 25, 2022 Crane Assembly/Disassembly Director Training, Houston, TX January 25 – January 28, 2022 Overhead Crane Train the Trainer, Cincinnati, OH January 26 – January 27, 2022 Critical Lift Planning/Lift Director Training, Houston, TX January 27 – January 28, 2022 Forklift Operator/Inspector Training, Orlando, FL To register and for more information, please call or email Tiffany Alston. Telephone: 800/654-5640, extension 238. Direct: 321/710-4641. Email: talston@cranesafe.com

Work on a TxDOT project to build a new bridge at the U.S. 87, FM 41 intersection began in October. Phase 1 of the project is currently being constructed.

ASSOCIATED GENERAL CONTRACTORS OF MINNESOTA (AGCMN) 2022 Minnesota Construction Summit Date: January 11-12, 2022 Location: St. Paul RiverCentre 175 Kellogg Blvd. West St. Paul, Minnesota Description: The 2022 Minnesota Construction Summit is the event of the year for the Minnesota construction industry! Featuring inspirational keynote presentations, educational sessions on topics that impact real life in our industry, exhibitors with relevant and vital products and services, and fantastic networking opportunities, this is an industry event not to be missed! Come and be a part of the 2022 Minnesota Construction Summit - Building Together Again. Registration is now open. Price: $200 For more information and to register, visit https://www.agcmn.org/events/constructionsummit./ ASSOCIATED EQUIPMENT DISTRIBUTORS (AED) 2022 AED Summit Dates: January 17-19, 2022 Location: Disney’s Coronado Springs Resort Orlando, Florida Description: The AED Summit is your annual opportunity to come together with professionals across the heavy equipment industry spectrum to improve yourself and your team and to build meaningful connections. Companies travel from all over the world to attend Summit; don’t miss your chance to meet with like-minded industry professionals! Registration is now open! Visit https://aednet.org/events/summit for more information. WORLD OF CONCRETE (WOC) World of Concrete 2022 Dates: January 18-20, 2022 (EXHIBITS) January 17-20, 2022 (EDUCATION) Location: Las Vegas Convention Center 3150 Paradise Road, Las Vegas, Nevada Description: When the world stopped, you kept going. Adapting. Giving a master class in resilience and being an essential worker. Now, celebrate how far you’ve come and discover the innovation helping our community evolve, endure, and thrive at WOC 2022. Part knowledge, part equipment, part connections—World of Concrete is 100% of what you need to keep grinding it out through disruptions to the supply chain, safety and beyond. Get your hands on advanced technology and machinery, access the newest training and techniques in con-

facing and striping will be completed in October 2024. “Keeping traffic disruptions to a minimum as the project progresses continues to be TxDOT’s biggest challenge,” Sisneros said. “Determining the need and then executing such projects requires a team effort that involves our maintenance crews, area engineers, district staff and district engineer working together to maintain roadways and improve safety, mobility and connectivity.” DPS Sergeant Johnny Bures said in an interview with KCBD, “This is a very busy intersection. It has U.S. 87 that runs through here, and of course that’s a major corridor, which connects the Permian Basin to the South Plains. With 41 running east and west, sometimes early in the morning or when the sun is setting, you have impaired visibility, also. Not to mention, with the way the road is angled, we have a lot of bad crashes out here. “[The improvements are] going to cut down on a lot of the traffic that is travelling north and south that is going to have to interact with the traffic that is on 41,” Bures added. “They will be able to utilize that flyover, where they are not actually coming through this intersection unless they are needing to turn.” The U.S. 87 bridge project is 100 percent in-state funded, said Dianah Ascencio, TxDOT public information officer. “The state funds are a combination of Category 4 [connectivity corridors] funding,” she explained. “That is, $8 million from the Lubbock District for rural connectivity, $8 million from the Lubbock Metropolitan Planning Organization for urban connectivity, and $5.6 million from the Lubbock District’s preventive maintenance funds.”  CEG

crete and masonry, and build momentum for another unstoppable year. EXHIBITS: Original equipment manufacturers from around the world and exclusive U.S. distributors of equipment, tools, products and services for the commercial construction, concrete and masonry industries. WOC attracts approximately 1,500 exhibiting companies and occupies more than 700,000 square feet of indoor and outdoor exhibit space. WHO ATTENDS WOC? More than 60,000 industry professionals from all around the world, representing all segments of the construction industry: Commercial Contractors, Concrete Contractors, Concrete Pumpers, Construction Managers, Dealers/Distributors, Decorative Concrete Contractors, Designers and Specifiers, General Contractors, Block/Segmental Unit Producers Masonry Contractors, Architects, Engineers, Block Producers, Ready Mix Producers, Rental Equipment Centers, Repair Contractors, Residential Contractors, Specialty Concrete Contractors, Precast, Pipe and Block Producers, Precast/Prestressed Producers, and more. Registration is now open! PLEASE BE ADVISED: You must register online prior to WOC 2022, as there will be NO onsite registration. Visit www.worldofconcrete.com for more information. NATIONAL ASPHALT PAVEMENT ASSOCIATION (NAPA) 2022 NAPA Annual Meeting Dates: January 23-26, 2022 Location: The Phoenician 6000 E. Camelback Road, Scottsdale, AZ 85251 Description: The NAPA Annual Meeting is in person once again! Following a safe and successful Midyear Meeting, we invite you to join us for our 2022 Annual Meeting to participate in industry-wide networking, gain practical knowledge in asphalt pavement engineering and application, and steer the industry’s future. Open your world to: • 1,000 executives, engineers, estimators, advocacy proponents, business development gurus, health and safety professionals, and industry partners • 4 general sessions • 4 educational workshops • 4 networking opportunities • 1 awards program, celebrating the best in asphalt pavement • 1 exciting and beautiful destination • 1 day on the links Registration is now open!

Visit https://www.asphaltpavement.org/pavement for more information and registration. INDEPENDENT EQUIPMENT DEALERS ASSOCIATION (IEDA) 2022 Annual Meeting Dates: February 11–13, 2022 Location: Reunion Resort Kissimmee, FL Description: T'S OUR 20TH ANNIVERSARY SO WE'RE WHOOPING IT UP BIG! IEDA Is Growing – Which Means The 2022 Annual Meeting Will Be Exploding With The Best and The Brightest of the Industry More independent equipment companies than ever now recognize the stature IEDA membership brings to their reputation and the immense value membership pours into their daily business growth 52 weeks of the year. And when this booming group gathers in person for 60 supercharged hours, the collective, best-of-the-best brain power is electrifying. Registration is now open. For more information and to register, visit https://www.iedagroup.com/2022-annual-meeting/ NATIONAL PAVEMENT EXPO (NPE) 2022 National Pavement Expo & Conference Dates: February 23-26, 2022 (Conference) February 23-25, 2022 (Expo) Location: Charlotte Convention Center Charlotte, NC Description: National Pavement Expo brings vendors and contractors together who make their living from asphalt and concrete paving, sealcoating, striping, sweeping, crack repair, pavement repair, and snow removal to network with other paving professionals and attend industry workshops. In addition to hosting 200+ leading brands from the paving and pavement maintenance industry, National Pavement Expo delivers more than 50 conference sessions over a 4-day span. Whether you want to increase industry knowledge, sharpen your skills, improve efficiency, or learn about the latest and greatest products, you can do it all here! The program design of the conference allows ample opportunity to meet and network with leading contractors in the paving industry. Registration is now open. For more information and to register, visit https://nationalpavementexpo.com

Events are subject to change, check websites for updates

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • December 19, 2021 • Page 65

Page 66 • December 19, 2021 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

ADVERTISER INDEX To read articles about these CEG advertisers, visit www.constructionequipmentguide.com 4 RIVERS EQUIPMENT....................................................................2 ACTIVE HEAVY DUTY COOLING..................................................24 AFE .................................................................................................24 ASTEC/CARLSON PAVING PRODUCTS ......................................33 ASTEC/ROADTEC ..........................................................................27 ASV ...........................................................................................48,49 AUCTION BLOCK ...........................................................................63 BARGAINS ......................................................................................63 BELL TRUCKS AMERICA INC .......................................................41 BERGMANN AMERICA ....................................................................6 BOMAG AMERICAS INC ................................................................26 CALVIN GROUP INC ......................................................................20 CONDUIT SEARCH GROUP..........................................................13 CONSTRUCTION EQUIPMENT GUIDE....................12,42,44,61,65 DOMINION EQUIPMENT PARTS...................................................40 DYNAPAC...................................................................................34,35 ECCO EQUIPMENT........................................................................23 FLANGE LOCK................................................................................15 HENDRIX MACHINERY LLC............................................................3 HITACHI CONSTRUCTION MACHINERY ...............................52,53 HYUNDAI CONSTRUCTION EQUIPMENT ..............................58,59 IEDA.................................................................................................19 IRON BOUND AUCTIONS..............................................................63 JCB INC ...........................................................................................55 JFW EQUIPMENT INC ...................................................................32 JJ SCHECKEL CORP .......................................................................5 JOHN DEERE..................................................................................39 JOHN DEERE SKID STEER ..........................................................50 KIRBY-SMITH MACHINERY INC....................................................68 KOMATSU AMERICA CORP ..........................................................67 LARMEE EQUIPMENT & SUPPLY ................................................16 LEEBOY...........................................................................................37 LIUGONG CONSTRUCTION MACHINERY .................................43 MAULDIN PAVING PRODUCTS.....................................................28 NIECE EQUIPMENT .......................................................................21 NPK CONSTRUCTION EQUIPMENT INC.....................................11

ROAD BUILDERS MACHINERY ......................................................7 ROTOTILT INC. ...............................................................................10 SAKAI AMERICA INC......................................................................31 SANY AMERICA INC.........................................................................9 TAKEUCHI ..................................................................................56,57 THUNDER CREEK..........................................................................40 TORO...............................................................................................54 TRI-STATE EQUIPMENT ................................................................17 TROPHY TRACTOR .......................................................................22 VANTAGE AUCTIONS ....................................................................63 VOLVO COMPACTION ...................................................................36 VOLVO CONSTRUCTION EQUIPMENT ..................................44,45 WACKER NEUSON ........................................................................51 WAINROY ..........................................................................................2 WEILER PRODUCTS .....................................................................30 WIRTGEN AMERICA ......................................................................29 CALIFORNIA SUPPLEMENT BAR NONE AUCTION.......................................................................1 CALIFORNIA CAT GROUP...............................................................3 GARTON TRACTOR INC..................................................................9 JCB CALIFORNIA ...........................................................................12 MEGA MACHINERY CO .................................................................10 PIRTEK CALIFORNIA .......................................................................5 SCOTT EQUIPMENT - FONTANA ...................................................2 SOUTHERN CALIFORNIA CONTRACTORS ..................................9 VOLVO CONST EQUIP & SVCS...................................................6,7 WESTERN RENTALS .....................................................................10. PACIFIC NORTHWEST SUPPLEMENT JET CITY EQUIPMENT.....................................................................5 MODERN MACHINERY....................................................................2 ORION EQUIPMENT ........................................................................8 PACWEST MACHINERY ..................................................................3 TRIAD MACHINERY .........................................................................7

The Advertisers Index is printed as a free editorial service to our advertisers and readership. Construction Equipment Guide is not responsible for errors or omissions.

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • December 19, 2021 • Page 67

www.powermotivecorp.com

POWER MOTIVE CORPORATION DENVER HEADQUARTERS 5000 Vasquez Blvd., Denver, CO 80216 303-355-5900 Colorado Springs, CO • 719-576-5541 Durango, CO • 970-259-0455 Grand Junction, CO • 970-241-1550 Milliken, CO • 970-587-1188 Cheyenne, WY • 307-634-5149

www.roadmachinery.com

ROAD MACHINERY LLC Phoenix, AZ • 480-545-2400 Phoenix, AZ • 602-252-7121 Prescott, AZ • 928-778-5621 Tucson, AZ • 520-623-8681 Bakersfield, CA • 661-695-4830 Hayward, CA • 510-659-1903 Fresno, CA • 559-834-3149 Mojave, CA • 661-824-2319 Perris, CA • 909-355-3600 Pico Rivera, CA • 562-699-6767 Redding, CA • 530-229-3820 Sacramento, CA • 916-375-3540 Santa Rosa, CA • 707-544-4147

AUTOMA MAT TED TO MAKE THE PRODUCTION N YOU NEED

www.clairemontequipment.com

CLAIREMONT EQUIPMENT 7651 Ronson Road, San Diego, CA 92111 • 858-278-8351 1330 W Mission Road, Escondido, CA 92029 • 760-739-9100 8520 Cherry Avenue, Fontana, CA 92335 • 909-429-9100 440 West Aten Road, Imperial, CA 92251 • 760-355-7700 81-501 Industrial Place, Indio, CA 92201 • 760-863-5558 4726 Convoy Street, San Diego, CA 92111 • 858-278-8338

www.kirby-smith.com

KIRBY-SMITH MACHINERY INC. 6715 W Reno Avenue • Oklahoma City, OK 73137 405-495-7820 McAlester, OK • 918-310-1550 Tulsa, OK • 918-438-1700 Abilene, TX • 325-692-6334 Amarillo, TX • 806-373-2826 Dallas, TX • 214-371-7777 Ft. Worth, TX • 817-378-0600 Lubbock, TX • 806-745-2112 Odessa, TX • 432-333-7000 Waco, TX • 254-261-1370

WAUKESHA-PEARCE INDUSTRIES, INC. www.wpi.com

12320 S. Main Street • Houston, TX 77035 • 713-723-1050 Buffalo, TX • 903-322-7150 Corpus Christi, TX • 361-884-8275 Edinburg, TX • 956-386-0107 Kilgore, TX • 903-984-2011 Pflugerville, TX • 512-251-0013 Port Arthur, TX • 409-721-5305 San Antonio, TX • 210-648-4444 Tomball, TX • 281-351-9016

Want to make your next machine acquisition really count? nt? Komatsu’s lineup of aautomated excavators, including thee all-new PC360LCi-11 and PC490LCi-11 490LCi-11 feature a revolutionary, faactory integrated, machine control system. The exclusive intelligent ligent Machine Control tecchnology lets operators focus on moving oving materials efficiently, without worrying about digging tooo deep or damaging the target surface. Contact your Komatsu distributor tributor to learn how you cann hit pay dirt today with Komatsu innovation. novation.

020

Page 68 • December 19, 2021 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

2017 Komatsu PC490LC-11 2015 Wirtgen WR200 XLI

2018 KOMATSU D61EXI-24 KM18431X 3,500 hrs.

KM17155M $239,500 3,189 hrs.

WR15021 $357,500 1,950 hrs.

2006 Komatsu WA200-5L

2017 Komatsu D85EX-18

2014 Komatsu D39PX-23

2012 Komatsu PC360LC10

KM06305U $61,500 8,343 hrs.

KM16523M $399,500 2,059 hrs.

KM14199X

$117,500 2,972 hrs.

KM12252D $118,500 6,700 hrs.

2016 KOMATSU WA270-7

2016 Komatsu PC240LC-11

2017 Deere 644K

KM16519X $157,500 3,383hrs.

$109,250 7,109 hrs.

2013 KOMATSU D65EX-17 2015 KOMATSU WA270-7

$249,500

KM13113X $129,150 5,669 hrs.

KM15353M $124,500 3,000 hrs.

KM16471M $107,500 2600 hrs.

2008 Caterpillar 963D

2018 Komatsu D65EX-18

2017 John Deere 310LEP

2014 LeeBoy 8510C

CT08803X $139,500 7,139 hrs.

KM18352X $209,500 3,600 hrs.

JD17004J $79,500 1,550 hrs.

LB14006X $79,500 2,219 hrs.

2015 Komatsu PC138USLC-10 KM15152X 4,400 hrs.

$109,500

JD17003X

2015 Komatsu HM400-5 KM15268M 10,500 hrs.

$459,500

All sales are subject to availability at time of order, prices do not include taxes or other applicable fees. Kirby-Smith Machinery Inc. doesn’t engage in exports to embargoed countries. Sold As Is Where Is.

Abilene • Amarillo • Dallas • Ft. Worth • Kansas City • Lubbock • McAlester • Odessa • Waco • Oklahoma City • St. Louis • Tulsa

Contact Terry Lyness for details and pricing.

877.549.7501