1
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Public
2
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Public
X Series Dual Separator (XDS) Dual Grain Loss Sensors • •
Proven STS Rotor Technology • •
3 Stage Rotor Chamber for maximum crop expansion Rifled Threshing Elements and Separation Tines
Active Concave Isolation • •
3
Maintains consistent concave clearance in high volume crops Better Threshing Performance
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
•
2 Sensors per rotor Improved grain loss sensing on VisionTrak Display Independent left and right display
8 Wing Discharge Beater •
Additional active separation area to handle tough, high-yielding crops
Public
NEW Dyna-Flo XL Cleaning Shoe Harvest up to 70% more, with less than 1% loss
36% larger cleaning system • •
Active Tailings Return
7.0 m2 vrs 5.9 m2 on S-Series 23% wider to evenly spread crop mat
• •
Front Step Pan •
Full Width Shoe Loss Sensing
Designed to handle more capacity (replaced shoe augers) Begins separating grain from foreign material before reaching front chaffer
•
Additional Threshing in High Moisture Crops Evenly distributes material back to return pan
• •
6 total loss sensors – 1 per bay Improved VisionTrak Display
4 Turbine Fan • •
4
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Generates even airflow by pulling air from all directions 85% more airflow for even full-width distribution
Public
X Series Dual Separator (XDS) 270 Degrees of Feeding •
3 vanes evenly deliver crop into the rotors
45% more Threshing Area • • •
More grain threshed at the front of the cleaning system Better grain quality from gently threshing 15 Threshing elements per rotor (30 total)
80% more Separating Area • • • •
More grain able to escape thick crop mats Reduces rotor loss from more rotations 7 revolutions of the crop 26 Separator tines per rotor (52 total)
5
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Update rotor gear speed ranges to prolong rotor belt life: Gear 1 speed range: 300 - 450 rpm Gear 2 speed range: 420 - 720 rpm Gear 3 speed range: 720 - 1240 rpm
Public
STS Rotor Technology Built on 20 Years of Proven STS Experience •
30” diameter Tri-Stream Rotors
Enhanced tine pattern •
S700 – 3.12m
Supporting improved crop flow
X9 – 3.51m
6” wider inlet flighting •
6
Allowing for full feeding and minimal compression
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Lengthened the Tri-Stream Rotors by 39cm • •
One separator grate longer 24” Diameter
Public
7
Concaves SW SW SW
7
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
KX SW LW
Public
Rotor Concave Cradle
8
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Public
Concaves and Threshing Separator covers •
Recommended to have 2 sets to have available at harvest time if harvesting in very dry conditions
Concave covers
9
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Public
Concaves and Threshing
Remote Operated Covers – Field Fit Option
10
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Public
Cleaning Shoe setup •
Chaffer and Sieve correct •
If screen says 5mm, check its physically 5mm.
•
Use 5mm / 15mm sieve tool to check
•
If not exact, favour more open then closed
•
Manual Pre-cleaner on 25mm set and forget but please check daily
•
In brittle stalky crops, watch for tailings overloading •
•
Flat tooth Chaffer (FTC) minimizes this
Golden rule: Open chaffer and increase fan speed to suspend MOG and let grain in.
11
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Public
Pre Cleaner locking tab
12
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Public
Residue Management
13
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Public
14
14
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Public
Power Shut Down Procedure Found in the Operators Manual and Equipment Mobile
15
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
APP
Public
16
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Public
Power Shut Down Procedure Un even shoe loading With an X9 is caused by either of the following Concave not level from left to right rotor Incorrect number of separator covers from left to right
17
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Public
Power Shut Down Procedure
High volume of Chaff causes shoe grain loss Caused by either of the following Requires Separator cover to be installed Too aggressive on crop flow settings (Feed Acel to be on slow, open concave, Slower rotor speed)
Fan Speed too low, Chaffer too closed
18
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Public
19
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Public
Engine – Variable Pitch Fan
20
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Public
ProDrive XL
Gear Range
Transmission Range Set your transmission range to an acceptable field operating range. Typically, fast enough to turn in the headlands but not a large range as that makes multifunction lever speed matching during disengagement rougher.
Recommendation is to set Range 1 no faster than 12kph (7.5mph) maximum unless crop is thin and higher speeds are required.
MAX SPEED
21
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
12
Public
Robust Belt Drive System Larger Pulleys
Longer Premium Belts
= Efficient Power Distribution S-Series uses 20 Belts and 3 Chains = 23 Drives X-Series uses 22 Belts and 1 Chain = 23 Drives
22
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Public
X9 Dual Separator (XDS) Drive Gearcase Fuse Timing A/B and A/C
IMPORTANT: Only remove the indicated parts as shown. DO NOT remove the bearing setting cover or the retention hardware. Failure to follow the procedure can result in a complete gear case failure. Remove the service plug (A) from the rotor drive gear case. Remove snap ring (B). NOTE: To remove the outer fuse shaft, use an M16 x125 cap screw. Remove the outer fuse shaft (C).NOTE: To remove the inner fuse shaft, use an M10 x150 cap screw. Remove the inner fuse shaft (D).
23
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Public
Feederhouse – Modulated Plug Removal
24
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Public
25
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Public
WHEAT TIPS AND TRICKS • Reel pitch in middle position • Slow down or stop top cross augers • Feed drum handle in middle position • Feed drum speed slow – try high for high yields • Feeder house speed slow / small cog – try high large cog for high yields be mindful of wear rate • Feed accelerator 2nd gear • Rotors 3rd gear • Tailings on wheat • Pre cleaner on 25mm – double check • One sep cover in – try two in hot dry conditions • Chopper on wheat / high speed
26
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Public
CANOLA TIPS AND TRICKS • Reel pitch in least aggressive position and keep reel bar out of crop • Cross augers match draper speed or slightly faster – faster draper speed • Feed drum handle in bottom position • Feed drum speed high • Feeder house speed high - large cog • Feed accelerator 2nd gear • Rotors 2nd gear – no slower the 500 rpm unless very dry or light • Tailings on corn • Pre cleaner on 25mm – double check • Two sep covers in • Chopper on wheat • Emu needs to be ripe – if cannot get loss or throughput under control come back to it
27
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Public
LUPINS TIPS AND TRICKS • Reel pitch in least aggressive position – work back from here to pull crop without shatter • Cross augers match draper speed • Feed drum handle in middle position – top position for light crop to sweep floor • Feed drum speed slow • Feeder house speed slow / small cog • Feed accelerator 1st gear • Rotors 2nd gear • Tailings on corn • Pre cleaner on 25mm – double check • Two sep covers in – shoe loading is massive • Chopper on wheat – for extra fine cut run in slow / corn
28
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Public
Common Things to watch for on X9 -
High Shoe loss.....
-
Rotor Loss......
-
Sample quality
-
Left and right loss difference
-
Spread quality
-
White heads.....
-
FTC Chaffer
-
Canola Rotor Speed
-
Pre cleaner
29
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Public
Machine Walkaround 30
Harvest Squad Virtual Training | July 8 th and 9 th , 2020
Public